♦ Automatic power on function; ♦ Main unit and microphone key lock function; ♦ 5Tone signaling for data transfer,alarm, all call, ANI, remote kill, remote waken. ♦ DTMF-ANI or 5Tone-ANI for automatical calling recognition; ♦ Scrambler(Optional). RT95 UHF/VHF Two Way Radio...
2. ACCESSORIES 2.1 Standard Accessories FUNC Microphone Transceiver Pads Mobile Bracket Screws DC Power Cable Adjusting screws non-slip mat Fuse(10A 250V) with Fuse Holder 2.2 Optional Accessories PC cable Car Antenna RT95 UHF/VHF Two Way Radio...
24V battery. Be sure to use a 12V vehicle battery that has sufficient current capacity. If the current to the transceiver is insufficient, the display may darken during transmission, or transmitting output power may drop excessively. RT95 UHF/VHF Two Way Radio...
Page 7
♦ Do not directly connect the transceiver to an AC outlet. ♦ Use the supplied DC power cable to connect the transceiver to a regulated power supply. ♦ Do not substitute a cable with smaller gauge wires. RT95 UHF/VHF Two Way Radio...
Page 8
» If you use the transceiver for a long period when the vehicle battery is not fully charged, or when the engine is OFF, the battery may become discharged, and will not have sufficient reserves to start the vehicle. Avoid using the transceiver in these conditions. RT95 UHF/VHF Two Way Radio...
» External speaker adopt double port BTL, please care about the connecting way. The speaker can not connect with the ground, otherwise the speaker will be fault. The wrong connecting way as the following picture. RT95 UHF/VHF Two Way Radio...
Page 10
Error Ground 3.4.2 Microphone For voice communications, connect a microphone equipped with an 8-pin modular plug into the modular socket on the front of the main unit. Press irmly on the plug until the locking tab clicks. FUNC Microphone connector http://radioaficion.com/hamfiles/...
Self define key Self define key Self define key Self define key Self define key Function key/ function group key Microphone Jack Channel switch/Push button/Key lock LCD display Display channel/frequency/function setting 4.2 Rear panel EXT SP RT95 UHF/VHF Two Way Radio...
Page 12
Functions Antenna connector Connect a 50 ohm antenna Ex-Speaker Jack Connect external speaker Power cable Connect a standard DC power cable 4.3 Display 11 12 13 14 18 19 20 21 22 Functions Displays the self define function when press P1 Displays the self define function when press P2 Displays the self define function when press P3 Displays the self define function when press P4...
Page 13
When this key is in up position, It is unlock UP/DOWN key, when Lock UP/DOWN this key is in down poisition, UP/DOWN key will be locked MIC Connector Diagram(in the front view of connector) Key Pad Serial Data DOWN MIC GND RT95 UHF/VHF Two Way Radio...
» If transceiver programmed as professional transceiver mode and locked, you can't return to amateur transceiver mode by manual operation from general setting. 4.Under any mode, the FUNC MENU setting can be changed and saved. RT95 UHF/VHF Two Way Radio...
6. BASIC OPERATIONS 6.1 Switching the Power On/Off 1. Power On: in power off state press , the LCD displays " RETEVIS " then will displays current frequency or channel. for 2 seconds, the LCD displays "CLOSING", 2. Power Off: in power on state, press then the LCD display disappears.
Page 16
5. Turn the channel knob or microphone [UP]/[DOWN] key to choose the channel number to be stored. 6. Hold the [PX] key defined as V/M function to confirm and store the channel, the channel number stop flash and radio emits a beep sound, the channel is stored successfully. RT95 UHF/VHF Two Way Radio...
LCD displays DCS, long press this key to enter DCS scan, turn channel knob or press microphone [UP]/[DOWN] key can change scan direction. Once finding a matching DCS signaling, it will stop 5 seconds then scan again, press any key to exit DCS scan. RT95 UHF/VHF Two Way Radio...
2. Long press [PUSH] button again, the downside LCD displays : Key Unlock, means the keypad is unlocked. » NOTE:When keypad lockout, except key, [PUSH] button and [PTT] key is available, other keys are invalid . RT95 UHF/VHF Two Way Radio...
2. Press [PUSH] button, the menu value in LCD turns to green color. 3. Turn channel knob to choose wanted setting. Total 9 Channel step size available: 2.5K,5K,6.25K,10K,12.5K,20K,25K, 30K and 50K. 4. Press [PUSH] button or [P3] key to store setting and exit. RT95 UHF/VHF Two Way Radio...
4. Press [PUSH] button or [P3] key to store setting and exit 7.7 Scan Dwell Time Setup 1. Enter FUNCTION MENU list, choose No.07 function. 2. Press [PUSH] button, the menu value in LCD turns to green color. 3. Turn channel knob to choose wanted setting. RT95 UHF/VHF Two Way Radio...
Page 21
2. Press [PUSH] button, the menu value in LCD turns to green color. 3. Turn channel knob to choose brightless level, 1-3 level available. 4. Press [PUSH] button or [P3] key to store setting and exit. RT95 UHF/VHF Two Way Radio...
2. Press [PUSH] button, the menu value in LCD turns to green color. 3. Turn channel knob to choose wanted setting FAIL: Revers display STAN: normal display 4. Press [PUSH] button or [P3] key to store setting and exit. RT95 UHF/VHF Two Way Radio...
Page 23
3. Turn channel knob to choose wanted setting ALL: All channel, signaling function setup resume factory default. OPT: All function menu setup resume factory default except CHAN MENU. 4. Press [PUSH] button or [P3] key to store setting and exit RT95 UHF/VHF Two Way Radio...
5. Press [PUSH] button or [P3] key to store setting and exit. 8.3 HIGH/MID/LOW Power Selection 1. Enter CHAN MENU, choose No.3 function 2. Press [PUSH] button, the menu value in LCD turns to green color RT95 UHF/VHF Two Way Radio...
Page 25
CDT:You can hear the calling when receive a matchng carrier and CTCSS or DCS signaling TONE: You can hear the calling when receives matching carrier + optional signaling. C&T: You can hear the calling when receives matching carrier + CTCSS/DCS + optional signaling. RT95 UHF/VHF Two Way Radio...
1. Enter CHAN MENU list, choose No.10 function 2. Press [PUSH] button, the menu value in LCD turns to green color. 3. Turn channel knob to choose wanted setting, press [FUNC] key to set the offset direction. RT95 UHF/VHF Two Way Radio...
4. Press [PUSH] button or [P3] key to store setting and exit 8.14 OWNID (SELF ID ENQUIRY) 1. Enter CHAN MENU list, choose No.14 function; 2. The LCD will display current channel DTMF ID or 5Tone ID. RT95 UHF/VHF Two Way Radio...
[PUSH] button to enter value setting. the menu value in LCD turns to green color 4. Turn channel knob to choose wanted setting. 5. Press [PUSH] button or [P3] key to store setting and exit. RT95 UHF/VHF Two Way Radio...
300MS: The time for transmit a single DTMF encode and the interval is 300MS, 500MS: The time for transmit a single DTMF encode and the interval is 500MS. 4. Press [PUSH] button or [P3] key to store setting and exit. RT95 UHF/VHF Two Way Radio...
USB cable. then reinsert USB cable and open software, then rechoose COM Port, it will turn into normal operation. Therefore, please connect transceiver with computer after switching on the transceiver. Don't restart transceiver power when it is connected with computer. RT95 UHF/VHF Two Way Radio...
Antenna connector has debris or damaged. Whether set Low power a. Frequency/channel different, pls modify Can not talk with other b. CTCSS/DCS different, pls reset members within the group c. Out of the communication range RT95 UHF/VHF Two Way Radio...