SAFETY CONSIDERATIONS FCC Cautions Remember to exercise good common sense THIS DEVICE COMPLIES WITH PART 15 OF THE when using the Home Automation features of FCC RULES. OPERATION IS SUBJECT TO THE your remote - especially when scheduling FOLLOWING TWO CONDITIONS: unattended devices.
Setting Up Your Remote to Send RF ......15 that represents the channel. Using The Remote ............19 Favorite Key ..............20 The IR27A IconRemote can also control X10 RF Mode Key ................. 21 devices, which allows you to control different X10 RF Devices ............21 electrical devices located in various physical QuickPower ..............
Hard Key Functions Hard Key Functions, cont. HIS/HERS - Quick access keys for favorites stored under His/Hers groups. SIDE KEYS - Used to access on-screen features. LCD - (Liquid Crystal Display). MODE - Selects mode (TV, VCR, etc.) for the remote. HOME - The starting screen on the LCD for most operations.
Setup Using the Wizard Battery Installation After you insert the batteries and choose “English” the Setup Wizard screen (1) appears. You can exit the Wizard at any • On the back of the remote, push down time by pressing the HOME key (located on the tab and lift the cover off.
Setting Up Your Devices Setting Up Your Devices, cont. How to set up a TV Pressing Save displays screen (5) that instructs you to try a few other keys on the remote to make sure you’ve found the After you’ve been through the Wizard for correct code.
Setting Up Your Favorites Setting Up Your Favorites, cont. Once you’ve gone through the Wizard If you want to add a label to the logo press the Side Key next and set up at least a TV, and set up more to Label.
Setting Up X10 Devices Note: “Triple tap” name entry works in a similar fashion to text The IR27A IconRemote - coupled with other X10 Home entry on a cell phone. Tap each numeric key to cycle through Automation Modules - gives you the ability to control every- ALL caps, numbers, and lower case letters.
Setting Up X10 Devices, cont. Setting Up X10 Devices, cont. When triggering an X10 module or wall switch from a remote In the following example we’ll set up the remote for a LM465 control, the signal is typically sent from the remote using RF Lamp Module located in the “Basement.”...
Setting up a LM465 Lamp Module (example) have set up some devices and some favorites, you can now use The following is a basic example of how to set up an X10 the remote. See the sections that follow to set up more devices Lamp Module (sold separately).
X10 RF Devices channel 1. Watch the flickering halo at the bottom left of the screen, it Selecting X10 from the MODE key flickers for each digit sent. It also shows what device is being screen displays the Pick Group screen.
QuickPower Sleep QuickPower is a way of quickly turning Sleep lets you set any device to turn off a all your devices on or off from one easy preset time from now. You can set the off to use screen. time in increments of 15 minutes, up to a Maximum of 90 minutes.
Learning Learning, cont. • Check the IR transmitters/sensors are correctly aligned Tips On Learning between the two remotes. • Adjust the distance between the two remotes to be closer a. Some functions from some types of remotes might not (e.g. half an inch) or a further away (e.g., 2 inches) from be able to be learned.
Learning Main Keys Learning Main Keys, cont. At the Home screen press the Side Key You then press and hold (in this example) next to Learn. the Power key on the other remote, until the display shows that the command has been successfully learned.
Macros - Main Keys, cont. Learning Side Keys Before learning the second key in the At the Home screen press the Side Key Macro, you can if desired, set a delay next to Learn. (1-10 secs) after which the command stored in the Macro will be sent.
Learning Side Keys, cont. Learning Side Keys, cont. Next point the remote you want to learn E.g., in this example we pressed the 3 commands from at the bottom of the key on the remote to enter the letter D. IR27A IconRemote, and press OK when Then we pressed the 8 key repeatedly you’re ready.
Learning Macros (Side Keys) Learning Macros, cont. A Macro could include the Power key for Line up the remotes and press OK when your TV, followed by the Power key for you’re ready. your Cable box, followed (after a 2 second delay), by digit 4 from your cable remote.
Learning Macros, cont. Setting up more Point your existing remote at the bottom Setting up more Devices of the IR27A IconRemote and press OK when you’re ready. Then press your next When you first inserted the batteries in the key. remote you likely went through the Wizard and set up a few devices.
Setting up more, cont. Setting up more, cont. Setting up more Favorites Adding/Editing Favorites When you first inserted the batteries in the This lets you add favorites to an existing remote you likely went through the group, edit favorites in an existing group, Wizard and set up a few favorites.
Setting up more, cont. Setting up more, cont. Reordering Favorites Deleting Favorites This lets you move the favorites that you This lets you delete favorites that you previously set up in a group, to different previously set up in a group. locations on the screen, i.e., reorder them.
Setting up more, cont. Setting up more, cont. Renaming Favorite Groups Clearing Settings in the Remote This lets you Rename the groups that you This lets you clear (erase) various things save your favorites in. For example you you’ve set up in the remote. might want to rename His to Dave, or Hers to Isabel.
Advanced Settings Advanced Settings, cont. You can also change the device type by pressing the key on Press the HOME key, then select Setup, then select Advanced. screen (1) next to the device that you are editing the code for. Pressing this key repeatedly cycles through all available device The screen to the right lets you change the types.
Advanced Settings, cont. Advanced Settings, cont. Punchthrough, cont. KidSafe At this screen you set how you want the Press the HOME key, then select Setup, Volume Up/Down and Mute keys to then select Advanced, then KidSafe. operate when the remote is in TV mode. The first time you access the KidSafe Then select how you want the Channel Up/ menu you are asked if you want to set up...
If you own or have purchased the Model IR543 Command The IR27A IconRemote used in conjunction with the UX25A Center, and you have compatible X10 Lamp, Appliance, and receiver gives you control of Audio and Video components - Wall Switch modules, you will also be able to control lights even if they are in a different room from the remote.
(1) year from the original date of etc., when you set up each favorite. See Add/Edit Favorites purchase at retail. X10 agrees to repair or replace, at its sole page 37 to change the device type for your favorite(s).
X10.com, a Division of X10 Wireless Technology, Inc. 3824 North 5th St., Suite C, North Las Vegas, NV 89032 Web Site: http://www.x10.com IR27A-4/08...