What To Do If - Elektrabregenz KFI 2140-1 Operating And Installation Instructions

What to do if ...

Correcting Malfunctions
A malfunction may be caused by only a minor fault
that you can rectify yourself using the following
instructions. Do not perform any other work on the
appliance if the following information does not pro-
vide assistance in your specific case.
Malfunction
Appliance is not switched on
Mains plug is not plugged in or is loose.
Fuse has blown or is defective
Appliance does not work.
Socket is defective.
Temperature is set too cold.
Appliance cools too much
Temperature is not properly adjusted.
Door was open for an extended period.
The food is too warm.
.
A large quantity of warm food was placed in
the appliance within the last 24 hours.
The appliance is near a heat source.
Light bulb is defective.
Interior lighting does not work.
Door seal is not air tight (possibly after chan-
ging over the hinges).
Heavy build up of frost, possibly also on the
door seal.
Appliance is not level.
The appliance is touching the wall or other
objects.
Unusual noises.
A component, e.g. a pipe, on the rear of the
appliance is touching another part of the
appliance or the wall.
The compressor does not start immediately This is normal, no error has occurred.
after changing the temperature setting.
Water on the floor or on storage shelves. Water drain hole is blocked.
26
Warning! Repairs to refrigerators/freezers may
only be performed by qualified service engineers.
Improper repairs can give rise to significant
hazards for the user. If your appliance needs repai-
ring, please contact your specialist dealer or our
Customer Service.
Possible Cause Remedy
Switch on the appliance.
Insert mains plug.
Sicherung überprüfen, gegebenenfalls
erneuern.
Mains malfunctions are to be corrected by an
electrician.
Turn the temperature regulator to a warmer
setting temporarily..
Please look in the "Initial Start Up" section.
Open the door only as long as necessary.
Turn the temperature regulator to a colder set-
ting temporarily.
Please look in the "Installation location" sec-
tion.
.
Please look in the "Changing the Light Bulb"
section.
Carefully warm the leaking sections of the
door seal with a hair dryer (not hotter than
approx. 50 °C). At the same time shape the
warmed door seal by hand such that it sits
correctly.
Readjust the feet.
Move the appliance slightly.
If necessary, carefully bend the component out
of the way.
The compressor starts after a period of time.
See the "Cleaning and Care" section.
Die Abdeckung (Hc) in die Schiene (Ha) eindrücken,
bis sie einrastet.
Gerätetür und Möbeltür auf ca. 90° öffnen. Den
Winkel (Hb) in der Schiene (Ha) einsetzen.
Gerätetür und Möbeltür zusammenhalten und die
Bohrlöcher anzeichnen (siehe Abb.).
Die Winkeleisen entfernen und 8 mm vom äusseren Rand
der Tür mit dem Nagel (K) kennzeichnen.
Den Winkel wieder auf der Schiene anbringen und
mit den mitgelieferten Schrauben befestigen.
Für eine allfällig notwendige Ausrichtung der
Möbeltür, den Spielraum der Langlöcher nutzen.
Nach Beendigung der Arbeiten den einwandfreien
Verschluß der Gerätetür überprüfen.
Die Abdeckung (Hd) in die Schiene (Hb) eindrück-
en, bis sie einrastet.
Ha
Hc
PR33
8mm
Ha
Hb
PR167
8mm
K
Ha
Hb
PR168
Hb
Hd
PR167/1
7