Related Manuals for dji Datalink Pro
Summary of Contents for dji Datalink Pro
- Page 2 DJI Technology Co., Ltd. and its affiliated companies assume no liability for damage s or injuries incurred directly or indirectly from using, installing or refitting this product improperly, including but not limited to using non‐designated accessories. DJI is the registered trademark of SZ DJI Technology Co., Ltd. abbreviated as DJI . Names of products, brands, etc., appearing in this manual are trademarks or registered trademarks of their respective owner companies. This product and manual are copyrighted by DJI with all rights reserved. No part of this product ...
- Page 3 Disclaimer ........................................ Warnings ........................................ About .......................................... Part Description * ...................................... Installation and Connection .................................. Usage .......................................... Linking Procedures .................................. Configuring Parameters Using the DJI Assistant ...................... Using the DJI Ground Station .............................. Working Status LED .................................. Appendix ........................................ Specifications ..................................... Compliance Information .................................. FCC Compliance Notice .................................. ...
- Page 4 The Datalink Pro is used for wireless data transmission, including communication between the Mobile Station and Base Station. There are M and M versions to meet the requirements of different regions. The multi‐functional bidirectional transmission link is perfect for the DJI A flight control system, D‐RTK and Ground Station. Use frequency bands of near MHz and MHz to avoid radio interference with the DJI Lightbridge and remote controller. Support for multiple interfaces, such as USB, CAN and UART, offers ...
- Page 5 M and M Datalink Pro use different antennas but have the same functions. Installation and Connection The following uses the M Datalink Pro, DJI Matrice , D‐RTK and DJI Intelligent Flight Battery to illustrate a typical installation and connection. Attach the Base Station antenna and install it on the D‐RTK Ground System’s base board with a screw included with the D‐RTK product . Then connect the Base Station and the D‐RTK Ground System via an ‐pin cable. Install the Mobile Station to the DJI Matrice with double‐sided tape. Attach the antennas to the ...
- Page 6 Enable the D‐RTK Ground System’s battery to power on the Datalink Pro Base Station. Hold the Base Station’s Linking Button for about seconds to enter the linking mode with the Working Status LED blinks red and green alternatively. Enable the D‐RTK Ground System’s battery to power on the Datalink Pro Mobile Station. Hold the Mobile Station’s Linking Button for about seconds and wait for linking. The Base Station and Mobile Station will connect with each other if successfully linked. Follow procedures – to link other Mobile Stations to set up a single‐to‐multiple system. Configuring Parameters Using the DJI Assistant DJI Assistant should be used to upgrade the Datalink Pro. Full Duplex Mode and Broadcast Mode can be switched in DJI Assistant Download DJI Assistant from www.dji.com and install it on your computer. Toggle the ‐position switch to the COMBO_SW position, connect the Base Station to the computer with DJI Assistant launched, and then configure parameters according to the message prompts. ...
- Page 7 Supports Windows or later or Mac OS X . or later . Using the DJI Ground Station Ensure the A Flight Control System, Datalink Pro and D‐RTK are connected correctly before powering on. Connect the Base Station to the PC via a Micro USB cable, and then run the Ground Station. Enable the D‐RTK Ground System’s battery to power on the Datalink Pro Base Station first. Enable the D‐RTK Ground System’s battery to power on the Datalink Pro Mobile Station. Note: The DJI Ground Station supports up to five Air Systems in Full Duplex Mode. The ‐position switch should be set to the COMBO_SW position. Download the User Manual from www.dji.com to learn more. Refer to the DJI Ground Station User Manual for details if using the DJI Ground Station. Working Status LED LED Description Blinking Red Parameter error after powering on. If not resolved by power ...
- Page 8 Mobile Station: . W Base Station: . W Base Station: . W Features Frequency Band MHz China: ‐ Taiwan: ‐ FCC: South Korea: Canada: 2‐ ‐ Australia: 2‐ Japan: . ‐ . 5‐ Serial Data Rate Max. Antenna Options Vertically polarized Supported Interfaces USB, UART, CAN Supported DJI Products A , D‐RTK, Ground Station...
- Page 9 Operating Temperature ° to °F ° to Storage Temperature ‐ ° to °F ‐ ° to °C Humidity % to %, non‐condensing °C Dimension without Antenna Base Station: mm x mm x . mm Mobile Station: mm x . mm x . mm Weight without Antenna Base Station: g Mobile Station: g Power Supply ...
- Page 10 電機須忍受合法 法通信 或工 工業 科學及醫 醫療用電波輻射 射性電機設備之 EU C ompliance Stat tement SZ D DJI TECHNOLO OGY CO., LTD . hereby decl ares that this s device is in n compliance with the ess ential requ uirements and o other relevant t provisions of the R&TTE Dir rective. ...
- Page 11 EU contact address: DJI GmbH, Industrie Strasse. , , Niederlauer, Germany 制 造 商 深圳市大疆创新科技有限公 地 址 深圳市南山区高新南四道18 创维半导体设计大厦西座14层 服 热线 400-700-0303 Manufactured by: th floor, West Wing, Skyworth Semiconductor Design Building NO. Gaoxin South th Ave, Nanshan District, Shenzhen, Guangdong, China ...
Need help?
Do you have a question about the Datalink Pro and is the answer not in the manual?
Questions and answers