Unimac CB200 User Manual

Unimac CB200 User Manual

Three-in-one air brad nailer

Advertisement

Three-in-One Air Brad Nailer
User Manual
[Revision 2.0 April 2017]
READ THIS MANUAL CAREFULLY BEFORE USE AND KEEP FOR FUTURE REFERENCE – FAILURE TO DO
SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY VOID WARRANTY. • Products covered by this
manual may vary in appearance, assembly, inclusions, specifications, description and packaging.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CB200 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Unimac CB200

  • Page 1 Three-in-One Air Brad Nailer User Manual [Revision 2.0 April 2017] READ THIS MANUAL CAREFULLY BEFORE USE AND KEEP FOR FUTURE REFERENCE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY VOID WARRANTY. • Products covered by this manual may vary in appearance, assembly, inclusions, specifications, description and packaging.
  • Page 2 Loading Fasteners............................4 OPERATING INSTRUCTIONS ............................5 Using the Nailer ............................. 5 Clearing a Jammed Fastener ........................5 REGULAR MAINTENANCE ............................5 TROUBLESHOOTING ..............................6 EXPLODED PARTS DRAWING ............................7 PARTS LIST ................................. 8 SPECIFICATIONS ................................ 10 E&OE © 2017 Unimac...
  • Page 3 Use the correct air connector. The connector on the nail gun must not hold pressure when the air supply is disconnected. If the wrong fitting is used, the nail gun can be charged with air after being disconnected and still be able to drive a fastener. E&OE © 2017 Unimac...
  • Page 4 The warnings and instructions explained in this instruction manual cannot cover all possible conditions and situation that may occur. Common sense and caution are factors which cannot be built into this product and must be supplied by the operator. E&OE © 2017 Unimac...
  • Page 5 Never operate the nail gun unless the safety nose is in contact with the work piece. Do not operate the nail gun without fasteners, this will cause damage to the nailer. Never fire fasteners into the air because this may cause injury to the operator or others. E&OE © 2017 Unimac...
  • Page 6: Operating Instructions

    O-ring and other tool parts do not soak unless necessary). • Check if there are worn and damaged parts. • Inspect trigger and safety mechanism to assure the system is complete and functional; no loose or missing parts, no binding or sticking parts. E&OE © 2017 Unimac...
  • Page 7: Troubleshooting

    Use recommended fasteners space of nail housing Wrong size of fasteners Use recommended fasteners Fasteners are jammed Damaged or worn out driver guide Check and replace the driver Magazine or nose screw loose/dirty Tighten and clean the magazine E&OE © 2017 Unimac...
  • Page 8 Three-in-One Air Brad Nailer Exploded Parts Drawing E&OE © 2017 Unimac...
  • Page 9: Parts List

    Screw 4*38 A.00.05.0041 Ring A.00.06.0061 Step pin A.04.09.XXXI Body A.00.11.0031 Pin 2*11 A.03.10.0141 Nozzle A.07.08.0241 Steel bar A.05.05.0011 Seal, air A.01.00.0032 Spring A.05.03.0011 Upper remote housing A.02.00.1351 O-ring 3*1.25 (red) A.OI.04.0011 Spring A.07.06.0011 Spring holder (white) E&OE © 2017 Unimac...
  • Page 10 Upper mag A.00.06.0541 A.07.01.0861 Lower mag A.D7.11.0451 Catch guide plate A.07.01.8715 Guide plate A.00.11.0191 Pin 3*24 A.02.04.0371 Grip A.02.00.0661 O-ring 37.5*3.55 A.00.05.0061 E-ring 2.5 A.10.01.XXX1 Tail cover B.07.01.0841 Clip assembly A.03.07.XXXX Air plug A.02.04.0031 Grip A.OS.00.0421 spacer E&OE © 2017 Unimac...
  • Page 11: Specifications

    9040 Narrow Crown Staples - 18 Ga. 10-40mm Nail Capacity 100 pcs. Product Dimension (L x W x H) 250 x 60 x 250mm Product Weight 1.2kg Fasteners are standard and can be purchased at hardware Note stores E&OE © 2017 Unimac...
  • Page 12 ©2017 Unimac. All rights reserved. No part of this document, including descriptive content, concepts, ideas, diagrams or images may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, scanning or recording, or any information storage and retrieval system, without express permission or consent from the publisher.

Table of Contents