Table of Contents
Advertisement
Quick Links
100psi Pneumatic 2 in 1 Nailer
User Manual
[Revision 2.0 April 2017]
READ THIS MANUAL CAREFULLY BEFORE USE AND KEEP FOR FUTURE REFERENCE – FAILURE TO DO
SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY VOID WARRANTY. • Products covered by this
manual may vary in appearance, assembly, inclusions, specifications, description and packaging.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Unimac NAL-FLOOR
Summary of Contents for Unimac NAL-FLOOR
- Page 1 100psi Pneumatic 2 in 1 Nailer User Manual [Revision 2.0 April 2017] READ THIS MANUAL CAREFULLY BEFORE USE AND KEEP FOR FUTURE REFERENCE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY VOID WARRANTY. • Products covered by this manual may vary in appearance, assembly, inclusions, specifications, description and packaging.
-
Page 2: Table Of Contents
Clearing a Jammed Fastener ........................7 MAINTENANCE ................................8 Clean and Inspect Daily ..........................8 Service and Repairs ............................8 TROUBLESHOOTING ..............................8 IN THE BOX .................................. 9 EXPLODED DRAWING OF PARTS ..........................10 PARTS LIST ................................. 11 E&OE © 2017 Unimac... -
Page 3: Important Safety Instructions
Make sure that all screws and caps are securely tightened. 11. DO NOT USE TOOL WITHOUT SAFETY WARNING LABEL. If label is missing, damaged or unreadable, contact your Service Centre for a replacement. See Figure 6. E&OE © 2017 Unimac... -
Page 4: E&Oe © 2017 Unimac
17. FIRE FASTENERS INTO WORK SURFACE ONLY. Never fire into materials that are too hard to penetrate. 18. DO NOT DRIVE FASTENERS on top of other fasteners. The fasteners can ricochet, causing personal injuries. See Figure 10. E&OE © 2017 Unimac... -
Page 5: Product Specifications
WARNING: All airline components (hoses, connectors, filters, regulators, etc.) must have a minimum working pressure rating of 150 PSI (10.3BAR) or 150% of maximum system potential, whichever is higher. E&OE © 2017 Unimac... -
Page 6: Preparing The Tool
WARNING: Keep tool pointed away from yourself and others at all times. Always connect tool to air supply before loading fasteners. Always wear Z87 approved safety glasses and hearing protection when preparing or operating the tool. Never use a tool that leaks air or needs repair. E&OE © 2017 Unimac... -
Page 7: Using The Tool
This procedure should be followed before each job due to variations in flooring and was designed for installing both unfinished and tool conditions. E&OE © 2017 Unimac... -
Page 8: Clearing A Jammed Fastener
4. Slide out the Driver Guide Plate and Gate assembly. See Figure 26. 5. Pull the Driver Guide Plate and Gate assembly apart and remove the Jammed Fastener. See Figure 27. 6. Replace the Driver Guide Plate and Gate with three screws. E&OE © 2017 Unimac... -
Page 9: Maintenance
Air is leaking near the Loose screws. Tighten screws. bottom of the tool. Worn or damaged O-rings or Install “OVERHAUL” bumper. Maintenance Kit. Tool is jamming frequently. Incorrect fasteners. Verify for approved fasteners of correct size. E&OE © 2017 Unimac... -
Page 10: In The Box
In the Box When unpacking, check to make sure that all the parts are included. If any parts are missing or broken, please contact the seller. 1X 2 in 1 UNIMAC Nailer/Stapler 1X S3 Hex Key 1X S4 Hex Key... -
Page 11: Exploded Drawing Of Parts
100psi Pneumatic 2 in 1 Nailer Exploded Drawing of Parts E&OE © 2017 Unimac... -
Page 12: Parts List
Fixed magazine B O-ring 58.7 x 3.5 Bushing Bumper Spring Seal Movable magazine Air plug Hex key Sleeve Sheath Screw Rail A Guide body Oriented plate Rail B Front plate Sleeve Screw Stopped plate B Screw Pull handle E&OE © 2017 Unimac... - Page 13 ©2017 Unimac. All rights reserved. No part of this document, including descriptive content, concepts, ideas, diagrams or images may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, scanning or recording, or any information storage and retrieval system, without express permission or consent from the publisher.
Need help?
Do you have a question about the NAL-FLOOR and is the answer not in the manual?
Questions and answers