Table of Contents
Advertisement
Quick Links
Pneumatic Air Coil Nailer
User Manual
[Revision 2.0 April 2017]
READ THIS MANUAL CAREFULLY BEFORE USE AND KEEP FOR FUTURE REFERENCE – FAILURE TO DO
SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY VOID WARRANTY. • Products covered by this
manual may vary in appearance, assembly, inclusions, specifications, description and packaging.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Unimac CB700
Summary of Contents for Unimac CB700
- Page 1 Pneumatic Air Coil Nailer User Manual [Revision 2.0 April 2017] READ THIS MANUAL CAREFULLY BEFORE USE AND KEEP FOR FUTURE REFERENCE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY VOID WARRANTY. • Products covered by this manual may vary in appearance, assembly, inclusions, specifications, description and packaging.
-
Page 2: Table Of Contents
Firing Fasteners ............................8 Clearing a Jammed Fastener ........................9 MAINTENANCE ................................10 Clean and Inspect the Tool Daily ......................... 10 Service and Repairs ............................ 10 TROUBLESHOOTING ..............................11 EXPLODED PARTS DRAWING ..........................13 PARTS LIST ................................14 E&OE © 2017 Unimac... -
Page 3: Important Safety Instructions
8. Do not connect the tool to pressure levels that potentially exceed 180 PSI (12.3 BAR). 9. Use only an air hose that is rated for 150% of the maximum system pressure. Please try to use a hose of ID 3/8” connecting nailer with compressor. E&OE © 2017 Unimac... - Page 4 If the safety bracket is allowed to contact the work surface again before the trigger is released, an unwanted fastener will be fired. E&OE © 2017 Unimac...
- Page 5 29. When not in use, tool should be cleaned and put back into the packaging box. For safety reasons, keep out of reach of children. E&OE © 2017 Unimac...
-
Page 6: Fastener Specifications
Pneumatic Air Coil Nailer Fastener Specifications Only use recommended the fasteners. E&OE © 2017 Unimac... -
Page 7: Technical Specifications
Product Dimension (L x W x H) 320 x 125 x 320mm Product Weight 3.5kg Fasteners are standard and can be purchased at hardware Note stores In the Box CB700 Coil Nailer Carry Case Safety Goggles Oil Lubrication in bottle Allen Key E&OE © 2017 Unimac... -
Page 8: Operating Instructions
Disconnect the tool from the air supply before performing maintenance, clearing a jammed fastener, leaving the work area, moving the tool to another location or handing the tool to another person. E&OE © 2017 Unimac... -
Page 9: Preparing The Tool
6. Adjust the directional EXHAUST deflector (see Fig. 18), so that the exhaust air blast will be directed away from the operator. Grasp the deflector and rotate it to the desired position for the current application. E&OE © 2017 Unimac... -
Page 10: Using The Tool
Clean and inspect the tool daily. Carefully check for proper operation of trigger and safety mechanism. Do not use the tool unless both the trigger and the safety mechanism are functional, or if the tool is leaking air or if it needs any other repair. E&OE © 2017 Unimac... -
Page 11: Clearing A Jammed Fastener
3. Use a slender, soft steel rod to drive the drive blade to its uppermost position. Use the needle nose pliers to remove the jammed fastener (Fig. 21). 4. Follow the instructions in Preparing the Tool to reload fasteners. E&OE © 2017 Unimac... -
Page 12: Maintenance
Some user serviceable components are described in the Troubleshooting section. All repairs made by local agencies are fully guaranteed against defective material and workmanship. We cannot guarantee repairs made or attempted by anyone other than these agencies. E&OE © 2017 Unimac... -
Page 13: Troubleshooting
Wrong size fasteners. length to make the directional arrow on the nail housing tail point to the correct direction. Small piston bumper is worn and damaged. Stop using the tool. E&OE © 2017 Unimac... - Page 14 Inner diameter of the hose is too small Fasteners are jammed Fasteners are of the wrong size. Use recommended fasteners. Weld wires in the nail coil are Stop using the tool. broken. E&OE © 2017 Unimac...
-
Page 15: Exploded Parts Drawing
Pneumatic Air Coil Nailer Exploded Parts Drawing E&OE © 2017 Unimac... -
Page 16: Parts List
O-ring 24.3 x 2.8 Spring pin Spring Safe bracket guider Bumper Valve Guide Cover Trigger Valve Seat Lock washer 28 Spring Feed Hook Trigger Valve Stem Washer O-ring 20.3 x 2.5 Screw O-ring 20.3 x 1.5 Upper Nail Housing E&OE © 2017 Unimac... - Page 17 Spring Pin 2.5 x 17 Adjuster Bushing Adjuster Plate Trigger Adjuster nut Trigger Spring Spring pin O-ring 46 x 1.3 Soft Grip Sleeve O-ring 8.3 x 1.8 End cap Nose O-ring 65.4 x 2.5 Cover Air plug Washer E&OE © 2017 Unimac...
- Page 18 ©2017 Unimac. All rights reserved. No part of this document, including descriptive content, concepts, ideas, diagrams or images may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, scanning or recording, or any information storage and retrieval system, without express permission or consent from the publisher.
Need help?
Do you have a question about the CB700 and is the answer not in the manual?
Questions and answers