Table of Contents
Advertisement
Quick Links
Quick Installation Guide
AIRNET 54 Mb CPE Bridge Point to Point Kit
Series
Package Contents:
• 2 Netkrom CPE units
• Two Mounting bracket include: 2 stainless steel U-Bolt, 2 mounting brackets, 2
pipe Brackets and 4 screw nuts
• Two PoE Injectors
• Two Power Cables
• Two RJ45 Waterproof Connector System
• CD-ROM
• Two 75' Outdoor Rated Cat5e shielded cables
Advertisement
Table of Contents
Summary of Contents for Netkrom AIR-PT900L
-
Page 1: Quick Installation Guide
AIRNET 54 Mb CPE Bridge Point to Point Kit Series Package Contents: • 2 Netkrom CPE units • Two Mounting bracket include: 2 stainless steel U-Bolt, 2 mounting brackets, 2 pipe Brackets and 4 screw nuts • Two PoE Injectors •... - Page 2 Warnings • Do not work on the system or connect or disconnect cables during periods of lightning activity. • NETKROM shall not be liable for incidental or consequential damages resulting from the furnishing, performance, or use of this manual. • Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits.
-
Page 3: Package Contents
Package contents Kit Point to Point Take a moment to ensure you have all of the following parts in your Outdoor Waterproof Unit installation kit before you begin installing the product. If any parts are missing, please contact your local vendor or contact us, please see the contact information in Section... -
Page 4: Setup Requirements
Setup Requirements Before starting, please verify that the following is available: • CAT5/5e or FTP Outdoor Ethernet cable (from the CPE to PoE Injector) • At least one computer is installed with a Web browser and a wired or wireless network interface adapter •... - Page 5 CPE. Then connect the other end of the cable to the PoE injector. For the Netkrom PoE, the recommended length of the Category 5 cable is up to 260 feet or 80 meters. 1.- Remove the thin enclosure nut enclosure nut from the feedthru assembly.
- Page 6 PC. Step 3 Connect the power cable supplied in the Netkrom PoE kit to the mainelectrical supply and the power plug into the socket of the injector. Now, turn on your power supply. Notice that the POWER LED has lighted up.
- Page 7 Mounting the Outdoor CPE in a Pole or Tower Netkrom CPE device can be mounted on the pole or tower as shown in following: 1.-Attach the mounting bracket to the back of the CPE using the three hex screws provided. (Do not over tighten the screws.)
- Page 8 uConfig is a feature that provides the ability to directly access the CPE without the need to know absolutely its IP address. It may be run directly from the product CD or installed on the user’s PC for later access. Using uConfig When you execute the uConfig file you should see a window as it is shown on the...
- Page 9 Click the O K button to continue The default browser will be loaded using the correct IP address of the CPE (regardless of how the computer’s TCP/IP properties are set), Default Password: password , and start configuring the Click on radio.
- Page 10 If you don’t use the uConfig Utility you need to establish Ethernet connection between your PC and the CPE, by default the CPE has the IP address 192.168.168.1. Therefore, your PC must be in the same network segment as the CPE is to get Ethernet connectivity. tep 1 o to Start button, then go to My Network laces and finally click on Network...
-
Page 11: Getting Started
Find below typical and basic configurations using the CPE. For advanced features please refer to the user manual. Getting Started You can start configuring your CPE using either your Web Browser or the uConfig utility. Address bar, enter http://192.168.168.1 and press Enter on your keyboard. - Page 12 Wireless Point to Point Setup The CPE Bridge Point to Point Kit is commonly used Point-to-Point Applications. implement Point-to-Point onnection by simply setting one access point RootAP in Access Point mode and setting the other access point in Trans parent Client mode or in Client Mode.
- Page 13 Follow these steps to setup Transparent Client/s. Step 1 elect the Remote AP MAC checkbox. Enter the Remote AP MAC. Check the MAC address of your Remote AP under About system >> Wireless MAC. Ensure that The Current Mode is set to Transparent Client.
- Page 14 900 MHz Channel Conversion ( AIR-PTP900L ) In order to use your 900 MHz CPE, you have to select in Wireless Profile any of the following options: 802.11b only 802.11g only 802.11b/g mixed (recommended) 802.11 b/g 900 MHz Channel 10 (2457) 913 MHz Channel conversion from 2.4 GHz to Channel 11 (2462)
- Page 15 1. - Advanced Routing Configuration: Please go to page 85 of User Manual. . – Bandwid th Control: Please go to page 95 of User Manual. 3. – Remote Management: Please go to page 99 of User Manual. 4. – Advanced Wireless Configuration: Please go to page 114 of User Manual.
-
Page 16: Contact Information
5930 NW 99th Avenue Unit 14, El Doral, Miami FL 33178 Phones: (+1) 305-418-2232 Fax: (+1) 305-418-9266 Sales and ordering: American Customers: salesusa@netkrom.com Worldwide Customers: sales@netkrom.com Latin American and Spanish Customers: ventas@netkrom.com Technical Support : Worldwide and English Customers: support@netkrom.com Latin American Customers: soporte@netkrom.com...