Page 1 Pictorial index Search by illustration For safety Make sure to read through them and security Instrument How to read the gauges and meters, the variety of cluster warning lights and indicators, etc. Operation of Opening and closing the doors and windows, each adjustment before driving, etc.
Page 2 TABLE OF CONTENTS For your information....... 6 Operation of each Reading this manual ....12 component How to search......13 Pictorial index ......14 3-1. Key information Keys........146 For safety and security 3-2. Opening, closing and locking the doors Doors .........
Page 3 4-5. Using the driving Driving support systems Toyota Safety Sense P..242 4-1. Before driving (Pre-Collision System)..249 Driving the vehicle..... 190 LDA (Lane Departure Cargo and luggage.... 198 Alert with steering Vehicle load limits ..... 201 control) ......260 Trailer towing.....
Page 4 TABLE OF CONTENTS Interior features Maintenance and care 5-1. Using the air 6-1. Maintenance and care conditioning system Cleaning and protecting and defogger the vehicle exterior ..398 Automatic air Cleaning and protecting conditioning system ..344 the vehicle interior ... 401 Seat heaters......
Page 5 Alphabetical index ...... 579 For information regarding the equipment listed below, refer to “NAV- IGATION AND MULTIMEDIA SYSTEM OWNER’S MANUAL”. • Navigation system • Toyota parking assist monitor • Audio system • Panoramic view monitor • Rear view monitor system...
Page 6: For Your Information
Accessories, spare parts and modification of your Toyota A wide variety of non-genuine spare parts and accessories for Toyota vehi- cles are currently available in the market. You should know that Toyota does not warrant these products and is not responsible for their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.
Page 7 ● Seat belt pretensioner system Be sure to check with your Toyota dealer for precautionary measures or spe- cial instructions regarding installation of a mobile two-way radio system. High voltage parts and cables on the hybrid vehicles emit approximately the...
Page 8 ● Usage of data collected through Safety Connect (U.S. mainland only) If your Toyota has Safety Connect and if you have subscribed to those ser- vices, please refer to the Safety Connect Telematics Subscription Service Agreement for information on data collected and its usage.
Page 9 EDR. ● Disclosure of the EDR data Toyota will not disclose the data recorded in an EDR to a third party except when: • An agreement from the vehicle’s owner (or the lessee for a leased vehi- cle) is obtained •...
Page 10 Be sure to have the systems of the SRS airbag and seat belt pretensioner removed and disposed of by a qualified service shop or by your Toyota dealer before you scrap your vehicle.
Page 12: Reading This Manual
Reading this manual WARNING: Explains something that, if not obeyed, could cause death or serious injury to people. NOTICE: Explains something that, if not obeyed, could cause damage to or a malfunction in the vehicle or its equipment. 1 2 3 Indicates operating or working procedures.
Page 13: How To Search
How to search ■ Searching by name • Alphabetical index ..P. 579 ■ Searching installation position • Pictorial index....P. 14 ■ Searching by symptom or sound • What to do if... (Troubleshooting) ..P. 576 ■ Searching by title • Table of contents .....P. 2...
Page 14: Pictorial Index
Pictorial index Pictorial index ■ Exterior Doors ......... . . P. 150 Locking/unlocking .
Page 15 Pictorial index Windshield wipers ....... . . P. 234 Precautions for winter season ......P. 338 Fuel filler door .
Page 16: Instrument Panel
Pictorial index ■ Instrument panel Power switch ........P. 204 Starting the hybrid system/changing the modes .
Page 17 Pictorial index Parking brake ........P. 220 Applying/releasing .
Page 18 Pictorial index ■ Switches Automatic High Beam switch ......P. 230 VSC OFF switch ........P. 284 1, 2 Camera switch Trunk opener switch .
Page 19 Pictorial index Meter control switches ......P. 101, 113 Paddle shift switches ......P. 213 Vehicle-to-vehicle distance button.
Page 20 Pictorial index Wireless charger switch ......P. 368 Seat heater switches ....... P. 353 EV drive mode switch .
Page 21 Pictorial index ■ Interior SRS airbags ........P. 34 Floor mats .
Page 22 Pictorial index Interior lights/personal lights ..... . P. 354 Moon roof switches ......P. 184 “SOS”...
Page 23 For safety and security 1-1. For safe use Before driving...... 24 For safe driving ....26 Seat belts ......28 SRS airbags......34 Front passenger occupant classification system ..47 Exhaust gas precautions ....... 52 1-2. Child safety Riding with children..... 53 Child restraint systems..
Page 24: For Safe Use Before Driving
1-1. For safe use Before driving Floor mat Use only floor mats designed specifically for vehicles of the same model and model year as your vehicle. Fix them securely in place onto the carpet. Insert the retaining hooks (clips) into the floor mat eyelets. Turn the upper knob of each retaining hook (clip) to secure the floor mats in place.
Page 25 When installing the driver’s floor mat ● Do not use floor mats designed for other models or different model year vehicles, even if they are Toyota Genuine floor mats. ● Only use floor mats designed for the driver’s seat. ●...
Page 26: For Safe Driving
1-1. For safe use For safe driving For safe driving, adjust the seat and mirror to an appropriate position before driving. Correct driving posture Adjust the angle of the seat- back so that you are sitting straight up and so that you do not have to lean forward to steer.
Page 27 1-1. For safe use Adjusting the mirrors Make sure that you can see backward clearly by adjusting the inside and outside rear view mirrors properly. (→P. 177, 179) WARNING Observe the following precautions. Failure to do so may result in death or serious injury. ●...
Page 28: Seat Belts
1-1. For safe use Seat belts Make sure that all occupants are wearing their seat belts before driving the vehicle. Correct use of the seat belts ● Extend the shoulder belt so that it comes fully over the shoulder, but does not come into contact with the neck or slide off the shoulder.
Page 29 1-1. For safe use Adjusting the seat belt shoulder anchor height (front seats) Push the seat belt shoulder anchor down while pressing the release button. Push the seat belt shoulder anchor up. Move the height adjuster up and down as needed until you hear a click.
Page 30 Toyota dealer free of charge. ■ Rear seat belt Use the seat belt after passing it through the guide if the seat belt comes free from...
Page 31 Each seat belt should be used by one person only. Do not use a seat belt for more than one person at once, including children. ● Toyota recommends that children be seated in the rear seat and always use a seat belt and/or an appropriate child restraint system. ●...
Page 32 ● Ensure that the belt and plate are locked and the belt is not twisted. If the seat belt does not function correctly, immediately contact your Toyota dealer. ● Replace the seat assembly, including the belts, if your vehicle has been involved in a serious accident, even if there is no obvious damage.
Page 33 1-1. For safe use WARNING ■ Using a seat belt extender ● Do not wear the seat belt extender if you can fasten the seat belt without the extender. ● Do not use the seat belt extender when installing a child restraint system because the belt will not securely hold the child restraint system, increas- ing the risk of death or serious injury in the event of an accident.
Page 34: Srs Airbags
1-1. For safe use SRS airbags The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury. ◆...
Page 35 1-1. For safe use ◆ SRS side and curtain shield airbags SRS front side airbags Can help protect the torso of the front seat occupants SRS rear side airbags Can help protect the torso of occupants in the rear outer seats SRS curtain shield airbags ●...
Page 36 1-1. For safe use SRS airbag system components Front impact sensors SRS warning light Front passenger occupant Front passenger’s seat belt classification system (ECU buckle switch and sensors) Airbag sensor assembly Knee airbags Side impact sensors (rear) Side impact sensors (front Driver airbag doors) Driver’s...
Page 37 1-1. For safe use WARNING ■ SRS airbag precautions Observe the following precautions regarding the SRS airbags. Failure to do so may cause death or serious injury. ● The driver and all passengers in the vehicle must wear their seat belts properly.
Page 38 An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are...
Page 39 1-1. For safe use WARNING ■ SRS airbag precautions ● Do not sit on the edge of the seat or lean against the dashboard. ● Do not allow a child to stand in front of the SRS front passenger airbag unit or sit on the knees of a front passenger.
Page 40 1-1. For safe use WARNING ■ SRS airbag precautions ● Do not attach anything to or lean any- thing against areas such as the dash- board, steering wheel pad and lower portion of the instrument panel. These items can become projectiles when the SRS driver, front passenger and knee airbags deploy.
Page 41 If the areas where the SRS airbags are stored, such as the steering wheel pad and front and rear pillar garnishes, are damaged or cracked, have them replaced by your Toyota dealer. ● Do not place anything, such as a cushion, on the front passenger's seat.
Page 42 Modification and disposal of SRS airbag system components Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer. The SRS airbags may malfunction or deploy (inflate) accidentally, causing death or serious injury.
Page 43 1-1. For safe use ■ If the SRS airbags deploy (inflate) ● Slight abrasions, burns, bruising etc., may be sustained from SRS airbags, due to the extremely high speed deployment (inflation) by hot gases. ● A loud noise and white powder will be emitted. ●...
Page 44 1-1. For safe use ● Both SRS curtain shield airbags may deploy in the event of a severe side collision. ● Both SRS curtain shield airbags will deploy in the event of vehicle rollover. ● Both SRS curtain shield airbags may also deploy in the event of a severe frontal collision.
Page 45 1-1. For safe use ■ Types of collisions that may not deploy the SRS airbags (SRS side and curtain shield airbags) The SRS side and curtain shield airbags may not activate if the vehicle is subjected to a collision from the side at certain angles, or a collision to the side of the vehicle body other than the passenger compartment.
Page 46 1-1. For safe use ■ When to contact your Toyota dealer In the following cases, the vehicle will require inspection and/or repair. Con- tact your Toyota dealer as soon as possible. ● Any of the SRS airbags have been inflated. ●...
Page 47: Front Passenger Occupant Classification System
1-1. For safe use Front passenger occupant classification system Your vehicle is equipped with a front passenger occupant classi- fication system. This system detects the conditions of the front passenger seat and activates or deactivates the front passenger airbag and front passenger knee airbag. U.S.A.
Page 48 1-1. For safe use Condition and operation in the front passenger occupant classi- fication system ■ Adult “AIRBAG ON” and “AIRBAG OFF” “AIRBAG ON” indicator lights Indicator/ SRS warning light warning light Driver’s and front passenger’s seat belt reminder light flashing Front passenger airbag Devices...
Page 49 1-1. For safe use ■ Unoccupied “AIRBAG ON” and “AIRBAG OFF” “AIRBAG indicator lights OFF” Indicator/ SRS warning light warning light Driver’s and front passenger’s seat belt reminder light Front passenger airbag Devices Deactivated Front passenger knee airbag ■ There is a malfunction in the system “AIRBAG ON”...
Page 50 1-1. For safe use WARNING ■ Front passenger occupant classification system precautions Observe the following precautions regarding the front passenger occupant classification system. Failure to do so may cause death or serious injury. ● Wear the seat belt properly. ● Make sure the front passenger’s seat belt plate has not been left inserted into the buckle before someone sits in the front passenger seat.
Page 51 SRS warning light may come on to indicate a malfunction of the front passenger occupant classification system. In this case, contact your Toyota dealer immediately. ● Child restraint systems installed on the rear seat should not contact the front seatbacks.
Page 52: Exhaust Gas Precautions
Keep the trunk lid closed. ● If you smell exhaust gases in the vehicle even when the trunk lid is closed, open the windows and have the vehicle inspected at your Toyota dealer as soon as possible. ■ When parking ●...
Page 53 1-2. Child safety Riding with children Observe the following precautions when children are in the vehi- cle. Use a child restraint system appropriate for the child, until the child becomes large enough to properly wear the vehicle’s seat belt. ● It is recommended that children sit in the rear seats to avoid acci- dental contact with the shift lever, wiper switch etc.
Page 54: Child Restraint Systems
1-2. Child safety Child restraint systems Before installing a child restraint system in the vehicle, there are precautions that need to be observed, different types of child restraint systems, as well as installation methods, etc., written in this manual. Use a child restraint system when riding with a small child that can- not properly use a seat belt.
Page 55 ● Toyota strongly urges the use of a proper child restraint system that con- forms to the weight and size of the child, installed on the rear seat. Accord- ing to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat.
Page 56 1-2. Child safety Child restraint system ■ Types of child restraint system installation methods Confirm with the operation manual enclosed with the child restraint system about the installation of the child restraint system. Installation method Page Seat belt P. 61 attachment Child restraint...
Page 57 1-2. Child safety Installation method Page  Seats with an adjustable type head restraint Anchor brackets (for tether P. 70 Seats with an integrated type head  strap) attach- restraint ment...
Page 58 1-2. Child safety When using a child restraint system ■ When installing a child restraint system to a front passenger seat For the safety of a child, install child restraint systems to a rear seats. When installing child restraint system to a front passenger seat is unavoidable, adjust the seat as follows and install the child restraint system.
Page 59 1-2. Child safety WARNING ■ When using a child restraint system Observe the following precautions. Failure to do so may result in death or serious injury. ● Never install a rear-facing child restraint system on the front passenger seat even if the “AIRBAG OFF” indicator light is illuminated. In the event of an accident, the force of the rapid inflation of the front passenger airbag can cause death or serious injury to the child if the rear-facing child restraint system is installed on the front passenger seat.
Page 60 1-2. Child safety WARNING ■ When using a child restraint system ● When a booster seat is installed, always ensure that the shoulder belt is positioned across the center of the child’s shoulder. The belt should be kept away from the child’s neck, but not so that it could fall off the child’s shoulder.
Page 61 1-2. Child safety Child restraint system fixed with a seat belt A child restraint system for a small child or baby must itself be prop- erly restrained on the seat with the lap portion of the lap/shoulder belt. ◆ Installing child restraint system using a seat belt (child restraint lock function belt) Install the child restraint system in accordance to the operation manual enclosed with the child restraint system.
Page 62 1-2. Child safety While pushing child restraint system down into the rear seat, allow the shoulder belt to retract until the child restraint system is securely in place. After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.
Page 63 1-2. Child safety Run the seat belt through the child restraint system and insert the plate into the buckle. Make sure that the belt is not twisted. Fully extend the shoulder belt and allow it to retract to put it in lock mode.
Page 64 1-2. Child safety ■ Booster seat If installing the child restraint system to the front passenger seat is unavoidable, refer to P. 58 for the front passenger seat adjust- ment. High back type: If the head restraint interferes with your child restraint system, and the head restraint can be removed, remove the head...
Page 65 1-2. Child safety ◆ Removing a child restraint system installed with a seat belt Press the buckle release button and fully retract the seat belt. When releasing the buckle, the child restraint system spring up due to the rebound of the seat cushion.
Page 66 1-2. Child safety WARNING ■ When installing a child restraint system Observe the following precautions. Failure to do so may result in death or serious injury. ● Do not allow children to play with the seat belt. If the seat belt becomes twisted around a child’s neck, it may lead to choking or other serious inju- ries that could result in death.
Page 67 1-2. Child safety Child restraint system fixed with a child restraint LATCH anchor ■ Child restraint LATCH anchors LATCH anchors are provided for the outboard rear seats. (Marks displaying the location of the anchors are attached to the seats.) ■ When installing in the rear outboard seats Install the child restraint system in accordance to the operation manual enclosed with the child restraint system.
Page 68 1-2. Child safety With flexible lower attachments  Latch the hooks of the lower straps onto LATCH anchors. For owners in Canada: symbol child restraint system indicates the presence of a lower connec- tor system. Canada only  With rigid lower attachments Latch the buckles onto the LATCH anchors.
Page 69 1-2. Child safety After installing the child restraint system, rock it back and forth to ensure that it is installed securely. (→P. 66) ■ When installing in the rear center seat There are no LATCH anchors behind the rear center seat. How- ever, the inboard LATCH anchors of the outboard seats, which are 16.1 in.
Page 70 1-2. Child safety Using an anchor bracket (for top tether strap) ■ Anchor brackets (for top tether strap) Anchor brackets are provided for each rear seat. Use anchor brackets when fixing the top tether strap.  Seats with an adjustable type ...
Page 71 1-2. Child safety Open the anchor bracket cover, latch the hook onto the anchor bracket and tighten the top tether strap. Make sure the top tether strap is securely latched. (→P. 66) When installing the child restraint system with the head restraint being raised, be sure to have the top tether strap pass underneath the head restraint.
Page 72 1-2. Child safety WARNING ■ When installing a child restraint system Observe the following precautions. Failure to do so may result in death or serious injury. ● Firmly attach the top tether strap and make sure that the belt is not twisted. ●...
Page 73 1-3. Hybrid system Hybrid system features Your vehicle is a hybrid vehicle. It has characteristics different from conventional vehicles. Be sure you are closely familiar with the characteristics of your vehicle, and operate it with care. The hybrid system combines the use of a gasoline engine and an electric motor (traction motor) according to driving condi- tions, improving fuel efficiency and reducing exhaust emis- sions.
Page 74 1-3. Hybrid system ◆ When stopped/during start off The gasoline engine stops , when the vehicle is stopped. During start off, the electric motor (traction motor) drives the vehicle. At slow speeds or when traveling down a gentle slope, the engine is stopped , and the electric motor (traction motor) is used.
Page 75 30 minutes or 10 miles (16 km). If the hybrid battery (traction battery) becomes fully discharged and you are unable to start the hybrid system, contact your Toyota dealer. ■ Charging the 12-volt battery →P.
Page 76 ■ Maintenance, repair, recycling, and disposal Contact your Toyota dealer regarding maintenance, repair, recycling and dis- posal. Do not dispose of the vehicle yourself. ■ Customization...
Page 77: Hybrid System Precautions
1-3. Hybrid system Hybrid system precautions Take care when handling the hybrid system, as it is a high volt- age system (about 650 V at maximum) as well as contains parts that become extremely hot when the hybrid system is operating. Obey the warning labels attached to the vehicle.
Page 78 If the emergency shut off system activates, your vehicle will not restart. To restart the hybrid system, contact your Toyota dealer. Hybrid warning message A message is automatically displayed when a malfunction occurs in the hybrid system or an improper operation is attempted.
Page 79 If a warning light comes on, a warning message is displayed, or the 12- volt battery is disconnected The hybrid system may not start. In this case, try to start the system again. If the “READY” indicator does not come on, contact your Toyota dealer. ■ Running out of fuel...
Page 80 1-3. Hybrid system WARNING ■ High voltage precautions This vehicle has high voltage DC and AC systems as well as a 12-volt sys- tem. DC and AC high voltage is very dangerous and can cause severe burns and electric shock that may result in death or serious injury. ●...
Page 81 1-3. Hybrid system WARNING ■ Road accident cautions Observe the following precautions to reduce the risk of death or serious injury: ● Pull your vehicle off the road, apply the parking brake, shift the shift lever to P, and turn the hybrid system off. ●...
Page 82 Toyota dealer or a qualified service shop. If the hybrid battery is not dis- posed of properly, it may cause electric shock that can result in death or serious injury.
Page 83 Do not carry large amounts of water such as water cooler bottles in the vehicle. If water spills onto the hybrid battery (traction battery), the battery may be damaged. Have the vehicle inspected by your Toyota dealer. ● There is a filter installed to the air intake vent. When the filter remains noticeably dirty even after cleaning the air intake vent, filter cleaning or replacement is recommended.
Page 84: Theft Deterrent System Immobilizer System
1-4. Theft deterrent system Immobilizer system The vehicle’s keys have built-in transponder chips that prevent the hybrid system from starting if a key has not been previously registered in the vehicle’s on-board computer. Never leave the keys inside the vehicle when you leave the vehi- cle.
Page 85 1-4. Theft deterrent system ■ Certifications for the immobilizer system  For vehicles sold in the U.S.A.  For vehicles sold in Canada NOTICE ■ To ensure the system operates correctly Do not modify or remove the system. If modified or removed, the proper operation of the system cannot be guaranteed.
Page 86: Alarm
1-4. Theft deterrent system Alarm The alarm The alarm uses light and sound to give an alert when an intrusion is detected. The alarm is triggered in the following situations when the alarm is set: ● A locked door is unlocked in any way other than using the entry function, wireless remote control or mechanical key.
Page 87 1-4. Theft deterrent system ■ System maintenance The vehicle has a maintenance-free type alarm system. ■ Items to check before locking the vehicle To prevent unexpected triggering of the alarm and vehicle theft, make sure of the following: ● Nobody is in the vehicle. ●...
Page 88 1-4. Theft deterrent system NOTICE ■ To ensure the system operates correctly Do not modify or remove the system. If modified or removed, the proper operation of the system cannot be guaranteed.
Page 89: 2. Instrument Cluster
Instrument cluster Instrument cluster Warning lights and indicators ......90 Gauges and meters .... 96 Multi-information display (4.2-inch display) .... 100 Multi-information display (7-inch display) ....112 Head-up display ....128 Energy monitor/ consumption screen..135...
Page 90: Warning Lights And Indicators
2. Instrument cluster Warning lights and indicators The warning lights and indicators on the instrument cluster, cen- ter panel and outside rear view mirrors inform the driver of the status of the vehicle’s various systems. For the purpose of explanation, the following illustrations dis- play all warning lights and indicators illuminated.
Page 91 2. Instrument cluster Warning lights Warning lights inform the driver of malfunctions in any of the vehicle’s systems. Brake system warning Parking brake indicator light (→P. 480) (→P. 481) (U.S.A.) (Canada) 1, 2 Brake system warning Brake hold operated light (→P. 480) indicator (→P.
Page 92 There may be a malfunction in a system if a light does not come on, or turn off. Have the vehicle inspected by your Toyota dealer. : This light flashes to indicate a malfunction.
Page 93 2. Instrument cluster Indicators The indicators inform the driver of the operating state of the vehicle’s various systems. Radar cruise control Turn signal indicator indicator (→P. 219) (→P. 270) Cruise control “SET” Headlight indicator indicator (→P. 227) (→P. 270) (U.S.A.) 1, 2 Tail light indicator PCS warning light...
Page 94 There may be a malfunction in a system if a light does not come on, or turn off. Have the vehicle inspected by your Toyota dealer. : This light turns on when the system is off.
Page 95 Have the vehicle inspected by your Toyota dealer immediately if this occurs.
Page 96: Gauges And Meters
2. Instrument cluster Gauges and meters 4.2-inch display  7-inch display ...
Page 97 2. Instrument cluster Hybrid System Indicator Displays hybrid system output or regeneration level (→P. 98) Shift position (→P. 213) Outside temperature Displays the outside temperature within the range of -40°F (-40°C) to 122°F (50°C). Low outside temperature indicator comes on when the ambient temperature is 37°F (3°C) or lower.
Page 98 2. Instrument cluster ■ The meters and display illuminate when The power switch is in ON mode. ■ Brightness of the meters (day mode and night mode) ● The brightness of the meters is changed between day mode and night mode.
Page 99 When the outside temperature has changed suddenly (at the entrance/exit of a garage, tunnel, etc.) ● When “− −” or “E” is displayed, the system may be malfunctioning. Take your vehicle to your Toyota dealer. NOTICE ■ To prevent damage to the engine and its components The engine may be overheating if the engine coolant temperature gauge is in the red zone (H).
Page 100 2. Instrument cluster Multi-information display (4.2-inch display) Summary of functions The multi-information display presents the driver with a variety of driv- ing-related data, such as the current outside temperature. The multi- information display can also be used to change the display settings and other settings.
Page 101 2. Instrument cluster Using the multi-information display ◆ Using the content display area The content display area is operated using the meter control switches. Scroll screens , change the displayed content and move the cursor Press: Enter/Set Press and hold: Reset Return previous screen...
Page 102 2. Instrument cluster Menu icons Select a menu icon to display its content. Drive information (→P. 103) Select to display various drive data. Audio system-linked display Select to enable selection of an audio source or track on the meter using the meter control switches. Driving assist system information Select to display the operational status of the following systems: •...
Page 103 2. Instrument cluster Drive information ( ■ Trip (after start) Average fuel economy Displays the average fuel con- sumption since hybrid system start. Average vehicle speed Displays the average vehicle speed since hybrid system start. Elapsed time Displays the time elapsed since hybrid system start.
Page 104 2. Instrument cluster ■ Tank (after refuel) 1, 2 Driving range Displays the driving range with remaining fuel. 1, 3 Average fuel economy Displays the average fuel con- sumption since the vehicle was refueled. : When only a small amount of fuel is added to the tank, the display may not be updated.
Page 105 2. Instrument cluster Settings display ( ◆ Changing settings Use the meter control switches on the steering wheel to change settings. Press to select Operate the switches to select a desired item. Change the setting by referring to the message displayed on the screen.
Page 106 2. Instrument cluster ■ PCS (Pre-Collision System) (→P. 249) The following pre-collision system settings can be changed: Item Settings Details Select to enable/disable the pre- collision system. Select to change the warning Warning sensitivity timing. ■ BSM (Blind Spot Monitor) function (if equipped) (→P. 290) Item Settings Details...
Page 107 ID codes must be (vehicles without a tire inflation pres- registered by a Toyota dealer. sure display function) For information regarding chang- ing the registered ID code set, contact your Toyota dealer.
Page 108 2. Instrument cluster Item Settings Details Scheduled maintenance display Select to reset the message indi- cating maintenance is required, Maintenance data reset after the required maintenance is performed. (→P. 405) ■ Meter settings Item Settings Details Select to change the language Language displayed.
Page 109 2. Instrument cluster Odometer/trip meter ■ Odometer Displays the total distance the vehicle has been driven. ■ Trip meter A/trip meter B Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and dis- play different distances independently.
Page 110 2. Instrument cluster ■ Suspension of the settings display ● Some settings cannot be changed while driving. When changing settings, park the vehicle in a safe place. ● If a warning message is displayed, operation of the settings display will be suspended.
Page 111 2. Instrument cluster WARNING ■ Caution for use while driving ● When operating the multi-information display while driving, pay extra attention to the safety of the area around the vehicle. ● Do not look continuously at the multi-information display while driving as you may fail to see pedestrians, objects on the road, etc.
Page 112 2. Instrument cluster Multi-information display (7-inch display) Summary of functions The multi-information display presents the driver with a variety of driv- ing-related data, such as the current outside temperature. The multi- information display can also be used to change the display settings and other settings.
Page 113 2. Instrument cluster Odometer/trip meter (→P. 125) Shift position (→P. 213) Outside temperature (→P. 96) Menu icons (→P. 114) “ODO/TRIP” switch (→P. 113) Meter control switches (→P. 113) Using the multi-information display ◆ Using the content display area The content display area is operated using the meter control switches.
Page 114 2. Instrument cluster Menu icons Select a menu icon to display its content. Warning message display (→P. 490) This menu icon will be displayed only when a warning message can be displayed. Select to display warning messages and measures to be taken if a mal- function is detected.
Page 115 2. Instrument cluster Eco-friendly driving information ( ■ Fuel consumption Current fuel consumption Displays the instantaneous cur- rent fuel consumption. Average fuel economy (after start) Displays the average fuel con- sumption since hybrid system start. Driving range 2, 3 Displays the driving range with remaining fuel. Gadget The following items can be displayed by changing the settings for gad- get content and fuel economy type on...
Page 116 2. Instrument cluster Average fuel economy Displayed item (listed below) can be changed on the fuel economy type screen of . (→P. 119) ● Total (after reset) 1, 5 Displays the average fuel consumption since the display was reset. ● Tank (after refuel) Displays the average fuel consumption since the vehicle was refu- 1, 2 eled.
Page 117 2. Instrument cluster ■ Eco guide The Eco guide displays a guide for eco-friendly acceleration and scores which represent an evaluation of how the vehicle has been driven ecologically in different states. ECO Accelerator Guidance Eco score ● ECO Accelerator Guidance Eco area Indicates that the vehicle is being driven in an Eco-friendly...
Page 118 2. Instrument cluster ● Eco score The following 3 Eco driving methods are evaluated in 5 levels: Smooth start-off acceleration, driving without sudden acceleration, and smooth stopping. When the vehicle is stopped, an Eco score out of 100 points will be displayed. Eco start status Eco cruise status Eco stop status...
Page 119 2. Instrument cluster Settings display ( ◆ Changing settings Use the meter control switches on the steering wheel to change settings. Press to select Operate the switches to select a desired item. Press or press and hold The available settings will differ depending on if is pressed or pressed and held.
Page 120 2. Instrument cluster ■ PCS (Pre-Collision System) (→P. 249) Press and hold to change the settings of the following items: Item Settings Details Select to enable/disable the pre- collision system. Select to change the warning Warning sensitivity timing. ■ BSM (Blind Spot Monitor) (if equipped) (→P. 290) Press to enable/disable the Blind Spot Monitor function.
Page 121 2. Instrument cluster ■ RCTA (Rear Cross Traffic Alert) (if equipped) (→P. 290) Press to enable/disable the Rear Cross Traffic Alert function. Item Settings Details Select to enable/disable the Rear RCTA Cross Traffic Alert function. Press and hold to change the settings of the following item: Item Settings Details...
Page 122 2. Instrument cluster ■ HUD (Head-up display) (→P. 128) Press to enable/disable the head-up display. Item Settings Details Select enable/disable head-up display. Press and hold to change the settings of the following items: Item Settings Details Select to adjust the brightness/ position of the head-up display.
Page 123 2. Instrument cluster ■ Vehicle settings Press and hold to change the settings of the following items: Item Settings Details TPWS (Tire pressure warning system) (→P. 429) Select to initialize the tire pres- sure warning system. To per- form initialization, press and hold Set pressure (tire pressure warning sys- switch.
Page 124 2. Instrument cluster ■ Meter settings Press and hold to change the settings of the following items: Item Settings Details Select to change the language Language displayed. Select to change the units of Units measure displayed. Select to enable/disable the EV (EV indicator) indicator.
Page 125 2. Instrument cluster Odometer/trip meter ■ Odometer Displays the total distance the vehicle has been driven. ■ Trip meter A/trip meter B Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and dis- play different distances independently.
Page 126 2. Instrument cluster ■ The Eco guide will not operate when The Eco guide will not operate in the following situations: ● The Hybrid System Indicator is not operating. ● The vehicle is being driven using the dynamic radar cruise control with full- speed range.
Page 127 2. Instrument cluster WARNING ■ Caution for use while driving ● When operating the multi-information display while driving, pay extra attention to the safety of the area around the vehicle. ● Do not look continuously at the multi-information display while driving as you may fail to see pedestrians, objects on the road, etc.
Page 128: Head-Up Display
2. Instrument cluster ∗ Head-up display Summary of functions The head-up display is linked to the meters and navigation system (if equipped) and projects a variety of information in front of the driver, such as the current vehicle speed. Driving assist system status/navigation system-linked display area (if equipped) (→P.
Page 129 2. Instrument cluster Using the head-up display Select on the multi-information display (→P. 119) and then ◆ Enabling/disabling the head-up display Press to enable/disable the head-up display. ◆ Changing the head-up display settings Press and hold to change the following settings: ■...
Page 130 2. Instrument cluster Driving assist system status/navigation system-linked display area (if equipped) ◆ Driving assist system status display Displays the operational status of the following systems: • Dynamic radar cruise control with full-speed range (→P. 270) • LDA (Lane Departure Alert with steering control) (→P. 260) •...
Page 131 2. Instrument cluster Hybrid System Indicator/Tachometer ■ Hybrid System Indicator Charge area Hybrid Eco area Eco area Power area Displayed content is the same as that displayed on the meter (Hybrid System Indicator). For details, refer to P. 98. ■ Tachometer Displays the engine speed in revolutions per minute.
Page 132 2. Instrument cluster Information display area Displays the following items in the appropriate situation: ■ Warning/Message ● Alert from the LDA (Lane Departure Alert with steering control) ● Dynamic radar cruise control with full-speed range ● message Displayed when a suggestion/advice pop-up display is displayed on the multi-information display.
Page 133 2. Instrument cluster ■ Head-up display The head-up display may seem dark or hard to see when viewed through sunglasses, especially polarized sunglasses. Adjust the brightness of the head-up display or remove your sunglasses. ■ Display brightness The brightness of the head-up display can be adjusted on of the multi- information display.
Page 134 2. Instrument cluster NOTICE ■ To prevent damage to components ● Do not place any drinks near the head- up display projector. If the projector gets wet, electrical malfunctions may result. ● Do not place anything on or put stickers onto the head-up display projector.
Page 135: Energy Monitor Consumption Screen
2. Instrument cluster Energy monitor/consumption screen You can view the status of your hybrid system on the multi-infor- mation display, the audio system screen. Audio system screen Multi-information display...
Page 136 2. Instrument cluster Energy monitor Entune Audio or Entune Audio Plus (vehicles without Data Commu-  nication Module) Press the “INFO” button. If the “Trip Information” or “History” screen displayed, select “Energy”. Entune Audio Plus (vehicles with Data Communication Module) ...
Page 137 2. Instrument cluster ■ Multi-information display Press meter control switches on the steering wheel several times to select the energy monitor display. Multi-information Audio system screen display Vehicles with 4.2-inch display: Vehicles with 7-inch When the vehi- display: cle is powered by the electric motor (traction...
Page 138 2. Instrument cluster Multi-information Audio system screen display Vehicles with 4.2-inch display: Vehicles with 7-inch When the vehi- display: cle is powered by the gasoline engine Vehicles with 4.2-inch display: When the vehi- Vehicles with 7-inch cle is powered display: by both the gas- oline engine and electric...
Page 139 2. Instrument cluster Multi-information Audio system screen display Vehicles with 4.2-inch display: Vehicles with 7-inch display: When the vehi- cle is charging the hybrid bat- Vehicles with 4.2-inch tery (traction display: battery) Vehicles with 7-inch display:...
Page 140 2. Instrument cluster Multi-information Audio system screen display Vehicles with 4.2-inch display: Vehicles with 7-inch display: When there is no energy flow Vehicles with 4.2-inch display: Hybrid battery Full (traction bat- Vehicles with 7-inch tery) status display: Full Full...
Page 141 2. Instrument cluster Fuel consumption screen ■ Trip information  Entune Audio or Entune Audio Plus (vehicles without Data Com- munication Module) Press the “INFO” button. (→P. 136) If the “Energy Monitor” or “History” screen is displayed, select “Trip Information”. ...
Page 142 2. Instrument cluster ■ History  Entune Audio or Entune Audio Plus (vehicles without Data Com- munication Module) Press the “INFO” button. (→P. 136) If the “Energy Monitor” or “Trip Information” screen is displayed, select “History”.  Entune Audio Plus (vehicles with Data Communication Module) Press the “INFO”...
Page 143 2. Instrument cluster ■ Resetting the consumption data Selecting “Clear” on the “Trip Information” screen will reset the fuel consump- tion and the regenerated energy for the past 15 minutes. Selecting “Clear” on the “History” screen will reset the past records and best past fuel consump- tion.
Page 144 2. Instrument cluster...
Page 145 Operation of each component 3-1. Key information Keys ........146 3-2. Opening, closing and locking the doors Doors ........ 150 Trunk......... 156 Smart key system ..... 160 3-3. Adjusting the seats Front seats ......169 Rear seats......171 Head restraints....173 3-4.
Page 146: Keys
3 seconds unlocks the other doors. Opens the windows and the 1, 2 moon roof (→P. 150) Opens the trunk (→P. 156) Sounds the alarm (→P. 147) : If equipped : This setting must be customized at your Toyota dealer.
Page 147 ■ If you lose your keys New genuine keys can be made by your Toyota dealer using the other mechanical key and the key number stamped on your key number plate. Keep the plate in a safe place such as your wallet, not in the vehicle.
Page 148 ■ Confirmation of the registered key number The number of keys already registered to the vehicle can be confirmed. Ask your Toyota dealer for details. ■ If a wrong key is used The key cylinder rotates freely to isolate inside mechanism.
Page 149 Toyota dealer. ■ When an electronic key is lost If the electronic key remains lost, the risk of vehicle theft increases signifi- cantly. Visit your Toyota dealer immediately with all remaining electronic keys that were provided with your vehicle.
Page 150: Locking The Doors Doors
Pressing the but- ton again within 3 seconds unlocks the other doors. Press and hold to open the win- 1, 2 dows and the moon roof. (→P. 181, 185) : If equipped : This setting must be customized at your Toyota dealer.
Page 151 3-2. Opening, closing and locking the doors ■ Operation signals Doors: A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: Once; Unlocked: Twice) Windows and moon roof: A buzzer sounds to indicate that the windows and moon roof are opening. ■...
Page 152 3-2. Opening, closing and locking the doors Unlocking and locking the doors from the inside ◆ Door lock switches Locks all the doors Unlocks all the doors ◆ Inside lock buttons Locks the door Unlocks the door The front doors can be opened by pulling the inside handle even if the lock buttons are in the lock position.
Page 153 3-2. Opening, closing and locking the doors Rear door child-protector lock The door cannot be opened from inside the vehicle when the lock is set. Unlock Lock These locks can be set to prevent children from opening the rear doors. Push down on each rear door switch to lock both rear doors.
Page 154 3-2. Opening, closing and locking the doors ■ Switching the door unlock function It is possible to set which doors the entry function unlocks using the wireless remote control. Turn the power switch off. When the indicator light on the key surface is not on, press and hold for approximately 5 seconds while pressing and holding The setting changes each time an operation is performed, as shown below.
Page 155 3-2. Opening, closing and locking the doors ■ Conditions affecting the operation of the smart key system or wireless remote control →P. 163 ■ Customization Some functions can be customized. (→P. 551) WARNING ■ To prevent an accident Observe the following precautions while driving the vehicle. Failure to do so may result in a door opening and an occupant falling out, resulting in death or serious injury.
Page 156: Trunk
3-2. Opening, closing and locking the doors Trunk The trunk can be opened using the trunk opener switch, entry function or wireless remote control. Opening the trunk from inside the vehicle Press the trunk opener switch. Opening the trunk from outside the vehicle ◆...
Page 157 3-2. Opening, closing and locking the doors ■ Trunk light The trunk light turns on when the trunk is opened. ■ Function to prevent the trunk being locked with the electronic key inside ● When all doors are locked, closing the trunk lid with the electronic key left inside the trunk will sound an alarm.
Page 158 3-2. Opening, closing and locking the doors WARNING Observe the following precautions. Failure to do so may result in death or serious injury. ■ Before driving ● Make sure that the trunk lid is fully closed. If the trunk lid is not fully closed, it may open unexpectedly while driving and hit near-by objects or luggage in the trunk may be thrown out, causing an accident.
Page 159 ● Do not attach any accessories other than genuine Toyota parts to the trunk lid. Such additional weight on the trunk lid may cause the lid to suddenly shut again after it is opened.
Page 160: Smart Key System
3-2. Opening, closing and locking the doors Smart key system The following operations can be performed simply by carrying the electronic key on your person, for example in your pocket. (The driver should always carry the electronic key.) ● Locks and unlocks the doors (→P. 150) ●...
Page 161 3-2. Opening, closing and locking the doors ■ Effective range (areas within which the electronic key is detected) When locking or unlocking the doors The system can be operated when the electronic key is within about 2.3 ft. (0.7 m) of either of the front out- side door handles.
Page 162 3-2. Opening, closing and locking the doors ■ Battery-saving function The battery-saving function will be activated in order to prevent the electronic key battery and the 12-volt battery from being discharged while the vehicle is not in operation for a long time. ●...
Page 163 3-2. Opening, closing and locking the doors ■ Conditions affecting operation The smart key system, wireless remote control and immobilizer system use weak radio waves. In the following situations, the communication between the electronic key and the vehicle may be affected, preventing the smart key system, wireless remote control and immobilizer system from operating prop- erly.
Page 164 3-2. Opening, closing and locking the doors ■ Note for the entry function ● Even when the electronic key is within the effective range (detection areas), the system may not operate properly in the following cases: • The electronic key is too close to the window or outside door handle, near the ground, or in a high place when the doors are locked or unlocked.
Page 165 Fingernails may scrape against the door during operation of the door han- dle. Be careful not to injure fingernails or damage the surface of the door. : This setting can be customized at your Toyota dealer. ■ When the vehicle is not driven for extended periods ●...
Page 166 3-2. Opening, closing and locking the doors ■ Certification for the smart key system  For vehicles sold in the U.S.A.
Page 167 3-2. Opening, closing and locking the doors  For vehicles sold in Canada...
Page 168 (→P. 160) The radio waves may affect the operation of such devices. If necessary, the entry function can be disabled. Ask your Toyota dealer for details, such as the frequency of radio waves and timing of the emitted radio waves.
Page 169 3-3. Adjusting the seats Front seats Adjustment procedure  Manual seat Seat position adjustment lever Seatback angle adjustment lever Vertical height adjustment lever Power seat  Seat position adjustment switch Seatback angle adjustment switch Seat cushion (front) angle adjustment switch Vertical height adjustment...
Page 170 3-3. Adjusting the seats WARNING ■ When adjusting the seat position ● Take care when adjusting the seat position to ensure that other passen- gers are not injured by the moving seat. ● Do not put your hands under the seat or near the moving parts to avoid injury.
Page 171: Rear Seats
3-3. Adjusting the seats Rear seats The seatbacks of the rear seats can be folded down. Folding down the rear seatbacks Pull the seatback lever in the trunk for the seatback you wish to fold down and then fold the seatback down.
Page 172 3-3. Adjusting the seats WARNING ■ When folding the seatbacks down Observe the following precautions. Failure to do so may result in death or serious injury. ● Do not fold the seatbacks down while driving. ● Stop the vehicle on level ground, set the parking brake and shift the shift lever to P.
Page 173: Head Restraints
3-3. Adjusting the seats Head restraints Head restraints are provided for all seats.  Adjustable type Pull the head restraint up. Down Push the head restraint down while pressing the lock release button. Lock release button Integrated type  Head restraints cannot be adjusted or removed. ■...
Page 174 3-3. Adjusting the seats ■ Installing the head restraints  Front seats Align the head restraint with the installa- tion holes and push it down to the lock position. Press and hold the lock release button when lowering the head restraint. Lock release button ...
Page 175 3-4. Adjusting the steering wheel and mirrors Steering wheel Adjustment procedure Hold the steering wheel and push the lever down. Adjust to the ideal position by moving the steering wheel hori- zontally and vertically. After adjustment, pull the lever up to secure the steering wheel.
Page 176 3-4. Adjusting the steering wheel and mirrors WARNING ■ Caution while driving Do not adjust the steering wheel while driving. Doing so may cause the driver to mishandle the vehicle and cause an acci- dent, resulting in death or serious injury. ■...
Page 177: Inside Rear View Mirror
3-4. Adjusting the steering wheel and mirrors Inside rear view mirror The rear view mirror’s position can be adjusted to enable suffi- cient confirmation of the rear view. Adjusting the height of rear view mirror The height of the rear view mirror can be adjusted to suit your driving posture.
Page 178 3-4. Adjusting the steering wheel and mirrors Auto anti-glare inside rear view mirror  Responding to the level of brightness of the headlights of vehicles behind, the reflected light is automatically reduced. Changing automatic anti-glare function mode On/Off When the automatic anti-glare function is in ON mode, the indica- tor illuminates.
Page 179: Outside Rear View Mirrors
3-4. Adjusting the steering wheel and mirrors Outside rear view mirrors Adjustment procedure To select a mirror to adjust, turn the switch. Left Right To adjust the mirror, operate the switch. Right Down Left Folding the mirrors Push the mirror back in the direc- tion of the vehicle’s rear.
Page 180 3-4. Adjusting the steering wheel and mirrors WARNING ■ Important points while driving Observe the following precautions while driving. Failure to do so may result in loss of control of the vehicle and cause an accident, resulting in death or serious injury. ●...
Page 181 3-5. Opening and closing the windows Power windows Opening and closing procedures The power windows can be opened and closed using the switches. Operating the switch moves the windows as follows: Closing One-touch closing Opening One-touch opening : To stop the window partway, oper- ate the switch in the opposite direc- tion.
Page 182 The power windows can be opened using the wireless remote control. → P. 150) : These settings must be customized at your Toyota dealer. ■ Alarm The alarm may be triggered if the alarm is set and a power window is closed using the door lock linked power window operation function.
Page 183 3-5. Opening and closing the windows ■ Customization Some functions can be customized. (→P. 551) WARNING Observe the following precautions. Failure to do so may result in death or serious injury. ■ Closing the windows ● The driver is responsible for all the power window operations, including the operation for the passengers.
Page 184: Moon Roof
3-5. Opening and closing the windows ∗ Moon roof Use the overhead switches to open and close the moon roof and tilt it up and down. Opening and closing Opens the moon roof The moon roof stops slightly before the fully open position to reduce wind noise.
Page 185 Door lock linked moon roof operation ● The moon roof can be opened and closed using the mechanical key. (→P. 509) ● The moon roof can be opened using the wireless remote control. (→P. 150) : These settings must be customized at your Toyota dealer.
Page 186 If the moon roof does not fully close even after performing the above proce- dure correctly, have the vehicle inspected by your Toyota dealer. ■ Alarm The alarm may be triggered if the alarm is set and the moon roof is closed using the door lock linked moon roof operation function.
Page 187 3-5. Opening and closing the windows WARNING Observe the following precautions. Failure to do so may cause death or serious injury. ■ Opening the moon roof ● Do not allow any passengers to put their hands or heads outside the vehi- cle while it is moving.
Page 188 3-5. Opening and closing the windows...
Page 189 Cargo and luggage ... 198 4-5. Using the driving Vehicle load limits ..... 201 support systems Trailer towing..... 202 Toyota Safety Sense P ..242 Dinghy towing ....203 4-2. Driving procedures (Pre-Collision System) ..249 Power (ignition) switch ..204 LDA (Lane Departure Alert EV drive mode ....
Page 190 4-1. Before driving Driving the vehicle The following procedures should be observed to ensure safe driving: Starting the hybrid system →P. 204 Driving With the brake pedal depressed, shift the shift lever to D. (→P. 213) Release the parking brake. (→P. 220) Gradually release the brake pedal and gently depress the accelera- tor pedal to accelerate the vehicle.
Page 191 4-1. Before driving ■ When starting off on an uphill The hill-start assist control will activate. (→P. 284) ■ For fuel-efficient driving Keep in mind that hybrid vehicles are similar to conventional vehicles, and it is necessary to refrain from activities such as sudden acceleration. (→P. 335) ■...
Page 192 284) to cancel Drive-Start Control so that the vehicle may become able to escape from the mud or fresh snow. ■ Breaking in your new Toyota To extend the life of the vehicle, observing the following precautions is recom- mended: ●...
Page 193 4-1. Before driving WARNING Observe the following precautions. Failure to do so may result in death or serious injury. ■ When starting the vehicle Always keep your foot on the brake pedal while stopped with the “READY” indicator is illuminated. This prevents the vehicle from creeping. ■...
Page 194 4-1. Before driving WARNING Observe the following precautions. Failure to do so may result in death or serious injury. ■ When driving the vehicle ● Do not drive in excess of the speed limit. Even if the legal speed limit per- mits it, do not drive over 85 mph (140 km/h) unless your vehicle has high- speed capability tires.
Page 195 If you hear a squealing or scraping noise (brake pad wear limit indica- tors) Have the brake pads checked and replaced by your Toyota dealer as soon as possible. Rotor damage may result if the pads are not replaced when needed.
Page 196 4-1. Before driving WARNING Observe the following precautions. Failure to do so may result in death or serious injury. ■ When the vehicle is parked ● Do not leave a door or window open if the curved glass is coated with a metallized film such as a silver-colored one.
Page 197 Short in electrical components ● Engine damage caused by water immersion In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following: ● Brake function ●...
Page 198 Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. (→P. 201) Toyota does not recommend towing a trailer with your vehicle. Your vehicle is not designed for trailer towing.
Page 199 4-1. Before driving Calculation formula for your vehicle Cargo capacity Total load capacity (vehicle capacity weight) (→P. 526) When 2 people with the combined weight of A lb. (kg) are riding in your vehicle, which has a total load capacity (vehicle capacity weight) of B lb.
Page 200 4-1. Before driving WARNING ■ Things that must not be carried in the trunk The following things may cause a fire if loaded in the trunk: ● Receptacles containing gasoline ● Aerosol cans ■ Storage precautions Observe the following precautions. Failure to do so may prevent the pedals from being depressed properly, may block the driver’s vision, or may result in items hitting the driver or passengers, possibly causing an accident.
Page 201 Seating capacity means the maximum number of occupants whose estimated average weight is 150 lb. (68 kg) per person. ◆ Towing capacity Toyota does not recommend towing a trailer with your vehicle. ◆ Cargo capacity Cargo capacity may increase or decrease depending on the weight and the number of occupants.
Page 202 Trailer towing Toyota does not recommend towing a trailer with your vehicle. Toyota also does not recommend the installation of a tow hitch or the use of a tow hitch carrier for a wheelchair, scooter, bicy- cle, etc. Your vehicle is not designed for trailer towing or for the...
Page 203 4-1. Before driving Dinghy towing Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home. NOTICE ■ To avoid serious damage to your vehicle Do not tow your vehicle with four wheels on the ground.
Page 204 4-2. Driving procedures Power (ignition) switch Performing the following operations when carrying the elec- tronic key on your person starts the hybrid system or changes power switch modes. Starting the hybrid system Check that the parking brake is set. Check that the shift lever is in P. Firmly depress the brake pedal.
Page 205 4-2. Driving procedures Changing power switch modes Modes can be changed by pressing the power switch with brake pedal released. (The mode changes each time the switch is pressed.) The emergency flashers can be used. ACCESSORY mode Some electrical components such as the audio system can be used.
Page 206 If the hybrid system does not start ● The immobilizer system may not have been deactivated. (→P. 84) Contact your Toyota dealer. ● Check that the shift lever is securely set in P. The hybrid system may not start if the shift lever is displaced out of P.
Page 207 ■ If the “READY” indicator does not come on In the event that the “READY” indicator does not come on even after perform- ing the proper procedures for starting the vehicle, contact your Toyota dealer immediately. ■ If the hybrid system is malfunctioning →P.
Page 208 4-2. Driving procedures WARNING ■ When starting the hybrid system Always start the hybrid system while sitting in the driver’s seat. Do not depress the accelerator pedal while starting the hybrid system under any circumstances. Doing so may cause an accident resulting in death or serious injury. ■...
Page 209 Do not depress the accelerator pedal unnecessarily. ● If the hybrid system becomes difficult to start, have your vehicle checked by your Toyota dealer immediately. ■ Symptoms indicating a malfunction with the power switch If the power switch seems to be operating somewhat differently than usual, such as the switch sticking slightly, there may be a malfunction.
Page 210 4-2. Driving procedures EV drive mode In EV drive mode, electric power is supplied by the hybrid bat- tery (traction battery), and only the electric motor (traction motor) is used to drive the vehicle. This mode allows you to drive in residential areas early in the morning and late at night, or in indoor parking lots etc.
Page 211 4-2. Driving procedures ■ Switching to EV drive mode when the gasoline engine is cold If the hybrid system is started while the gasoline engine is cold, the gasoline engine will start automatically after a short period of time in order to warm up. In this case, you will become unable to switch to EV drive mode.
Page 212 4-2. Driving procedures WARNING ■ Caution while driving When driving in EV drive mode no engine noise is made. As such, pedestri- ans, people riding bicycles or other people and vehicles in the surrounding area may not be aware of the vehicle starting off or approaching them. Therefore, take extra care while driving even if the vehicle proximity notifica- tion system is active.
Page 213 4-2. Driving procedures Hybrid transmission Shifting the shift lever While the power switch is in ON mode and the brake pedal depressed , shift the shift lever while pushing the shift release button on the shift knob. Shift the shift lever while pushing the shift release button on the shift knob.
Page 214 4-2. Driving procedures Shift position purpose Shift position Objective or function Parking the vehicle/starting the hybrid system Reversing Neutral Normal driving S mode driving (→P. 215) : To improve fuel efficiency and reduce noise, shift the shift lever to D for normal driving.
Page 215 4-2. Driving procedures Selecting the driving mode →P. 333 Changing shift ranges in S mode When the shift lever is in the S position, the shift lever or paddle shift switches (vehicles with 4.2-inch display) can be operated as follows: ...
Page 216 4-2. Driving procedures Selecting shift ranges in the D position (vehicles with paddle shift switches) To drive using temporary shift range selection, operate the “-” paddle shift switch. The shift range can then be selected by operating the “-” and “+” paddle shift switches. Changing the shift range allows restric- tion of the highest gear, preventing upshifting and enabling the level of engine braking force to be selected.
Page 217 If the shift lever cannot be shifted even though the brake pedal is depressed and the shift release button is pushed, there may be a problem with the shift lock system. Have the vehicle inspected by your Toyota dealer immediately. The following steps may be used as an emergency measure to ensure that the shift lever can be shifted.
Page 218 S This may indicate a malfunction in the automatic transmission system. Have the vehicle inspected by your Toyota dealer immediately. (In this situation, the transmission will operate in the same manner as when the shift lever is in D.) WARNING ■...
Page 219 4-2. Driving procedures Turn signal lever Operating instructions Right turn Lane change to the right (move the lever partway and release The right hand signals will flash 3 times. Lane change to the left (move the lever partway and release The left hand signals will flash 3 times.
Page 220 4-2. Driving procedures Parking brake A mode can be selected from the following modes. Automatic mode The parking brake is set or released automatically according to the shift lever operation. Even when in automatic mode, the parking brake can be set and released manually.
Page 221 4-2. Driving procedures Manual mode The parking brake can be set and released manually. Sets the parking brake The parking brake indicator light and parking brake light will turn on. Pull and hold the parking brake switch if an emergency occurs and it is necessary to operate the park- ing brake while driving.
Page 222 Operate the parking brake switch. If the message does not disappear after operating the switch several times, the system may be malfunctioning. Have the vehicle inspected by your Toyota dealer immediately. ■ Parking brake operation sound When the parking brake operates, a motor sound (whirring sound) may be heard.
Page 223 When the parking brake cannot be released due to a malfunction Driving the vehicle with the parking brake set will lead to brake components overheating, which may affect braking performance and increase brake wear. Contact your Toyota dealer immediately if this occurs.
Page 224 4-2. Driving procedures Brake Hold The brake hold system keeps the brake applied when the shift lever is in D, S or N with the system on and the brake pedal has been depressed to stop the vehicle. The system releases the brake when the accelerator pedal is depressed with the shift lever in D or S to allow smooth start off.
Page 225 Make sure that the parking brake indicator light goes off. (→P. 220) ■ When an inspection at your Toyota dealer is necessary When the brake hold standby indicator (green) does not illuminate even when the brake hold switch is pressed with the brake hold system operating condi- tions met, the system may be malfunctioning.
Page 226 4-2. Driving procedures WARNING ■ When the vehicle is on a steep incline When using the brake hold system on a steep incline, exercise caution. The brake hold function may not hold the vehicle in such a situation. ■ When stopped on a slippery road The system cannot stop the vehicle when the gripping ability of the tires has been exceeded.
Page 227 4-3. Operating the lights and wipers Headlight switch The headlights can be operated manually or automatically. Operating instructions Turning the end of the lever turns on the lights as follows: The headlights, day- time running lights (→P. 228) and all the lights listed below turn on and off automatically.
Page 228 4-3. Operating the lights and wipers AFS (Adaptive Front-lighting System) (if equipped) AFS (Adaptive Front-lighting System) secures excellent visibility at intersections and on curves by automatically adjusting the direction of the light axis of the headlights according to vehicle speed and the degree of the tire’s angle as controlled by steering input.
Page 229 4-3. Operating the lights and wipers ■ Automatic light off system ● When the headlights are on: The headlights and tail lights turn off 30 sec- onds after the power switch is turned to ACCESSORY mode or turned off and a door is opened and closed. (The lights turn off immediately if the key is pressed twice after all the doors are closed.) ●...
Page 230 4-3. Operating the lights and wipers Automatic High Beam The Automatic High Beam uses a camera sensor located behind the upper portion of the windshield to assess the brightness of the lights of vehicles ahead, streetlights, etc., and automatically turns the high beams on or off as necessary. WARNING ■...
Page 231 4-3. Operating the lights and wipers Turning the high beams on/off manually ■ Switching to the low beams Pull the lever to its original posi- tion. The Automatic High Beam indi- cator will turn off. Push the lever away from you to activate the Automatic High...
Page 232 4-3. Operating the lights and wipers ■ Conditions to turn the high beams on/off automatically ● When all of the following conditions are met, the high beams will be turned on automatically (after approximately 1 second): • The vehicle speed is approximately 21 mph (34 km/h) or more. •...
Page 233 4-3. Operating the lights and wipers ● In the following situations the system may not be able to correctly detect the surrounding brightness level. This may cause the low beams to remain on or the high beams to flash or dazzle pedestrians or vehicles ahead. In such a case, it is necessary to manually switch between the high and low beams.
Page 234: Washer
4-3. Operating the lights and wipers Windshield wipers and washer Operating the wiper lever The wiper operation is selected by moving the lever as follows. When intermittent windshield wiper operation is selected, the wiper interval can be also adjusted. Intermittent windshield wiper operation The intermittent wind-...
Page 235 Damage to the washer fluid pump may be caused if the lever is pulled toward you and held continually. ■ When a nozzle becomes blocked In this case, contact your Toyota dealer. Do not try to clear it with a pin or other object. The nozzle will be damaged.
Page 236 4-3. Operating the lights and wipers Changing the windshield wiper rest position/Lifting the wind- shield wipers When the windshield wipers are not being used, they retract to below the hood. To enable the windshield wipers to be lifted when parking in cold conditions or when replacing a windshield wiper insert, change the rest position of the windshield wipers to the service position using the wiper lever.
Page 237 4-3. Operating the lights and wipers ■ Lowering the windshield wipers to the retracted position With the windshield wipers placed on the windshield, turn the power switch to ON mode and then move the wiper lever to an operating position. When the wiper switch is turned off, the windshield wipers will stop at the retracted posi- tion.
Page 238 4-4. Refueling Opening the fuel tank cap Perform the following steps to open the fuel tank cap: Before refueling the vehicle ● Close all the doors and windows, and turn the power switch off. ● Confirm the type of fuel. (→P. 535) ■...
Page 239 4-4. Refueling WARNING ■ When refueling the vehicle Observe the following precautions while refueling the vehicle. Failure to do so may result in death or serious injury. ● After exiting the vehicle and before opening the fuel door, touch an unpainted metal surface to discharge any static electricity.
Page 240 4-4. Refueling Opening the fuel tank cap Press the opener to open the fuel filler door. Turn the fuel tank cap slowly to remove it and hang it on the back of the fuel filler door. Closing the fuel tank cap After refueling, turn the fuel tank cap until you hear a click.
Page 241 WARNING ■ When replacing the fuel tank cap Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.
Page 242: Toyota Safety Sense P
■ Toyota Safety Sense P The Toyota Safety Sense P is designed to operate under the assumption that the driver will drive safely, and is designed to help reduce the impact to the occupants and the vehicle in the case of a collision or assist the driver in normal driving conditions.
Page 243 Toyota will not disclose the recorded data to a third party except: • With the consent of the vehicle owner or with the consent of the lessee if the vehicle is leased •...
Page 244 4-5. Using the driving support systems Sensors Two types of sensors, located behind the front grille and windshield, detect information necessary to operate the drive assist systems. Radar sensor Camera sensor...
Page 245 Do not subject the radar sensor or surrounding area to a strong impact. If the radar sensor, front grille, or front bumper has been subjected to a strong impact, have the vehicle inspected by your Toyota dealer. ● Do not disassemble the radar sensor.
Page 246 ● Do not attach window tinting to the windshield. ● Replace the windshield if it is damaged or cracked. If the windshield needs to be replaced, contact your Toyota dealer. ● Do not get the camera sensor wet. ● Do not allow bright lights to shine into the camera sensor.
Page 247 ● Do not attach any accessories that may obstruct the camera sensor to the hood, front grille or front bumper. Contact your Toyota dealer for details. ● If a surfboard or other long object is to be mounted on the roof, make sure that it will not obstruct the camera sensor.
Page 248 4-5. Using the driving support systems ■ Certification  For vehicles sold in the U.S.A.  For vehicles sold in Canada...
Page 249 4-5. Using the driving support systems PCS (Pre-Collision System) The pre-collision system uses a radar sensor and camera sen- sor to detect vehicles and pedestrians in front of your vehicle. When the system determines that the possibility of a frontal col- lision with a vehicle or pedestrian is high, a warning operates to urge the driver to take evasive action and the potential brake pressure is increased to help the driver avoid the collision.
Page 250 4-5. Using the driving support systems WARNING ■ Limitations of the pre-collision system ● The driver is solely responsible for safe driving. Always drive safely, taking care to observe your surroundings. Do not use the pre-collision system instead of normal braking operations under any circumstances.
Page 251 4-5. Using the driving support systems WARNING ■ When to disable the pre-collision system In the following situations, disable the system, as it may not operate prop- erly, possibly leading to an accident resulting in death or serious injury: ● When the vehicle is being towed ●...
Page 252 4-5. Using the driving support systems Changing settings of the pre-collision system ■ Enabling/disabling the pre-collision system The pre-collision system can be enabled/disabled on (4.2-inch display) or (7-inch display) (→P. 105, 119) of the multi-informa- tion display. The system is automatically enabled each time the power switch is turned to ON mode.
Page 253 4-5. Using the driving support systems ■ Operational conditions The pre-collision system is enabled and the system determines that the pos- sibility of a frontal collision with a vehicle or pedestrian is high. Each function is operational at the following speeds: ●...
Page 254 4-5. Using the driving support systems ■ Conditions under which the system may operate even if there is no pos- sibility of a collision ● In some situations such as the following, the system may determine that there is a possibility of a frontal collision and operate. •...
Page 255 4-5. Using the driving support systems • When there is a metal object (manhole cover, steel plate, etc.), steps, or a protrusion on the road surface or roadside • When crossing pedestrian approaches very close to the vehicle • When passing through a place with a low structure above the road (low ceil- ing, traffic sign, etc.) •...
Page 256 4-5. Using the driving support systems ■ Situations in which the system may not operate properly ● In some situations such as the following, a vehicle may not be detected by the radar sensor and camera sensor, preventing the system from operating properly: •...
Page 257 4-5. Using the driving support systems • When a very bright light, such as the sun or the headlights of oncoming traffic, shines directly into the camera sensor • When the surrounding area is dim, such as at dawn or dusk, or while at night or in a tunnel •...
Page 258 ● If the PCS warning light continues to flash or illuminate or the warning mes- sage does not disappear, the system may be malfunctioning. Have the vehi- cle inspected by your Toyota dealer immediately.
Page 259 4-5. Using the driving support systems ■ If VSC is disabled ● If VSC is disabled (→P. 284), the pre-collision brake assist and pre-collision braking functions are also disabled. ● The PCS warning light will turn on and “VSC Turned Off Pre-Collision Brake System Unavailable”...
Page 260 4-5. Using the driving support systems LDA (Lane Departure Alert with steering control) Summary of functions When driving on highways and freeways with white (yellow) lines, this function alerts the driver when the vehicle might depart from its lane and provides assistance by operating the steering wheel to keep the vehicle in its lane.
Page 261 4-5. Using the driving support systems Functions included in LDA system ◆ Lane departure alert function When the system determines that the vehicle might depart from its lane, a warning is dis- played on the multi-information display and the warning buzzer sounds to alert the driver.
Page 262 4-5. Using the driving support systems ◆ Vehicle sway warning function When the vehicle is swaying or appears as if it may depart from its lane multiple times, the warning buzzer sounds and a message is displayed on the multi-information display to alert the driver.
Page 263 Do not modify the suspension etc. If the suspension etc. needs to be replaced, contact your Toyota dealer. ● Do not install or place anything on the hood or grille. Also, do not install a grille guard (bull bars, kangaroo bar, etc.). ● If your windshield needs repairs, contact your Toyota dealer.
Page 264 4-5. Using the driving support systems Turning LDA system on Press the LDA switch to turn the LDA system on. The LDA indicator illuminates and a message is displayed on the multi-information display. Press the LDA switch again to turn the LDA system off.
Page 265 4-5. Using the driving support systems Indications on multi-information display The illustration used is intended as an example, and may differ from the image that is actually displayed on the multi-information display. LDA indicator The illumination condition of the indicator informs the driver of the system operation status.
Page 266 4-5. Using the driving support systems ■ Operation conditions of each function ● Lane departure alert function This function operates when all of the following conditions are met. • LDA is turned on. • Vehicle speed is approximately 32 mph (50 km/h) or more. •...
Page 267 4-5. Using the driving support systems ■ Temporary cancellation of functions When operation conditions are no longer met, a function may be temporarily canceled. However, when the operation conditions are met again, operation of the function is automatically restored. (→P. 266) ■...
Page 268 4-5. Using the driving support systems ■ Conditions in which functions may not operate properly In the following situations, the camera sensor may not detect white (yellow) lines and various functions may not operate normally. ● There are shadows on the road that run parallel with, or cover, the white (yellow) lines.
Page 269 4-5. Using the driving support systems ■ If the LDA indicator is illuminated in yellow and a warning message is displayed on the multi-information display →P. 481 ■ Customization Some functions can be customized. (→P. 105, 119)
Page 270 4-5. Using the driving support systems Dynamic radar cruise control with full- speed range Summary of functions In vehicle-to-vehicle distance control mode, the vehicle automatically accelerates, decelerates and stops to match the speed changes of the preceding vehicle even if the accelerator pedal is not depressed. In constant speed control mode, the vehicle runs at a fixed speed.
Page 271 4-5. Using the driving support systems WARNING ■ Before using dynamic radar cruise control with full-speed range Driving safely is the sole responsibility of the driver. Do not rely solely on the system, and drive safely by always paying careful attention to your sur- roundings.
Page 272 4-5. Using the driving support systems WARNING ■ To avoid inadvertent dynamic radar cruise control with full-speed range activation Switch the dynamic radar cruise control with full-speed range off using the cruise control main switch when not in use. ■ Situations unsuitable for dynamic radar cruise control with full-speed range Do not use dynamic radar cruise control with full-speed range in any of the...
Page 273 4-5. Using the driving support systems Driving in vehicle-to-vehicle distance control mode This mode employs a radar sensor to detect the presence of vehicles up to approximately 328 ft. (100 m) ahead, determines the current vehicle-to-vehicle following distance, and operates to maintain a suit- able following distance from the vehicle ahead.
Page 274 4-5. Using the driving support systems Example of acceleration When there are no longer any preceding vehicles driving slower than the set speed The system accelerates until the set speed is reached. The system then returns to constant speed cruising. Setting the vehicle speed (vehicle-to-vehicle distance control mode) Press the cruise control main...
Page 275 4-5. Using the driving support systems Adjusting the set speed To change the set speed, operate the “+ RES” or “- SET” switch until the desired set speed is displayed. Increases the speed (Except when the vehicle has been stopped by system control in vehi- cle-to-vehicle distance control...
Page 276 4-5. Using the driving support systems Changing the vehicle-to-vehicle distance (vehicle-to-vehicle dis- tance control mode) Pressing the switch changes the Preceding vehicle-to-vehicle distance as fol- vehicle mark lows: Long Medium Short The vehicle-to-vehicle distance is set automatically to long mode when the power switch is turned to ON mode.
Page 277 4-5. Using the driving support systems Resuming follow-up cruising when the vehicle has been stopped by system control (vehicle-to-vehicle distance control mode) After the vehicle ahead of you starts off, press the “+ RES” switch. Your vehicle will also resume fol- low-up cruising if the accelerator pedal is depressed after the vehi- cle ahead of you starts off.
Page 278 4-5. Using the driving support systems Approach warning (vehicle-to-vehicle distance control mode) When your vehicle is too close to a vehicle ahead, and sufficient automatic deceleration via the cruise control is not possible, the display will flash and the buzzer will sound to alert the driver.
Page 279 4-5. Using the driving support systems Selecting constant speed control mode When constant speed control mode is selected, your vehicle will main- tain a set speed without controlling the vehicle-to-vehicle distance. Select this mode only when vehicle-to-vehicle distance control mode does not function correctly due to a dirty radar sensor, etc.
Page 280 • The driver’s door is opened. • The vehicle has been stopped for about 3 minutes If vehicle-to-vehicle distance control mode is automatically canceled for any other reason, there may be a malfunction in the system. Contact your Toyota dealer.
Page 281 Pre-collision braking is activated. If constant speed control mode is automatically canceled for any other rea- son, there may be a malfunction in the system. Contact your Toyota dealer. ■ Warning messages and buzzers for dynamic radar cruise control with...
Page 282 4-5. Using the driving support systems ● Motorcycles traveling in the same lane ● When water or snow thrown up by the surrounding vehicles hinders the detecting of the sensor ● When your vehicle is pointing upwards (caused by a heavy load in the luggage compartment, etc.) ●...
Page 283 4-5. Using the driving support systems Driving assist systems To keep driving safety and performance, the following systems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehi- cle.
Page 284 4-5. Using the driving support systems ◆ Hill-start assist control Helps to reduce the backward movement of the vehicle when start- ing on an uphill ◆ EPS (Electric Power Steering) Employs an electric motor to reduce the amount of effort needed to turn the steering wheel ◆...
Page 285 When the message is displayed on the multi-information display show- ing that TRAC has been disabled even if has not been pressed TRAC cannot be operated. Contact your Toyota dealer. ■ Operating conditions of hill-start assist control When the following four conditions are met, the hill-start assist control will operate: ●...
Page 286 4-5. Using the driving support systems ■ Sounds and vibrations caused by the ABS, brake assist, VSC, TRAC, and hill-start assist control systems ● A sound may be heard from the engine compartment when the brake pedal is depressed repeatedly, when the hybrid system is started or just after the vehicle begins to move.
Page 287 4-5. Using the driving support systems ■ Automatic reactivation of TRAC and VSC systems After turning the TRAC and VSC systems off, the systems will be automati- cally re-enabled in the following situations: ● When the power switch is turned off ●...
Page 288 4-5. Using the driving support systems WARNING ■ The ABS does not operate effectively when ● The limits of tire gripping performance have been exceeded (such as excessively worn tires on a snow covered road). ● The vehicle hydroplanes while driving at high speed on wet or slick roads. ■...
Page 289 The ABS, TRAC and VSC systems will not function correctly if different tires are installed on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels. ■ Handling of tires and the suspension Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause a system to malfunction.
Page 290 4-5. Using the driving support systems BSM (Blind Spot Monitor) ∗ Summary of the Blind Spot Monitor The Blind Spot Monitor is a system that has 2 functions; ● The BSM (Blind Spot Monitor) function Assists the driver in making a decision when changing lanes ●...
Page 291 4-5. Using the driving support systems Audio system screen (RCTA function only) If a vehicle approaching from the right or left at the rear of the vehicle is detected, the RCTA icon (→P. 296, 300) for the detected side will be dis- played.
Page 292 4-5. Using the driving support systems ■ Certification for the Blind Spot Monitor  For vehicles sold in the U.S.A.  For vehicles sold in Canada...
Page 293 Do not modify the sensor or surrounding area on the bumper. ● Do not paint the rear bumper any color other than an official Toyota color. BSM function The BSM function uses radar sensors to detect vehicles that are trav-...
Page 294 4-5. Using the driving support systems BSM function detection areas The areas that vehicles can be detected in are outlined below. The range of the detection area extends to: Approximately 11.5 ft. (3.5 m) from the side of the vehicle The first 1.6 ft.
Page 295 4-5. Using the driving support systems ● Guardrails, walls, signs, parked vehicles and similar stationary objects ● Following vehicles that are in the same lane ● Vehicles driving 2 lanes across from your vehicle : Depending on the conditions, detection of a vehicle and/or object may occur.
Page 296 RCTA icon display (if equipped) When a vehicle approaching from the right or left at the rear of the vehicle is detected, the following will be displayed on the audio sys- tem screen. Toyota parking Panoramic view Content assist monitor...
Page 297 4-5. Using the driving support systems WARNING ■ Cautions regarding the use of the system The driver is solely responsible for safe driving. Always drive safely, taking care to observe your surroundings. The RCTA function is only an assist and is not a replacement for careful driving.
Page 298 4-5. Using the driving support systems RCTA function detection areas The areas that vehicles can be detected in are outlined below. To give the driver a more consistent time to react, the buzzer can alert for faster vehicles from farther away. Example: Approximate Approaching vehicle...
Page 299 4-5. Using the driving support systems ■ Conditions under which the RCTA function may not function correctly ● The RCTA function may not detect vehicles correctly in the following condi- tions: • When the sensor is misaligned due to a strong impact to the sensor or its surrounding area •...
Page 300 If a pedestrian is detected, a buzzer will sound and an icon on the audio system screen will be displayed to inform the driver of the pedestrian. Display Toyota parking assist monitor Panoramic view monitor   Pedestrian detection icon Displayed automatically when a pedestrian is detected.
Page 301 If the rear camera detection function is malfunctioning If a malfunction of the rear camera detection function is detected, one of the following messages will be displayed on the audio system screen. Have the vehicle inspected by your Toyota dealer. ● “RCD malfunction.”...
Page 302 4-5. Using the driving support systems ■ Situations in which the system may not operate properly ● Some pedestrians, such as the following, may not be detected by the Rear Camera Detection function, preventing the function from operating properly: • Pedestrians who are squatting •...
Page 303 4-5. Using the driving support systems • If the orientation of the rear camera has been changed due to a collision or other impact, or removal and installation • If a towing eyelet is installed to the rear of the vehicle •...
Page 304 4-5. Using the driving support systems ∗ Intuitive parking assist The distance from your vehicle to nearby obstacles when paral- lel parking or maneuvering into a garage is measured by the sensors and communicated via the displays and a buzzer. Always check the surrounding area when using this system.
Page 305 4-5. Using the driving support systems Display When the sensors detect an obstacle, the following displays inform the driver of the position and distance to the obstacle. ■ Multi-information display Front corner sensor opera- tion Front center sensor opera- tion Rear corner sensor operation Rear center sensor operation Select to mute the buzzer...
Page 306 4-5. Using the driving support systems Sensor detection display, obstacle distance ■ Distance display Sensors that detect an obstacle will illuminate continuously or blink. Insert display Approximate distance to obstacle Multi- Toyota Pan- informa- parking oramic Front and rear Front and rear tion dis-...
Page 307 4-5. Using the driving support systems ■ Buzzer operation and distance to an obstacle A buzzer sounds when the sensors are operating. ● The buzzer sounds faster as the vehicle approaches an obstacle. When the vehicle comes within the following distance of the obstacle, the buzzer sounds continuously: Approximately 1.2 ft.
Page 308 ■ Intuitive parking assist display When an obstacle is detected while the Toyota parking assist monitor or pan- oramic view monitor is in use, the warning indicator will appear in the upper part of the screen even if the display setting has been set to off.
Page 309 4-5. Using the driving support systems ■ Sensor detection information ● The sensor’s detection areas are limited to the areas around the vehicle’s bumper. ● Depending on the shape of the obstacle and other factors, the detection dis- tance may shorten, or detection may be impossible. ●...
Page 310 The area directly under the bumpers is not detected. ● If obstacles draw too close to the sensor. ● A non-genuine Toyota suspension (lowered suspension, etc.) is installed. ● A backlit license plate is installed. In addition to the examples above, there are instances in which, because of their shape, signs and other objects may be judged by a sensor to be closer than they are.
Page 311 When using intuitive parking assist In the following situations, the system may not function correctly due to a sensor malfunction, etc. Have the vehicle checked by your Toyota dealer. ● The intuitive parking assist operation display flashes, and a buzzer sounds when no obstacles are detected.
Page 312 4-5. Using the driving support systems ∗ Intelligent Clearance Sonar (ICS) If a collision with an object may occur due to the vehicle sud- denly moving forward due to an accidental accelerator pedal operation, the vehicle moving the unintended direction due to the wrong shift position being selected, or while parking or trav- eling at low speeds, the sensors detect objects, such as a wall, in the traveling direction of the vehicle, and the system operates...
Page 313 4-5. Using the driving support systems ◆ When the accelerator pedal is depressed excessively ◆ When the vehicle moves in the unintended direction due to the wrong shift position being selected...
Page 314 4-5. Using the driving support systems Rear Cross Traffic Auto Brake function If a radar sensor detects a vehicle approaching from the right or left at the rear of the vehicle and a collision may occur, this function will per- form brake control to reduce the likelihood of an impact with the approaching vehicle.
Page 315 4-5. Using the driving support systems Types of sensors Front corner sensors Front center sensors Rear corner sensors Rear center sensors Turning the Intelligent Clearance Sonar system on/off Press of the meter con- trol switches, select Press of the meter con- trol switches, select Press of the meter con-...
Page 316 4-5. Using the driving support systems Displays and buzzers for hybrid system output restriction con- trol and brake control If the hybrid system output restriction control or brake control oper- ates, a buzzer will sound and a message will be displayed on the multi-information display to alert the driver.
Page 317 4-5. Using the driving support systems Intelligent Clearance Sonar function If the Intelligent Clearance Sonar function detects that a collision with an object is possible, the hybrid system output will be restricted to restrain any increase in the vehicle speed. (Hybrid system output restriction control: See A below.) Additionally, if the accelerator pedal continues to be depressed, the brakes will be applied automatically to reduce the vehicle speed.
Page 318 4-5. Using the driving support systems Time Down Time Down Time Accelerator pedal Start of control Brake pedal High possibility of a collision Hybrid system output Extremely high possibility of a collision Braking force...
Page 319 4-5. Using the driving support systems ■ The Intelligent Clearance Sonar function will operate when The function will operate when the ICS OFF indicator is not illuminated or flashing (→P. 315, 323) and all of the following conditions are met: ●...
Page 320 4-5. Using the driving support systems ■ Re-enabling the Intelligent Clearance Sonar system To re-enable the Intelligent Clearance Sonar system when it is disabled due to operation of the Intelligent Clearance Sonar function, either enable the sys- tem again (→P. 315), or turn the power switch off and then back to ON mode. Additionally, if the object becomes no longer in the traveling direction of the vehicle or if the traveling direction of the vehicle changes (such as changing from moving forward to backing up, or from backing up to moving forward),...
Page 321 4-5. Using the driving support systems ■ Situations in which the Intelligent Clearance Sonar function may operate even if there is no possibility of a collision In some situations such as the following, the Intelligent Clearance Sonar function may operate even though there is no possibility of a collision. ●...
Page 322 4-5. Using the driving support systems ● Changes in the vehicle posture • If the vehicle is significantly tilted • If the front of the vehicle is raised or lowered due to the carried load • If the orientation of a sensor has been changed due to a collision or other impact ■...
Page 323 If this message continues to be displayed even after cleaning the sensor, or is displayed even though the sensor is clean, have the vehicle inspected by your Toyota dealer. ● Initialization may not have been performed after a 12-volt battery terminal...
Page 324 4-5. Using the driving support systems WARNING ■ Limitations of the Intelligent Clearance Sonar system Do not overly rely on the system, as doing so may lead to an accident. ● The driver is solely responsible for safe driving. Always drive carefully, tak- ing care to observe your surroundings.
Page 325 If the area around a sensor is subjected to an impact, the system may not operate properly due to the sensor being misaligned. Have the vehicle inspected by your Toyota dealer. ● When using a high pressure washer to wash the vehicle, do not spray the sensors directly, as doing so may cause a sensor to malfunction.
Page 326 4-5. Using the driving support systems Rear Cross Traffic Auto Brake function If the Rear Cross Traffic Auto Brake function detects that a collision with an approaching vehicle is possible, the hybrid system output will be restricted to restrain any increase in vehicle speed. (Hybrid system output restriction control: See A below.) Additionally, if the accelerator pedal continues to be depressed, the brakes will be applied automatically to reduce the vehicle speed.
Page 327 4-5. Using the driving support systems Time Down Time Down Time Accelerator pedal Start of control Brake pedal High possibility of a collision Hybrid system output Extremely high possibility of a collision Braking force...
Page 328 4-5. Using the driving support systems ■ The Rear Cross Traffic Auto Brake function will operate when The function will operate when the ICS OFF indicator is not illuminated or flashing (→P. 315, 323) and all of the following conditions are met: ●...
Page 329 4-5. Using the driving support systems ■ Re-enabling the Rear Cross Traffic Auto Brake function To re-enable the Rear Cross Traffic Auto Brake function when it is disabled while it is operating, either enable the Intelligent Clearance Sonar system again (→P. 315), or turn the power switch off and then back to ON mode. When the function is disabled, the ICS OFF indicator will illuminate.
Page 330 4-5. Using the driving support systems ■ Situations in which the system may operate even though there is no possibility of a collision In some situations such as the following, the Rear Cross Traffic Auto Brake function may operate even though there is no possibility of a collision. ●...
Page 331 4-5. Using the driving support systems ■ Situations in which the Rear Cross Traffic Auto Brake function may not operate properly In some situations such as the following, this function may not operate prop- erly. ● Objects and vehicles which the radar sensors are not designed to detect •...
Page 332 4-5. Using the driving support systems • When backing out of a shallow angle parking spot • Vehicles that the sensors cannot detect due to obstructions • When backing up on a slope with a sharp change in grade • When a vehicle turns into the detec- tion area ■...
Page 333 4-5. Using the driving support systems Driving mode select switches The driving modes can be selected to suit driving condition. Normal mode Use for normal driving. While in Eco drive mode or sport mode, press the switch to change the driving mode to normal mode.
Page 334 4-5. Using the driving support systems ■ Operation of the air conditioning system in Eco drive mode Eco drive mode controls the heating/cooling operations and fan speed of the air conditioning system to enhance fuel efficiency (→P. 344). To improve air conditioning performance, adjust the fan speed or turn off Eco drive mode.
Page 335 4-6. Driving tips Hybrid vehicle driving tips For economical and ecological driving, pay attention to the fol- lowing points: ◆ Using Eco drive mode When using Eco drive mode, the torque corresponding to the accel- erator pedal depression amount can be generated more smoothly than it is in normal conditions.
Page 336 4-6. Driving tips ◆ When braking Make sure to operate the brakes gently and in a timely manner. A greater amount of electrical energy can be regenerated when slow- ing down. ◆ Delays Repeated acceleration and deceleration, as well as long waits at traffic lights, will lead to bad fuel economy.
Page 337 4-6. Driving tips ◆ Luggage Carrying heavy luggage will lead to poor fuel economy. Avoid carry- ing unnecessary luggage. Installing a large roof rack will also cause poor fuel economy. ◆ Warming up before driving Since the gasoline engine starts up and cuts out automatically when cold, warming up the engine is unnecessary.
Page 338 4-6. Driving tips Winter driving tips Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a man- ner appropriate to the prevailing weather conditions. Preparation for winter ● Use fluids that are appropriate to the prevailing outside tempera- tures.
Page 339 If the shift lever can be shifted from P, there may be a problem with the shift lock system. Have the vehicle inspected by your Toyota dealer immediately. Selecting tire chains Vehicles with 16 and 17-inch tires ...
Page 340 4-6. Driving tips Regulations on the use of tire chains Regulations regarding the use of tire chains vary depending on loca- tion and type of road. Always check local regulations before installing chains. ■ Tire chain installation Observe the following precautions when installing and removing chains: ●...
Page 341 NOTICE ■ Repairing or replacing snow tires Request repairs or replacement of snow tires from Toyota dealers or legiti- mate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.
Page 342 4-6. Driving tips...
Page 343: Interior Features
Interior features 5-1. Using the air 5-4. Other interior features conditioning system Other interior features ..364 and defogger • Sun visors ..... 364 Automatic air conditioning • Vanity mirrors....364 system......344 • Power outlet....365 Seat heaters...... 353 •...
Page 344: Conditioning System
5-1. Using the air conditioning system and defogger Automatic air conditioning system Air outlets and fan speed are automatically adjusted according to the temperature setting. Air conditioning controls  Type A Type B ...
Page 345 5-1. Using the air conditioning system and defogger ■ Adjusting the temperature setting To adjust the temperature setting, turn clockwise to increase the temperature and counterclockwise to decrease the tempera- ture. The air conditioning system switches between individual and synchro- nized modes each time is pressed.
Page 346 5-1. Using the air conditioning system and defogger ■ Change the airflow mode To change the airflow mode, press outlets used switched each time the button is pressed. Air flows to the upper body. Air flows to the upper body and feet.
Page 347 5-1. Using the air conditioning system and defogger Manual S-FLOW mode  When is pressed, S-FLOW mode will be manually enabled/ disabled. indicator will illuminate when S-FLOW mode is enabled. Using automatic mode Press The dehumidification function begins to operate. Air outlets and fan speed are automatically adjusted according to the temperature set- ting.
Page 348 5-1. Using the air conditioning system and defogger Other functions ■ Switching between outside air and recirculated air modes Press The mode switches between outside air mode (indicator off) and recir- culated air mode (indicator on) each time is pressed. ■...
Page 349 5-1. Using the air conditioning system and defogger Air outlets ■ Location of air outlets The air outlets and air volume change according selected airflow mode. : If equipped ■ Adjusting the position of and opening and closing the air out- lets ...
Page 350 5-1. Using the air conditioning system and defogger ■ Using automatic mode Fan speed is adjusted automatically according to the temperature setting and the ambient conditions. Therefore, the fan may stop for a while until warm or cool air is ready to flow immediately after is pressed.
Page 351 5-1. Using the air conditioning system and defogger ■ When the outside temperature exceeds 75°F (24°C) and the air condition- ing system is on ● In order to reduce the air conditioning power consumption, the air condition- ing system may switch to recirculated air mode automatically. This may also reduce fuel consumption.
Page 352 5-1. Using the air conditioning system and defogger WARNING ■ To prevent the windshield from fogging up ● Do not use during cool air operation in extremely humid weather. The difference between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog up, block- ing your vision.
Page 353: Seat Heaters
5-1. Using the air conditioning system and defogger Seat heaters WARNING ● Care should be taken to prevent injury if anyone in the following categories comes in contact with the seats when the heater is on: • Babies, small children, the elderly, the sick and the physically chal- lenged •...
Page 354: Using The Interior Lights Interior Lights List
5-2. Using the interior lights Interior lights list Front interior/personal lights (→P. 355, 356) Shift lever light (if equipped) Inside door handle lights (if equipped) Rear interior light (if equipped) (→P. 355) Rear personal lights (if equipped) (→P. 356) Door courtesy lights Instrument panel ornament light (if equipped) Front center console light (if equipped) Footwell lights (if equipped)
Page 355: Interior Lights
5-2. Using the interior lights Interior lights ■ Front (if equipped) The rear personal lights (if equipped) turn on/off together with the front interior light. Turns the lights on/off linked to door positions Turns the lights on/off ■ Rear (if equipped) Turns the light off Turns the light on/off linked to door positions...
Page 356: Personal Lights
5-2. Using the interior lights Personal lights ■ Front Turns the lights on/off ■ Rear (if equipped) Turns the lights on/off ● Illuminated entry system: The lights automatically turn on/off according to the power switch mode, the presence of the electronic key, whether the doors are locked/unlocked, and whether the doors are open/closed.
Page 357 5-3. Using the storage features List of storage features Auxiliary boxes (→P. 361) Console box (→P. 358) Glove box (→P. 358) Auxiliary box/open tray (→P. 361, 362) Bottle holders/door pockets (→P. 359) Coin holder (→P. 358) Cup holders (→P. 360) WARNING ●...
Page 358: Glove Box
5-3. Using the storage features Glove box Unlock with the mechanical key Lock with the mechanical key Open (pull lever) The glove box light turns on when the tail lights are on. Console box Push the knob. Coin holder Pull the lever to open.
Page 359: Bottle Holders
5-3. Using the storage features Bottle holders Front Rear   ● When storing a bottle, close the cap. ● The bottle may not be stored depending on its size or shape. WARNING Do not place anything other than a bottle in the bottle holders. Other items may be thrown out of the holders in the event of an accident or sudden braking and cause injury.
Page 360: Cup Holders
5-3. Using the storage features Cup holders Front Rear   Pull the armrest down. WARNING ● Do not place anything other than cups or aluminum cans in the cup hold- ers. Other items may be thrown out of the holders in the event of an acci- dent or sudden braking, causing injury.
Page 361: Auxiliary Boxes
5-3. Using the storage features Auxiliary boxes Type A (if equipped) Type B (if equipped)   Push the lid.  Type C Opening: Push the tray forward until it locks. Closing: Push the tray forward to release the lock and the tray will automati- cally close.
Page 362: Open Tray
5-3. Using the storage features WARNING ■ Items unsuitable for storing (type A) Do not store items heavier than 0.4 lb. (0.2 kg). Doing so may cause the auxiliary box to open and the items inside may fall out, resulting in an accident. NOTICE ■...
Page 363: Trunk Features
5-3. Using the storage features Trunk features Grocery bag hooks NOTICE To prevent damage to the hooks, do not apply too much load to the hooks.
Page 364: Other Interior Features Other Interior Features
5-4. Other interior features Other interior features Sun visors To set the visor in the forward position, flip it down. To set the visor in the side posi- tion, flip down, unhook, and swing it to the side. To use the side extender, place the visor in the side position, then slide it backward.
Page 365: Power Outlet
5-4. Other interior features Power outlet Please use as a power supply for electronic goods that use less than 12 VDC/10 A (power consumption of 120 W). Open the lid. The power outlet can be used when the power switch is in ACCESSORY or ON mode.
Page 366: Usb Charging Ports
5-4. Other interior features USB charging ports (if equipped) The USB charging ports are used to supply 2.1 A of electricity at 5 V to external devices. The USB charging ports are for charging only. They are not designed for data transfer or other purposes. Depending on the external device, it may not charge properly.
Page 367 5-4. Other interior features NOTICE ■ To prevent damage to the USB charging ports ● Do not insert foreign objects into the ports. ● Do not spill water or other liquids into the ports. ● When the USB charging ports are not in use, close the lids. If a foreign object or liquid enters a port may cause a short circuit.
Page 368: Wireless Charger
5-4. Other interior features Wireless charger (if equipped) A portable device, such as a smartphone or mobile battery, can be charged by just placing it on the charging area, provided the device is compatible with the Qi wireless charging standard created by the Wireless Power Consortium.
Page 369 5-4. Other interior features ■ Using the wireless charger Press power supply switch of the wireless char- ger. Pressing the switch again turns the wireless charger off. When turned on, the operation indicator light (green) comes on. When the power switch is turned off, the on/off state of the wire- less charger will be memorized.
Page 370 (orange). Take the appropriate measures according to the table below. Operation indicator light Suspected causes Measure Blinks (orange) at a Vehicle to charger com- Contact your Toyota second interval munication failure. dealer. continuously A foreign object exists between the portable...
Page 371 5-4. Other interior features ■ The wireless charger can be operated when The power switch is in ACCESSORY or ON mode. ■ Portable devices that can be charged ● Portable devices compatible with the Qi wireless charging standard can be charged by the wireless charger.
Page 372 5-4. Other interior features ■ Certification for the wireless charger...
Page 373 5-4. Other interior features...
Page 374 5-4. Other interior features...
Page 375 5-4. Other interior features WARNING ■ Caution while driving When charging a portable device while driving, for safety reasons, the driver should not operate the portable device. ■ Caution regarding interference with electronic devices People with implantable cardiac pacemakers, cardiac resynchronization therapy pacemakers or implantable cardioverter defibrillators, as well as any other electrical medical device, should consult their physician about the usage of the wireless charger.
Page 376 If in situations other than above the wireless charger does not operate prop- erly or the operation indicator light is blinking, the wireless charger may be malfunctioning. Contact your Toyota dealer. ■ To prevent failure or damage to data ●...
Page 377: Armrest
5-4. Other interior features Armrest Fold down the armrest for use. NOTICE To prevent damage to the armrest, do not apply too much load on the arm- rest. Assist grips An assist grip installed on the ceil- ing can be used to support your body while sitting on the seat.
Page 378: Coat Hooks
5-4. Other interior features Coat hooks Coat hooks are provided on the rear assist grips. WARNING Do not hang coat hangers or other hard or sharp objects on the hook. If the SRS curtain shield airbags deploy, these items may become projectiles, causing death or serious injury.
Page 379: Garage Door Opener
5-4. Other interior features ∗ Garage door opener The garage door opener can be programmed to operate garage doors, gates, entry doors, door locks, home lighting systems, security systems, and other devices. ® HomeLink ® The HomeLink wireless control system in your vehicle has 3 buttons which can be programmed to operate 3 different devices.
Page 380 5-4. Other interior features ® ■ Programming the HomeLink Steps through must be performed within 60 seconds, other- wise the indicator light will stop flashing and programming will not be able to be completed. ® Press and release the HomeLink button you want to program ®...
Page 381 5-4. Other interior features ® Test the HomeLink operation by pressing the newly pro- grammed button and observing the indicator light: ● Indicator light illuminates: Programming of a fixed code device has completed. The garage door or other device should operate ®...
Page 382 5-4. Other interior features Press and hold the desired ® HomeLink button (inside the vehicle) for 2 seconds and release Repeat this sequence (press/hold/ release) up to 3 times to complete programming. If the garage door opener motor operates when the ®...
Page 383 5-4. Other interior features ® ■ Reprogramming a single HomeLink button When the following procedure is performed, buttons which already have devices registered to them can be overwritten: ® With one hand, press and hold the desired HomeLink button. ® When the HomeLink indicator starts flashing orange, continue ®...
Page 384 5-4. Other interior features ® Erasing the entire HomeLink memory (all three codes) Press and hold the 2 outside but- tons for 10 seconds until the ® HomeLink indicator light changes from continuously lit orange to rapidly flashing green. If you sell your vehicle, be sure to erase the programs stored in the ®...
Page 385 5-4. Other interior features ■ When support is necessary Visit on the web at www.homelink.com/toyota or call 1-800-355-3515. WARNING ■ When programming a garage door or other remote control device The garage door or other device may operate, so ensure people and objects are out of danger to prevent potential harm.
Page 386: Safety Connect
Telematics Subscription Service Agreement and its Terms and Conditions, as in effect and amended from time to time, a current copy of which is available at Toyota.com. All use of the Safety Connect service is subject to such then-applicable Terms and Conditions.
Page 387 A variety of subscription terms are available for purchase. Contact your Toyota dealer, call the Safety Connect response center at 1- 855-405-6500, or push the “SOS” button in your vehicle for further subscription details.
Page 388 ● Green indicator light flashing = Safety Connect call in process ● Red indicator light (except at vehicle start-up) = System malfunction (contact your Toyota dealer) ● No indicator light (off) = Safety Connect service not active Safety Connect services ■...
Page 389 In addition to assisting law enforcement with recovery of a stolen vehicle, Safety-Connect-equipped vehicle location data may, under certain circumstances, be shared with third parties to locate your vehicle. Further information is available at Toyota.com. ■ Emergency Assistance Button (“SOS”) In the event of an emergency on the road, push the “SOS”...
Page 390 5-4. Other interior features Safety information for Safety Connect Important! Read this information before using Safety Connect. ■ Exposure to radio frequency signals The Safety Connect system installed in your vehicle is a low-power radio transmitter and receiver. It receives and also sends out radio frequency (RF) signals.
Page 391 5-4. Other interior features ■ Certification for Safety Connect...
Page 392: Compass
5-4. Other interior features ∗ Compass The compass on the inside rear view mirror indicates the direc- tion in which the vehicle is heading. Operation To turn the compass on or off, press and hold the button for 3 seconds. Displays and directions Display Direction...
Page 393 5-4. Other interior features Calibrating the compass The direction display deviates from the true direction determined by the earth’s magnetic field. The amount of deviation varies according to the geographic position of the vehicle. If you cross over a map boundary shown in illustration, the compass will deviate.
Page 394 5-4. Other interior features ■ Circling calibration Stop the vehicle in a place where it is safe to drive in a circle. Press and hold the button for 9 seconds. “C” appears on the compass display. Drive the vehicle at 5 mph (8 km/h) or less in a circle until a direction is displayed.
Page 395 5-4. Other interior features WARNING ■ While driving the vehicle Do not adjust the display. Adjust the display only when the vehicle is stopped. ■ When doing the circling calibration Secure a wide space, and watch out for people and vehicles in the neigh- borhood.
Page 396 5-4. Other interior features...
Page 397 Maintenance and care 6-1. Maintenance and care 6-3. Do-it-yourself maintenance Cleaning and protecting the vehicle exterior..398 Do-it-yourself service precautions ..... 412 Cleaning and protecting the vehicle interior... 401 Hood ......... 414 Positioning a floor jack ..415 6-2. Maintenance Engine compartment..
Page 398: The Vehicle Exterior
6-1. Maintenance and care Cleaning and protecting the vehicle exterior Perform the following to protect the vehicle and maintain it in prime condition: ● Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust.
Page 399 ■ Precaution regarding the rear bumper with Blind Spot Monitor (if equipped) If the paint of the rear bumper is chipped or scratched, the system may mal- function. If this occurs, avoid using the system and consult your Toyota dealer.
Page 400 6-1. Maintenance and care NOTICE ■ To prevent paint deterioration and corrosion on the body and compo- nents (aluminum wheels, etc.) ● Wash the vehicle immediately in the following cases: • After driving near the sea coast • After driving on salted roads •...
Page 401: Cleaning And Protecting The Vehicle Interior
6-1. Maintenance and care Cleaning and protecting the vehicle interior The following procedures will help protect your vehicle’s interior and keep it in top condition: Protecting the vehicle interior ● Remove dirt and dust using a vacuum cleaner. Wipe dirty surfaces with a cloth dampened with lukewarm water.
Page 402 6-1. Maintenance and care ■ Caring for leather areas Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle's interior. ■ Shampooing the carpets There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam.
Page 403 6-1. Maintenance and care NOTICE ■ Cleaning detergents ● Do not use the following types of detergent, as they may discolor the vehi- cle interior or cause streaks or damage to painted surfaces: • Areas other than the seats and steering wheel: Organic substances such as benzene or gasoline, alkaline or acidic solutions, dye, and bleach •...
Page 404: Maintenance Requirements
Toyota recommends the following main- tenance: General maintenance General maintenance should be performed on a daily basis. This can be done by yourself or by a Toyota dealer. Scheduled maintenance Scheduled maintenance should be performed at specified intervals according to the maintenance schedule.
Page 405 ■ Repair and replacement It is recommended that genuine Toyota parts be used for repairs to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than a Toyota dealer performs repairs, confirm the war- ranty coverage.
Page 406 6-2. Maintenance WARNING ■ If your vehicle is not properly maintained Improper maintenance could result in serious damage to the vehicle and possible death or serious injury. ■ Important health and safety information ● Engine exhaust, some of its constituents, and a wide variety of automobile components contain or emit chemicals known to the State of California to cause cancer and birth defects and other reproductive harm.
Page 407: General Maintenance
“Owner’s Warranty Information Booklet” or “Owner’s Manual Supplement/Sched- uled Maintenance Guide”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice. Engine compartment...
Page 408 6-2. Maintenance Vehicle interior Items Check points • The accelerator pedal should Accelerator pedal move smoothly (without uneven pedal effort or catching). • When parked on a slope and the Hybrid transmission “Park” mecha- shift lever is in P, is the vehicle nism securely stopped? •...
Page 409 6-2. Maintenance Items Check points • Do seat belts operate smoothly? Seat belts • The seat belts should not be dam- aged. • Do the seat controls operate prop- Seats erly? • Does the steering wheel rotate smoothly? • Does the steering wheel have the Steering wheel correct amount of free play? •...
Page 410 6-2. Maintenance WARNING ■ If the hybrid system is operating Turn the hybrid system off and ensure that there is adequate ventilation before performing maintenance checks.
Page 411: Maintenance (I/M Programs
The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/M test and may need to be repaired. Contact your Toyota dealer to service the vehicle. Your vehicle may not pass the I/M test in the following situations: ●...
Page 412: Do-It-Yourself Service Precautions
• Rag or paper towel (→P. 422) • Funnel (used only for adding brake fluid) • “Toyota Super Long Life Coolant” or a similar high quality ethylene glycol-based non-silicate, non- amine, non-nitrite and non-borate coolant with long- life hybrid organic acid technology Engine/power U.S.A.:...
Page 413 6-3. Do-it-yourself maintenance Items Parts and tools Tire inflation • Tire pressure gauge pressure • Compressed air source (→P. 443) • Water or washer fluid containing antifreeze (for win- Washer fluid ter use) (→P. 423) • Funnel (used only for adding water or washer fluid) WARNING The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized.
Page 414: Hood
6-3. Do-it-yourself maintenance Hood Release the lock from the inside of the vehicle to open the hood. Pull the hood lock release lever. The hood will pop up slightly. Pull up the auxiliary catch lever and lift the hood. ■ Open hood warning buzzer If the vehicle reaches a speed of 3 mph (5 km/h), the master warning light flashes and a buzzer sounds to indicate that the hood is not fully closed.
Page 415: Positioning A Floor Jack
6-3. Do-it-yourself maintenance Positioning a floor jack When using a floor jack, follow the instructions in the manual provided with the jack and perform the operation safely. When raising your vehicle with a floor jack, position the jack cor- rectly. Improper placement may damage your vehicle or cause injury.
Page 416: Engine Compartment
6-3. Do-it-yourself maintenance Engine compartment Fuse boxes (→P. 457) Electric cooling fan Engine oil filler cap (→P. 418) Condenser (→P. 421) Engine oil level dipstick Power control unit (→P. 417) coolant reservoir (→P. 420) Brake fluid reservoir Engine coolant reservoir (→P.
Page 417 6-3. Do-it-yourself maintenance Engine oil With the engine at operating temperature and turned off, check the oil level on the dipstick. ■ Checking the engine oil Park the vehicle on level ground. After warming up the engine and turning it off the hybrid system, wait more than 5 minutes for the oil to drain back into the bottom of the engine.
Page 418 6-3. Do-it-yourself maintenance ■ Adding engine oil If the oil level is below or near the low level mark, add engine oil of the same type as that already in the engine. Make sure to check the oil type and prepare the items needed before adding oil.
Page 419 Dispose of used oil and filters only in a safe and acceptable manner. Do not dispose of used oil and filters in household trash, in sewers or onto the ground. Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal. ●...
Page 420 U.S.A.: “Toyota Super Long Life Coolant” is a mixture of 50% coolant and 50% deion- ized water. (Minimum temperature: -31°F [-35°C]) Canada: “Toyota Super Long Life Coolant” is a mixture of 55% coolant and 45% deion- ized water.
Page 421 If the coolant level drops within a short time of replenishing Visually check the radiators, hoses, engine/power control unit coolant reser- voir caps, drain cock and water pump. If you cannot find a leak, have your Toyota dealer test the cap and check for leaks in the cooling system. WARNING ■...
Page 422 6-3. Do-it-yourself maintenance Brake fluid ■ Checking fluid level The brake fluid level should be between the “MAX” and “MIN” lines on the tank. “MAX” “MIN” ■ Adding fluid Make sure to check the fluid type and prepare the necessary item. Fluid type FMVSS No.116 DOT 3 or SAE J1703 brake fluid Item...
Page 423 6-3. Do-it-yourself maintenance Washer fluid Add washer fluid in the following situations: ● A washer does not work. ● “Windshield Washer Fluid Low” is displayed on the multi-infor- mation display. WARNING ■ When adding washer fluid Do not add washer fluid when the hybrid system is hot or operating as washer fluid contains alcohol and may catch fire if spilled on the engine, etc.
Page 424: Volt Battery
6-3. Do-it-yourself maintenance 12-volt battery Location The 12-volt battery is located on the right-hand side of the trunk. Removing the 12-volt battery cover Remove the 12-volt battery cover.
Page 425 12-volt battery was disconnected. Make sure to turn off the power before disconnecting the 12-volt battery. Take extra care when connecting the 12-volt battery if the power switch mode prior to discharge is unknown. If the system will not start even after multiple attempts, contact your Toyota dealer.
Page 426 When replacing the 12-volt battery Use a 12-volt battery designed for this vehicle. Failure to do so may cause gas (hydrogen) to enter the passenger compartment, causing a fire or explosion. For replacement of the 12-volt battery, contact your Toyota dealer.
Page 427 6-3. Do-it-yourself maintenance NOTICE ■ When recharging the 12-volt battery Never recharge the 12-volt battery while the hybrid system is operating. Also, be sure all accessories are turned off.
Page 428: Tires
Tire rotation Rotate the tires in the order shown. To equalize tire wear and extend tire life, Toyota recommends that tire rotation is carried out at the same interval as tire inspection. Front Do not fail to initialize the tire pressure warning system after tire rotation.
Page 429 6-3. Do-it-yourself maintenance Tire pressure warning system Your vehicle is equipped with a tire pressure warning system that uses tire pressure warning valve and transmitters to detect low tire inflation pressure before serious problems arise.  Vehicles without a tire inflation pressure display function If the tire pressure drops below a predetermined level, the driver is warned by a screen display and a warning light.
Page 430 6-3. Do-it-yourself maintenance ◆ Installing tire pressure warning valves and transmitters When replacing the tires or wheels, the tire pressure warning valve and transmitters must be installed to the wheels which will be installed to the vehicle. When new tire pressure warning valve and transmitters are installed, new ID codes must be registered in the tire pressure warning computer and the tire pressure warning system must be initialized.
Page 431 6-3. Do-it-yourself maintenance Select “Set Pressure” then press and hold until the tire pressure warning light blinks 3 times. Then a message will be dis- played on the multi-information display. Vehicles with a tire inflation pressure display function: “- -” will be displayed on the multi- information display for the inflation pressure of each tire...
Page 432 ID codes initially registered to the vehicle, a second set of ID codes can be registered. A second set of tire pressure warning system sensor ID codes can be registered at your Toyota dealer. When 2 sets of ID codes have been registered, either ID code set can be selected. ...
Page 433 6-3. Do-it-yourself maintenance Select “Change Wheel” then press and hold until the tire pressure warning light blinks slowly 3 times. Then a message will be dis- played on the multi-information display. When registration is being per- formed, the tire pressure warn- light will blink...
Page 434 ● A tire goes flat repeatedly or cannot be properly repaired due to the size or location of a cut or other damage If you are not sure, consult with your Toyota dealer. ■ Replacing tires and wheels If the ID codes of the tire pressure warning valve and transmitters are not registered, the tire pressure warning system will not work properly.
Page 435 6-3. Do-it-yourself maintenance ■ Tire types ● Summer tires Summer tires are high-speed performance tires best suited to highway driving under dry conditions. Since summer tires do not have the same traction performance as snow tires, summer tires are inadequate for driving on snow-covered or icy roads.
Page 436 ● In the following situations, the tire pressure warning system may not operate properly. • If non-genuine Toyota wheels are used. • If a tire has been replaced with a tire that is not an OE (Original Equipment) tire. • If a tire has been replaced with a tire that is not of the specified size.
Page 437 If repeated attempts to record tire inflation pressure settings are unsuccessful, have the vehicle inspected by your Toyota dealer. ● If initialization is attempted and the tire pressure warning light does not blink 3 times.
Page 438 1 minute and then illuminates. ● If initialization cannot be completed after performing the above proce- dure, contact your Toyota dealer. ■ When registering ID codes (vehicles with a tire inflation pressure dis- play function) ●...
Page 439 6-3. Do-it-yourself maintenance ■ Canceling ID code registration (vehicles with a tire inflation pressure display function) ● To cancel ID code registration after it has been started, turn the power switch off before driving the vehicle. If the vehicle is driven after ID code registration is started, to cancel reg- istration, perform the ID code registration start procedure again and turn the power switch off before driving.
Page 440 ID code registration, the tire pressure warning light blinks for approximately 1 minute and then illuminates. ● If ID code registration cannot be completed after performing the above procedure, contact your Toyota dealer. ■ Tire pressure warning system certification ...
Page 441 Do not mix tires of different makes, models or tread patterns. Also, do not mix tires of remarkably different treadwear. ● Do not use tire sizes other than those recommended by Toyota. ● Do not mix differently constructed tires (radial, bias-belted or bias-ply tires).
Page 442 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and transmitter when replacing the tire.
Page 443: Tire Inflation Pressure
6-3. Do-it-yourself maintenance Tire inflation pressure Tire inflation pressure The recommended cold tire infla- tion pressure and tire size are dis- played on the tire and loading information label. (→P. 532)
Page 444 Driving with incorrect tire inflation pressure may result in the following: ● Reduced fuel economy ● Reduced driving comfort and poor handling ● Reduced tire life due to wear ● Reduced safety ● Damage to the drivetrain If a tire needs frequent inflating, have it checked by your Toyota dealer.
Page 445 6-3. Do-it-yourself maintenance ■ Instructions for checking tire inflation pressure When checking tire inflation pressure, observe the following: ● Check only when the tires are cold. If your vehicle has been parked for at least 3 hours or has not been driven for more than 1 mile or 1.5 km, you will get an accurate cold tire inflation pressure reading.
Page 446: Wheels
● Used wheels ● Bent wheels that have been straightened Aluminum wheel precautions (if equipped) ● Use only Toyota wheel nuts and wrenches designed for use with your aluminum wheels. ● When rotating, repairing or changing your tires, check that the wheel nuts are still tight after driving 1000 miles (1600 km).
Page 447 Because tire repair or replacement may affect the tire pressure warn- ing valve and transmitters, make sure to have tires serviced by your Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valve and transmitters at your Toyota dealer.
Page 448: Air Conditioning Filter
6-3. Do-it-yourself maintenance Air conditioning filter The air conditioning filter must be changed regularly to maintain air conditioning efficiency. Removal method Turn the power switch off. Open glove remove the glove box cover inside the glove box. Remove the filter cover. Unlock the filter cover.
Page 449 6-3. Do-it-yourself maintenance Remove the air conditioning fil- ter from the filter case and replace it with a new one. The “↑UP” marks shown on the fil- ter and the filter case should be pointing up. ■ Checking interval Inspect and replace the air conditioning filter according to the maintenance schedule.
Page 450: Traction Battery Air Intake Vent
6-3. Do-it-yourself maintenance Hybrid battery (traction battery) air intake vent To prevent an increase in fuel consumption, visually inspect the hybrid battery (traction battery) air intake vent periodically for dust and clogs. If it is dusty or clogged or if “Maintenance Required for Traction Battery Cooling Parts See Owner’s Man- ual”...
Page 451 6-3. Do-it-yourself maintenance Remove the air intake vent cover. Pull the cover as shown in the illustration to disengage the 7 claws, starting from the claw in the upper right cor- ner. Pull the cover toward the front of the vehicle to remove Remove the air intake vent fil- ter.
Page 452 6-3. Do-it-yourself maintenance Reinstall the filter to the cover. Engage the filter to the 2 claws as shown in the illus- tration. Engage the 3 claws to install the filter. Make sure that the filter is not crooked or deformed when install- ing it.
Page 453 It may take approximately 20 minutes after the hybrid system is started until the warning message disappears. If the warning message does not disap- pear, have the vehicle inspected by your Toyota dealer. WARNING ■...
Page 454 ● Carefully handle the removed filter so that it will not be damaged. If the filter is damaged, have it replaced with a new filter by your Toyota dealer. ● Make sure to reinstall the filter and cover to their original positions after cleaning.
Page 455: Electronic Key Battery
6-3. Do-it-yourself maintenance Electronic key battery Replace the battery with a new one if it is depleted. You will need the following items: ● Flathead screwdriver ● Small flathead screwdriver ● Lithium battery CR2032 Replacing the battery Release the lock and remove the mechanical key.
Page 456 Be careful not to lose the battery or any other small parts. ■ Use a CR2032 lithium battery ● Batteries can be purchased at your Toyota dealer, local electrical appliance shops or camera stores. ● Replace only with the same or equivalent type recommended by the manu- facturer.
Page 457: Checking And Replacing Fuses
6-3. Do-it-yourself maintenance Checking and replacing fuses If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as nec- essary. Turn the power switch off. Open the fuse box cover. ...
Page 458 6-3. Do-it-yourself maintenance Remove the fuse with the pull- out tool. Only type A fuses can be removed using the pullout tool. Check if the fuse is blown.  Type A  Type B Type C  Normal fuse Blown fuse Replace the blown fuse with a new fuse of an appropriate amperage rat- ing.
Page 459 If the lights do not turn on even after the fuse has been replaced, a bulb may need replacement. (→P. 460) ● If the replaced fuse blows again, have the vehicle inspected by your Toyota dealer. ■ If there is an overload in a circuit The fuses are designed to blow, protecting the wiring harness from damage.
Page 460: Light Bulbs
Light bulbs You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer.
Page 461 6-3. Do-it-yourself maintenance Replacing light bulbs ■ Front turn signal/parking lights (bulb type) Turn the bulb base counter- clockwise. Remove the light bulb. Install a new light bulb and then install the bulb base to the light unit by inserting it and turning it clockwise.
Page 462 6-3. Do-it-yourself maintenance ■ Front side marker lights (bulb type) To ensure enough space to perform work, turn the steer- ing wheel to move the front wheel away from the light bulb to be replaced. Turn the steering wheel to the left when replacing the right side light bulb, and turn the steering wheel to the right when replac-...
Page 463 6-3. Do-it-yourself maintenance Insert a small flathead screw- driver between front bumper and fender liner at the position marked with a “∇” and then separate the front bumper from the fender liner. To separate the front bumper from the fender liner, pry up the fender liner while pulling the front bumper outward as shown in the illustration.
Page 464 6-3. Do-it-yourself maintenance Return the fender liner to its original position, and install the clips. Make sure that the fender liner is correctly positioned on the inner side of the front bumper. To Install the fender liner to the front bumper, engage the clip to the front bumper.
Page 465 6-3. Do-it-yourself maintenance ■ Back-up lights (bulb type) Open trunk remove the clips. To prevent damaging the vehi- cle, wrap the tip of the flathead screwdriver with tape. Partly remove the trunk lid cover. Disconnect connector while depressing the lock release.
Page 466 6-3. Do-it-yourself maintenance Remove the light bulb. Install a new light bulb and then install the bulb base to the light unit by inserting it and turning it clockwise. Connect connector. (When replacing right side bulb only.) Reinstall the trunk lid cover with the clips.
Page 467 6-3. Do-it-yourself maintenance ■ Rear turn signal lights (bulb type) and rear side marker lights (bulb type) Open the trunk and apply protective tape to the vehicle body around the light unit. Use masking tape, etc. Do not use duct tape, as it may leave residue or damage the paint when removed.
Page 468 6-3. Do-it-yourself maintenance Remove the light unit. Attach a long piece of packing tape to the light unit and fold the excess in half. Hold the folded portion and pull it toward the rear of the vehicle to remove the light unit. Turn the bulb base counterclockwise.
Page 469 6-3. Do-it-yourself maintenance Install a new light bulb and then install the bulb base to the light unit by inserting it and turning it clockwise.  Rear turn signal lights  Rear side marker lights Install the light unit. Align the tabs and push the light unit toward the front of the vehi- cle to install it.
Page 470 (bulb type), back-up lights (bulb type), rear turn signal lights (bulb type) and rear side marker lights (bulb type) consist of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced.
Page 471 6-3. Do-it-yourself maintenance WARNING ■ Replacing light bulbs ● Turn off the lights. Do not attempt to replace the bulb immediately after turning off the lights. The bulbs become very hot and may cause burns. ● Do not touch the glass portion of the light bulb with bare hands. When it is unavoidable to hold the glass portion, use and hold with a clean dry cloth to avoid getting moisture and oils on the bulb.
Page 472 6-3. Do-it-yourself maintenance...
Page 473 When trouble arises 7-1. Essential information Emergency flashers ..474 If your vehicle has to be stopped in an emergency ...... 475 7-2. Steps to take in an emergency If your vehicle needs to be towed ......476 If you think something is wrong ......
Page 474: Emergency Flashers
7-1. Essential information Emergency flashers The emergency flashers are used to warn other drivers when the vehicle has to be stopped on the road due to a breakdown, etc. Press the switch. All the turn signal lights will flash. To turn them off, press the switch once again.
Page 475: Stopped In An Emergency
7-1. Essential information If your vehicle has to be stopped in an emergency Only in an emergency, such as if it becomes impossible to stop the vehicle in the normal way, stop the vehicle using the follow- ing procedure: Steadily step on the brake pedal with both feet and firmly depress it. Do not pump the brake pedal repeatedly as this will increase the effort required to slow the vehicle.
Page 476: If Your Vehicle Needs To Be Towed
If your vehicle needs to be towed If towing is necessary, we recommend having your vehicle towed by your Toyota dealer or a commercial towing service, using a wheel-lift type truck or flatbed truck. Use a safety chain system for all towing, and abide by all state/ provincial and local laws.
Page 477 7-2. Steps to take in an emergency Using a flatbed truck If your vehicle is transported by a flatbed truck, it should be tied down at the locations shown in the illustration. Covers are installed to the tie-down holes. After transporting vehicle, make sure to reinstall the covers to...
Page 478 7-2. Steps to take in an emergency WARNING Observe the following precautions. Failure to do so may result in death or serious injury. ■ When towing the vehicle Be sure to transport the vehicle with the front wheels raised or with all four wheels raised off the ground.
Page 479: If You Think Something Is Wrong
7-2. Steps to take in an emergency If you think something is wrong If you notice any of the following symptoms, your vehicle proba- bly needs adjustment or repair. Contact your Toyota dealer as soon as possible. Visible symptoms ● Fluid leaks under the vehicle.
Page 480: On Or A Warning Buzzer Sounds
• The brake fluid level is low; or (U.S.A.) • The brake system is malfunctioning → Immediately stop the vehicle in a safe place and con- tact your Toyota dealer. Continuing to drive the vehi- (Red) cle may be dangerous. (Canada)
Page 481 Indicates a malfunction in: • The ABS; or (U.S.A.) • The brake assist system → Have the vehicle inspected by your Toyota dealer immediately. (Canada) Parking brake indicator (warning buzzer) It is possible that the parking brake is not fully engaged or...
Page 482 Warning light/Details/Actions PCS warning light When the warning light flashes: Indicates a malfunction in the PCS (Pre-Collision System) → Have the vehicle inspected by your Toyota dealer immediately. When the warning light illuminates: Indicates that the PCS (Pre-Collision System) is temporar- ily unavailable, possibly due to either of the following: •...
Page 483 7-2. Steps to take in an emergency Warning light Warning light/Details/Actions Low fuel level warning light Indicates that remaining fuel is approximately 1.8 gal. (6.7 L, 1.5 Imp. gal.) or less → Refuel the vehicle. Driver’s and front passenger’s seat belt reminder light (warning buzzer) Warns the driver and/or front passenger to fasten their seat belts...
Page 484 7-2. Steps to take in an emergency : Parking brake engaged warning buzzer: A buzzer will sound if the vehicle is driven at a speed of approximately 3 mph (5 km/h) or more. : Driver’s seat belt buzzer: The driver’s seat belt buzzer sounds to alert the driver that his or her seat belt is not fastened.
Page 485 Is the fuel tank cap loose? If it is, tighten it securely. The light will go off after several driving trips. If the light does not go off even after several trips, contact your Toyota dealer as soon as possible.
Page 486 (→P. 430) If the warning light does not turn off several minutes after the initialization has been performed, have the vehicle inspected by your Toyota dealer immediately. ...
Page 487 ■ If both the ABS and the brake system warning lights remain on Stop your vehicle in a safe place immediately and contact your Toyota dealer. The vehicle will become extremely unstable during braking, and the ABS system may fail, which could cause an accident resulting in death or serious injury.
Page 488 7-2. Steps to take in an emergency WARNING ■ Maintenance of the tires Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label (tire and load information label).
Page 489 7-2. Steps to take in an emergency NOTICE ■ To ensure the tire pressure warning system operates properly Do not install tires with different specifications or makers, as the tire pressure warning system may not operate properly.
Page 490: If A Warning Message Is Displayed
Multi-information display Handling method Follow the instructions of the message on the multi-information display. If any of the warning messages are shown again after the appropriate actions have been performed, contact your Toyota dealer.
Page 491 Messages and warnings The warning lights and warning buzzers operate as follows depending on the content of the message. If a message indicates the need for inspection by a dealer, have the vehicle inspected by your Toyota dealer immediately. System...
Page 492 ● If the following messages are shown, there may be a malfunction. Immediately stop the vehicle in a safe place and contact your Toyota dealer. Continuing to drive the vehicle may be dangerous. • “Low Braking Power Stop in a Safe Place See Owner’s Manual”...
Page 493 7-2. Steps to take in an emergency ■ If “Hybrid System Overheated Reduced Output Power” is shown This message may be displayed when driving under severe operating condi- tions. (For example, when driving up a long steep hill.) Handling method: →P. 519 ■...
Page 494 If this message is displayed but you have not had a new electronic key regis- tered, ask your Toyota dealer to check if an unknown electronic key (other than those in your possession) has been registered.
Page 495 It “High Power Consumption Power to Climate Temporarily Limited” is frequently shown There is a possible malfunction relating to the charging system or the 12- volt battery may be deteriorating. Have the vehicle inspected by your Toyota dealer. ■ If “Have Traction Battery Inspected” is shown (AXVH70 model The hybrid battery (traction battery) is scheduled to be inspected or replaced.
Page 496 7-2. Steps to take in an emergency If you have a flat tire Your vehicle is equipped with a spare tire. The flat tire can be replaced with the spare tire. For details about tires: →P. 428 WARNING ■ If you have a flat tire Do not continue driving with a flat tire.
Page 497 7-2. Steps to take in an emergency WARNING ■ Using the tire jack Observe the following precautions. Improper use of the tire jack may cause the vehicle to suddenly fall off the jack, leading to death or serious injury. ● Do not use the tire jack for any purpose other than replacing tires or installing and removing tire chains.
Page 498 7-2. Steps to take in an emergency Taking out the jack Lift up the hook of the luggage floor cover on the trunk floor. Secure the luggage floor cover using the hook provided. Remove the jack. Taking out the spare tire Lift up the hook of the luggage floor cover on the trunk floor.
Page 499 7-2. Steps to take in an emergency Secure the luggage floor cover using the hook provided. Remove the tool tray. Loosen the center fastener that secures the spare tire. When taking out or stowing the spare tire, make sure to firmly hold opposite end of the tire.
Page 500 7-2. Steps to take in an emergency Replacing a flat tire Chock the tires. Flat tire Wheel chock positions Left-hand side Behind the rear right-hand side tire Front Right-hand side Behind the rear left-hand side tire Left-hand side In front of the front right-hand side tire Rear Right-hand side In front of the front left-hand side tire...
Page 501 7-2. Steps to take in an emergency Turn the tire jack portion “A” by hand until the notch of the jack is in contact with the jack point. To prevent damage to the vehicle when using the jack, position the jack in the correct location.
Page 502 • If there are any cracks or deformations in the bolt screws, nut threads or bolt holes of the wheel, have the vehicle inspected by your Toyota dealer. • When installing the wheel nuts, be sure to install them with the...
Page 503 7-2. Steps to take in an emergency Installing the spare tire Remove any dirt or foreign mat- ter from the wheel contact sur- face. If foreign matter is on the wheel contact surface, the wheel nuts may loosen while the vehicle is in motion, causing the tire to come off.
Page 504 7-2. Steps to take in an emergency Firmly tighten each wheel nut two or three times in the order shown in the illustration. Tightening torque: 76 ft•lbf (103 N•m, 10.5 kgf•m) Stow the flat tire, tire jack and all tools. ■...
Page 505 • AFS (Adaptive Front-lighting (ICS) System) • Rear view monitor system • Dynamic radar cruise control • Toyota parking assist monitor with full-speed range • Panoramic view monitor • LDA (Lane Departure Alert with • Navigation system steering control) If equipped ■...
Page 506 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and...
Page 507: If The Hybrid System Will Not Start
7-2. Steps to take in an emergency If the hybrid system will not start Reasons for the hybrid system not starting vary depending on the situation. Check the following and perform the appropriate procedure: The hybrid system will not start even though the correct starting procedure is being followed.
Page 508 ● The 12-volt battery may be discharged. (→P. 512) ● One or both of the 12-volt battery terminals may be disconnected. (→P. 424) Contact your Toyota dealer if the problem cannot be repaired, or if repair procedures are unknown. Emergency start function...
Page 509: If The Electronic Key Does Not Operate Properly
Turning the key rearward unlocks the driver's door. Turning the key once again unlocks the other doors. Opens the windows and the moon roof (turn and hold) : If equipped : This setting must be customized at your Toyota dealer.
Page 510 Turn the mechanical key clock- wise to open. Starting the hybrid system Ensure that the shift lever is in P and firmly depress the brake pedal. Touch the Toyota emblem side of the electronic key to the power switch. When electronic detected, a buzzer sounds and the power switch will turn to ON mode.
Page 511 7-2. Steps to take in an emergency ■ Stopping the hybrid system Shift the shift lever to P and press the power switch as you normally do when stopping the hybrid system. ■ Replacing the key battery As the above procedure is a temporary measure, it is recommended that the electronic key battery be replaced immediately when the battery is depleted.
Page 512: If The 12-Volt Battery Is Discharged
The following procedures may be used to start the hybrid sys- tem if the vehicle’s 12-volt battery is discharged. You can also call your Toyota dealer or a qualified repair shop. If you have a set of jumper (or booster) cables and a second vehicle with a 12-volt battery, you can jump start your vehicle by following the steps below.
Page 513 7-2. Steps to take in an emergency Connect the jumper cables according to the following procedure: Connect a positive jumper cable clamp to the exclusive jump starting terminal on your vehicle. Connect the clamp on the other end of the positive cable to the positive (+) battery terminal on the second vehicle.
Page 514 ON mode, then start the vehicle's engine. Make sure the “READY” indicator comes on. If the indicator does not come on, contact your Toyota dealer. Once the hybrid system has started, remove the jumper cables in the exact reverse order from which they were connected.
Page 515 ■ When the 12-volt battery is removed or discharged ● Information stored in the ECU is cleared. When the 12-volt battery is depleted, have the vehicle inspected at your Toyota dealer. ● Some systems may require initialization. (→P. 559) ■...
Page 516 (Depending on the 12-volt battery to be replaced, the exhaust hole may be plugged.) Exhaust hole plug Exhaust hole Exhaust hose Hole section of the vehicle For details, consult your Toyota dealer.
Page 517 Do not allow children near the 12-volt battery. ■ After recharging the 12-volt battery Have the 12-volt battery inspected at your Toyota dealer as soon as possi- ble. If the 12-volt battery is deteriorating, continued use may cause the 12-volt battery to emit a malodorous gas, which may be detrimental to the health of passengers.
Page 518 7-2. Steps to take in an emergency WARNING ■ When replacing the 12-volt battery After replacing, securely attach the exhaust hose and exhaust hole plug to the exhaust hole of the replaced 12-volt battery. If not properly installed, gases (hydrogen) may leak into the vehicle interior, and there is the possi- ble danger of the gas igniting and exploding.
Page 519: If Your Vehicle Overheats
If you do not see steam: Carefully lift the hood. After the hybrid system has cooled down sufficiently, inspect the hoses and radiator core (radiator) for any leaks. Radiator Cooling fan If a large amount of coolant leaks, immediately contact your Toyota dealer.
Page 520 (The fan may not operate in freezing tem- peratures.) If the fan is not operating: Stop the hybrid system immediately and contact your Toyota dealer. If the fan is operating: Have the vehicle inspected at the nearest Toyota dealer.
Page 521 (radiator) for any leaks. Radiator Cooling fan If a large amount of coolant leaks, immediately contact your Toyota dealer. The coolant level is satisfac- tory if it is between the “FULL” and “LOW” lines on the reservoir. Reservoir “FULL”...
Page 522 Stop the hybrid system and contact your Toyota dealer. If the message is not displayed: The hybrid system temperature has dropped and the vehicle may be driven normally. However, if the message appears again frequently, contact your Toyota dealer. WARNING ■...
Page 523: If The Vehicle Becomes Stuck
7-2. Steps to take in an emergency If the vehicle becomes stuck Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt or snow: Stop the hybrid system. Set the parking brake and shift the shift lever to P.
Page 524 7-2. Steps to take in an emergency NOTICE ■ To avoid damaging the transmission and other components ● Avoid spinning the front wheels and depressing the accelerator pedal more than necessary. ● If the vehicle remains stuck even after these procedures are performed, the vehicle may require towing to be freed.
Page 525 Vehicle specifications 8-1. Specifications Maintenance data (fuel, oil level, etc.) ..526 Fuel information ....535 Tire information ....538 8-2. Customization Customizable features ..551 8-3. Items to initialize Items to initialize ....559...
Page 526 8-1.Specifications Maintenance data (fuel, oil level, etc.) Dimensions and weights 192.1 in. (4880 mm) Overall length 192.7 in. (4895 mm) Overall width 72.4 in. (1840 mm) Overall height 56.9 in. (1445 mm) Wheelbase 111.2 in. (2825 mm) 63.0 in. (1600 mm) Front 62.6 in.
Page 527 The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle. This number is stamped on the top left of the instrument panel.
Page 528 8-1. Specifications Engine Model A25A-FXS Type 4-cylinder in line, 4-cycle, gasoline 3.44 × 4.07 in. (87.5 × 103.4 mm) Bore and stroke Displacement 151.8 cu. in. (2487 cm Valve clearance Automatic adjustment Fuel Fuel type Unleaded gasoline only Octane rating 87 (Research Octane Number 91) or higher Fuel tank capacity 13 gal.
Page 529 5 minutes, and check the oil level on the dipstick. ■ Engine oil selection “Toyota Genuine Motor Oil” is used in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to sat- isfy the following grade and viscosity.
Page 530 (Reference)  Power control unit 1.9 qt. (1.8 L, 1.6 Imp. qt.) Use either of the following: • “Toyota Super Long Life Coolant” • Similar high-quality ethylene glycol-based Coolant type non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology Do not use plain water alone.
Page 531 : The fluid capacity is a reference quantity. If replacement is necessary, contact your Toyota dealer. NOTICE ■ Transmission fluid type Using transmission fluid other than “Toyota Genuine ATF WS” may ulti- mately damage the transmission of your vehicle. Brakes Pedal clearance 3.3 in. (85 mm) 0.04 ⎯...
Page 532 8-1. Specifications Tires and wheels Type A  Tire size 205/65R16 95H, T155/70D17 110M Driving under normal conditions Front: 35 psi (240 kPa, 2.4 kgf/cm or bar) Rear: 35 psi (240 kPa, 2.4 kgf/cm or bar) Spare: Tire inflation pressure 60 psi (420 kPa, 4.2 kgf/cm or bar) (Recommended cold tire...
Page 533 8-1. Specifications Type C  Tire size 235/45R18 94V, T155/70D17 110M Driving under normal conditions Front: 35 psi (240 kPa, 2.4 kgf/cm or bar) Rear: 35 psi (240 kPa, 2.4 kgf/cm or bar) Spare: Tire inflation pressure 60 psi (420 kPa, 4.2 kgf/cm or bar) (Recommended cold tire Driving at high speeds (above 100 mph...
Page 534 8-1. Specifications Light bulbs Light bulbs Bulb No. Type Front side marker lights (bulb type) Front turn signal/ parking lights 7444NA 28/8 (bulb type) Exterior Rear turn signal lights WY21W (bulb type) Rear side marker lights (bulb type) Back-up lights (bulb type) ⎯...
Page 535: Fuel Information
In very few cases, driveability problems may be caused by the brand of gaso- line you are using. If driveability problems persist, try changing the brand of gasoline. If this does not correct the problem, consult your Toyota dealer. ■...
Page 536 Non-recommendation of the use of gasoline containing MMT Some gasoline contains an octane enhancing additive called MMT (Methylcy- clopentadienyl Manganese Tricarbonyl). Toyota does not recommend the use of gasoline that contains MMT. If fuel containing MMT is used, your emission control system may be adversely affected.
Page 537 8-1. Specifications NOTICE ■ Notice on fuel quality ● Do not use improper fuels. If improper fuels are used, the engine will be damaged. ● Do not use leaded gasoline. Leaded gasoline can cause damage to your vehicle’s three-way catalytic converters causing the emission control system to malfunction.
Page 538: Tire Information
8-1. Specifications Tire information Typical tire symbols  Full-size tire Compact spare tire ...
Page 539 8-1. Specifications Tire size (→P. 541) Summer tires or all season tires (→P. 435) An all season tire has “M+S” on the sidewall. A tire not marked “M+S” is a summer tire. TUBELESS or TUBE TYPE A tubeless tire does not have a tube and air is directly put into the tire. A tube type tire has a tube inside the tire and the tube maintains the air pressure.
Page 540 8-1. Specifications Typical DOT and Tire Identification Number (TIN) Type A Type B   DOT symbol Tire Identification Number (TIN) Tire manufacturer’s identification mark Tire size code Manufacturer’s optional tire type code (3 or 4 letters) Manufacturing week Manufacturing year Manufacturer’s code : The DOT symbol certifies that the tire conforms to applicable Federal Motor Vehicle Safety Standards.
Page 541 8-1. Specifications Tire size ■ Typical tire size information The illustration indicates typical tire size. Tire use (P = Passenger car [some- times omitted], T = Temporary use) Section width (millimeters) Aspect ratio (tire height to section width) Tire construction code (R = Radial, D = Diagonal) Wheel diameter (inches) Load index (2 digits or 3 digits) Speed symbol (alphabet with one letter)
Page 542 8-1. Specifications Tire section names Bead Sidewall Shoulder Tread Belt Inner liner Reinforcing rubber Carcass Rim lines Bead wires Chafer...
Page 543 U.S. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading. Your Toyota dealer will help answer any questions you may have as you read this information. ■ DOT quality grades All passenger vehicle tires must conform to Federal Safety Require- ments in addition to these grades.
Page 544 8-1. Specifications ■ Temperature A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissi- pate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 545 8-1. Specifications Glossary of tire terminology Tire related term Meaning Tire pressure when the vehicle has been Cold tire inflation pres- parked for three hours or more, or has not sure been driven more than 1 mile or 1.5 km under that condition The maximum cold inflated pressure to which Maximum...
Page 546 8-1. Specifications Tire related term Meaning The combined weight of installed regular pro- duction options weighing over 5 lb. (2.3 kg) in excess of the standard items which they Production options replace, not previously considered in curb weight weight or accessory weight, including heavy duty brakes, ride levelers, roof rack, heavy duty battery, and special trim A metal support for a tire or a tire and tube...
Page 547 8-1. Specifications Tire related term Meaning A pneumatic tire in which the ply cords that extend to the beads are laid at alternate Bias ply tire angles substantially less than 90 degrees to the centerline of the tread The tire structure, except tread and sidewall Carcass rubber which, when inflated, bears the load The breaking away of pieces of the tread or...
Page 548 8-1. Specifications Tire related term Meaning A tire designated by its manufacturer as pri- Light truck (LT) tire marily intended for use on lightweight trucks or multipurpose passenger vehicles The maximum load that a tire is rated to carry Load rating for a given inflation pressure The load rating for a tire at the maximum per- Maximum load rating...
Page 549 8-1. Specifications Tire related term Meaning The linear distance between the exteriors of the sidewalls of an inflated tire, excluding ele- Section width vations due to labeling, decoration, or protec- tive bands That portion of a tire between the tread and Sidewall bead The parting of the rubber compound from the...
Page 550 8-1. Specifications Designated seating Occupant distribution Vehicle normal load, capacity, Number of in a normally loaded Number of occupants occupants vehicle 2 through 4 2 in front 2 in front, 1 in second 5 through 10 seat 2 in front, 1 in second 11 through 15 seat, 1 in third seat, 1 in fourth seat...
Page 551 The settings of these fea- tures can be changed using the multi-information display, on the audio system screen, or at your Toyota dealer. Customizing vehicle features When customizing vehicle features, ensure that the vehicle is parked in a safe place with the shift lever in P and the parking brake set.
Page 552: Customization Customizable Features
Customizable features Some function settings are changed simultaneously with other func- tions being customized. Contact your Toyota dealer for further details. Settings that can be changed on the audio system screen Settings that can be changed by your Toyota dealer Definition of symbols: O = Available, —...
Page 553 8-2. Customization ■ Door lock (→P. 150, 156, 509) Function Default setting Customized setting Driver’s door unlocked in one Unlocking using All doors unlocked in step, all doors — O mechanical key one step. unlocked in two steps Shift position Automatic door lock linked door lock- Speed linked door...
Page 554 8-2. Customization ■ Smart key system and wireless remote control (→P. 150, 156, 160) Function Default setting Customized setting Operation buzzer vol- Off to 7 Operation signal (Emergency flashers) Time elapsed before automatic door lock 30 seconds function is activated if 60 seconds door is not opened after 120 seconds...
Page 555 8-2. Customization ■ Wireless remote control (→P. 146, 150, 156) Function Default setting Customized setting Wireless remote control — O Driver’s door unlocked in one All doors unlocked in Unlocking operation step, all doors one step unlocked in two steps One short press Push twice Trunk unlocking opera-...
Page 556 8-2. Customization ■ Automatic light control system (→P. 227) Function Default setting Customized setting Light sensor sensitivity Standard -2 to 2 Time elapsed before headlights automatically 30 seconds 60 seconds turn off after doors are closed 90 seconds ■ Lights (→P. 227) Function Default setting Customized setting...
Page 557 8-2. Customization ■ Automatic air conditioning system (→P. 344) Function Default setting Customized setting A/C auto switch opera- Auto Manual tion ■ Illumination (→P. 354) Function Default setting Customized setting Time elapsed before 15 seconds 7.5 seconds lights turn off 30 seconds Operation after...
Page 558 8-2. Customization WARNING ■ During customization As the hybrid system needs to be operating during customization, ensure that the vehicle is parked in a place with adequate ventilation. In a closed area such as a garage, exhaust gases including harmful carbon monoxide (CO) may collect and enter the vehicle.
Page 559 8-3. Items to initialize Items to initialize The following items must be initialized for normal system opera- tion after such cases as the 12-volt battery being reconnected, or maintenance being performed on the vehicle: Item When to initialize Reference Message indicating mainte- •...
Page 560 8-3. Items to initialize...
Page 561: For Owners
For owners Reporting safety defects for U.S. owners......562 Seat belt instructions for Canadian owners (in French) ....... 563 SRS airbag instructions for Canadian owners (in French) ....... 565...
Page 562: Reporting Safety Defects For U.s. Owners
National Highway Traffic Safety Administration (NHTSA) in addi- tion to notifying Toyota Motor Sales, U.S.A., Inc. (Toll-free: 1-800- 331-4331). If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 563 Seat belt instructions for Canadian owners (in French) The following is a French explanation of seat belt instructions extracted from the seat belt section in this manual. See the seat belt section for more detailed seat belt instructions in English. Utilisation correcte des ceintures de sécurité...
Page 564 AVERTISSEMENT ■ Détérioration et usure des ceintures de sécurité Inspectez le système de ceintures de sécurité régulièrement. Contrôlez l'absence de coupures, d'effilochages et de pièces desserrées. N'utilisez pas une ceinture de sécurité endommagée avant qu'elle ne soit remplacée. Une ceinture de sécurité endommagée ne permet pas de protéger un occu- pant de blessures graves ou mortelles.
Page 565 SRS airbag instructions for Canadian owners (in French) The following is a French explanation of SRS airbag instructions extracted from the SRS airbag section in this manual. See the SRS airbag section for more detailed SRS airbag instruc- tions in English. ◆...
Page 566 ◆ Coussins gonflables latéraux et rideaux SRS Coussins gonflables latéraux avant SRS Participent à la protection du torse des occupants de siège avant Coussins gonflables latéraux arrière SRS Participent à la protection du torse des occupants des sièges latéraux arrière Coussins gonflables rideaux SRS ●...
Page 567 Composants du système de coussins gonflables SRS Capteurs d'impact avant Témoin d'avertissement SRS Système de classification de Contact de boucle de ceinture l'occupant du siège passager sécurité passager avant (ECU et capteurs) avant Ensemble de capteurs de Coussins gonflables genoux coussins gonflables Capteurs d'impact...
Page 568 Votre véhicule est équipé de COUSSINS GONFLABLES INTELLI- GENTS conçus selon les normes de sécurité américaines applicables aux véhicules à moteur (FMVSS208). L'ensemble de capteurs de coussins gonflables (ECU) régule le déploiement des coussins gon- flables sur la base des informations qu'il reçoit des capteurs, etc., indi- qués ci-dessus dans le schéma illustrant les composants du système.
Page 569 AVERTISSEMENT ■ Précautions relatives aux coussins gonflables SRS Respectez les précautions suivantes concernant les coussins gonflables SRS. Le non-respect de ces précautions peut occasionner des blessures graves, voire mortelles. ● Le conducteur et tous les passagers du véhicule doivent porter correcte- ment leur ceinture de sécurité.
Page 570 Un nourrisson ou un enfant trop petit pour utiliser une ceinture de sécurité doit être correctement attaché au moyen d'un siège de sécurité enfant. Toyota recommande vivement d'installer tous les nour- rissons et enfants sur les sièges arrière du véhicule et de prévoir pour eux des systèmes de retenue adaptés.
Page 571 AVERTISSEMENT ■ Précautions relatives aux coussins gonflables SRS ● Ne vous asseyez pas sur le bord du siège et ne vous appuyez pas contre la planche de bord. ● Ne laissez pas un enfant rester debout devant le coussin gonflable passager avant SRS ou s'asseoir sur les genoux du passager avant.
Page 572 AVERTISSEMENT ■ Précautions relatives aux coussins gonflables SRS ● Ne fixez rien et ne posez rien sur des emplacements tels que la planche de bord, la garniture du volant et la partie inférieure du tableau de bord. Ces éléments peuvent se transformer en projectiles lorsque les coussins gon- flables conducteur, passager avant et genoux SRS se déploient.
Page 573 Si les parties renfermant les coussins gonflables SRS, comme les garni- tures du volant et des montants avant et arrière, sont endommagées ou craquelées, faites-les remplacer par votre concessionnaire Toyota. ● Ne placez rien sur le siège du passager avant, comme un coussin par exemple.
Page 574 SRS Ne mettez pas votre véhicule au rebut et ne procédez à aucune des modifi- cations suivantes sans consulter votre concessionnaire Toyota. Les cous- sins gonflables SRS peuvent ne pas fonctionner correctement ou se déployer (se gonfler) accidentellement, provoquant la mort ou de graves blessures.
Page 575: Index
Alphabetical index ..... 579 For information regarding the equipment listed below, refer to “NAV- IGATION AND MULTIMEDIA SYSTEM OWNER’S MANUAL”. • Navigation system • Audio system • Rear view monitor system • Toyota parking assist monitor • Panoramic view monitor • Toyota Entune...
Page 576 Toyota dealer. (→P. 147) ● If you lose your electronic keys, the risk of vehicle theft increases signifi- cantly. Contact your Toyota dealer immediately. (→P. 149) The doors cannot be locked or unlocked ● Is the key battery weak or depleted? (→P. 455) ●...
Page 577 What to do if... (Troubleshooting) If you think something is wrong The hybrid system does not start ● Did you press the power switch while firmly depressing the brake pedal? (→P. 204) ● Is the shift lever in P? (→P. 206) ●...
Page 578 What to do if... (Troubleshooting) A warning buzzer sounds during driving ● The seat belt reminder light is flashing Are the driver and the passenger wearing the seat belts? (→P. 483) ● The parking brake indicator is on Is the parking brake released? (→P. 220) Depending on the situation, other types of warning buzzer may also sound.
Page 579: Alphabetical Index
Alphabetical index Alphabetical index Airbags ........34 Airbag operating conditions ..43 AAC disc Airbag precautions for A/C ..........344 your child......37 Air conditioning filter ..... 448 Airbag warning light ....480 Automatic air conditioning Correct driving posture ... 26 system ........
Page 580 Alphabetical index Alarm .......... 86 Anchor brackets ......56 Back-up lights Antennas Replacing light bulb ..465, 470 (smart key system)....160 Wattage ........ 534 Anti-lock Brake System Battery (12-volt battery) ..424 (ABS) ........283 Battery checking ....424 Warning light......
Page 581 Alphabetical index Child safety ........ 53 12-volt battery Care precautions....426, 517 Aluminum wheels....399 Airbag precautions....37 Exterior ......... 398 Battery precautions..426, 517 Interior........401 Child restraint system ..... 54 Seat belts......402 How your child should wear Cargo capacity......
Page 582 Alphabetical index Clock Coat hooks ....... 378 Daytime running light Compass ........392 system........228 Condenser........ 421 Defogger Console box ......358 Outside rear view Consumption mirrors ........ 348 screen......141, 142 Rear window......348 Coolant Windshield ......348 Capacity........ 530 Dimensions ......
Page 583 Alphabetical index Door lock Doors ........150 ECO Accelerator Guidance ..117 Key........509 Eco drive mode......333 Smart key system ....150 Eco-friendly driving Wireless remote control ..150 information ......115 Doors ........150 Eco guide ......... 117 Automatic door locking Eco score .........
Page 584 Alphabetical index Emergency, in case of Engine coolant If a warning buzzer Capacity........ 530 sounds........ 480 Checking....... 420 If a warning light turns on..480 Preparing and checking If a warning message is before winter ...... 338 displayed ......490 Engine coolant temperature If the 12-volt battery is gauge ........
Page 585 Alphabetical index Front turn signal lights Replacing light bulbs ..461, 470 Flat tire........496 Turn signal lever ....219 Floor mats ........24 Wattage ........ 534 Fluid Fuel Brake ........531 Capacity........ 528 Hybrid transmission ....531 Fuel gauge......96 Washer .........
Page 586 Alphabetical index Hybrid battery (traction battery) ..... 77 Hands-free system Hybrid battery (for cellular phone) (traction battery) air Head restraints ......173 intake vent ....... 78, 450 Head-up display....... 128 Hybrid system......73 Headlights ........ 227 Emergency shut off system ..78 Automatic headlight Energy monitor/ leveling .......
Page 587 Alphabetical index I/M test ........411 Jack ICS (Intelligent Clearance Positioning the jack....415 Sonar)........312 Vehicle-equipped jack ..496 Indicator ........93 Jack handle......496 Warning light......482 Jam protection function Warning messages ....323 Moon roof ......185 Identification Power window ......
Page 588 Alphabetical index Lane Departure Alert with Maintenance steering control (LDA) ..260 Do-it-yourself maintenance... 412 Language (multi- General maintenance ... 407 information display)..108, 124 Maintenance data ....526 LATCH anchors ......67 Maintenance LDA (Lane Departure Alert requirements ...... 404 with steering control)....
Page 589 Alphabetical index Multi-information display......100, 112 Paddle shift switches....216 Drive information....103 Panic mode ......147 Dynamic radar cruise control Panoramic view monitor with full-speed range ..270 Parking brake......220 Eco-friendly driving Parking brake engaged information......115 warning buzzer/ Language......
Page 590 Alphabetical index Rear view monitor system Rear window defogger.... 348 Radar cruise control Refueling ........238 (dynamic radar cruise Capacity........ 528 control with full-speed Fuel types ..... 528, 535 range) ........270 Opening the fuel tank cap..240 Radiator ........421 When the fuel filler door Radio cannot be opened ....
Page 591 Alphabetical index Seat heaters ......353 Seating capacity ...... 201 Safety Connect ......386 Seats......... 169 Seat belt reminder light... 483 Adjustment......169 Seat belts........28 Adjustment precautions ..170 Adjusting the seat belt .... 29 Child seats/child restraint Automatic Locking system installation....
Page 592 Alphabetical index Shift lever ......... 213 Speedometer......96 Hybrid transmission ....213 Sport mode ......333 If the shift lever cannot Steering lock be shifted from P ....217 Column lock release ..... 207 S mode ......... 215 Steering wheel ......175 Shift lock system .....
Page 593 Alphabetical index Fuel door opener switch ..240 Garage door opener Tail lights switches......379 Light switch......227 Ignition switch ....... 204 Replacing light bulbs .... 470 LDA (Lane Departure Alert Talk switch with steering control) Theft deterrent system switch ......... 264 Alarm ........
Page 594 Toyota Entune Trunk light Toyota parking assist Trunk light......157 monitor Wattage ........ 534 Toyota Safety Sense P .... 242 Turn signal lights Automatic High Beam ... 230 Replacing light Dynamic radar cruise control bulbs....461, 467, 470 with full-speed range ..270 Turn signal lever ....
Page 595 Alphabetical index Electric power steering ..481 ICS OFF indicator....482 Vanity lights ......364 LDA indicator ......481 Wattage ........ 534 Low fuel level......483 Vanity mirrors ......364 Malfunction indicator lamp..480 Vanity lights ......364 Master warning light ..... 483 Vehicle data recording ....
Page 596: Gas Station Information
13 gal. (49.3 L, 10.8 Imp. gal.) (Reference) Fuel type P. 528, 535 Cold tire inflation P. 532 pressure Engine oil capacity (Drain and refill — P. 529 reference) “Toyota Genuine Motor Oil” or equivalent Engine oil type P. 529...

Toyota Camry Hybrid 2018 Owner's Manual

Quick Links

Related Manuals for Toyota Camry Hybrid 2018

Summary of Contents for Toyota Camry Hybrid 2018

Table of Contents