Table of Contents
Related Manuals for Dorma CD 80
Summary of Contents for Dorma CD 80
- Page 1 DORMA CD 80 Swing Door Operator CD 80 SWING DOOR OPERATOR INSTALLATION INSTRUCTIONS Distributed by: DORMA AUTOMATICS, Inc. 924 Sherwood Drive Toll-Free: 877-367-6211 DL2862-010 Lake Bluff, IL 60044 Fax: 877-423-7999 Jan. 2007 E-mail: automatics@dorma-usa.com Subject to change without notice...
- Page 2 DORMA DORMA CD 80 Swing Door Operator DORMA AUTOMATICS, Inc. 924 Sherwood Drive Toll-Free: 877-367-6211 DL2862-010 Lake Bluff, IL 60044 Fax: 877-423-7999 Jan. 2007 E-mail: automatics@dorma-usa.com Subject to change without notice...
- Page 3 DORMA CD 80 Swing Door Operator 1-2 mm DORMA AUTOMATICS, Inc. 924 Sherwood Drive Toll-Free: 877-367-6211 DL2862-010 Lake Bluff, IL 60044 Fax: 877-423-7999 Jan. 2007 E-mail: automatics@dorma-usa.com Subject to change without notice...
- Page 4 DORMA CD80 Swing Door Operator DORMA AUTOMATICS, Inc. 924 Sherwood Drive Toll-Free: 877-367-6211 DL2862-010 Lake Bluff, IL 60044 Fax: 877-423-7999 -2007 E-mail: automatics@dorma-usa.com Subject to change without notice...
- Page 5 DORMA CD 80 Swing Door Operator min. 15° 90° DORMA AUTOMATICS, Inc. 924 Sherwood Drive Toll-Free: 877-367-6211 DL2862-010 Lake Bluff, IL 60044 Fax: 877-423-7999 Jan. 2007 E-mail: automatics@dorma-usa.com Subject to change without notice...
- Page 6 DORMA CD 80 Swing Door Operator 90° DORMA AUTOMATICS, Inc. 924 Sherwood Drive Toll-Free: 877-367-6211 DL2862-010 Lake Bluff, IL 60044 Fax: 877-423-7999 Jan. 2007 E-mail: automatics@dorma-usa.com Subject to change without notice...
- Page 7 Standard funtion programs and special functions very comfortable. Where a standard arm is to be installed, DORMA Functions cia programs switch OFF recommends use of an appropriate activator rather than the Automatic Push&Go function.
- Page 8 Adjusting the hydraulic settings The CD 80 exhibits di erent operating Unscrew the drive unit from the mounting plate. characteristics when used as a door closer (without electronic control) or as an AUTOMATIC operator.
- Page 9 Only set/adjust this closing range once the learning cycle has been completed. The control unit of the CD 80 is now set to the values indicated in the table. Connect the electrical wiring in accordance with the terminal connection plan.
- Page 10 DORMA CD 80 Swing Door Operator 4. Commissioning/5. Adjustment Example: 4. Commissioning (continue) LED 1 (green) ashes once - Open the door manually to the required full opening - the opening time parameter is activated angle and hold the door in this position.
- Page 11 DORMA CD 80 Swing Door Operator 5. Adjustment 6. Functional testing deactic Check the functions of the operating and control Sensortest-Pegel low activ elements while consulting the high activ "8. Operating instruction manual” LED 2 error codes (red) Sensortest-Sensor If a fault or error has occurred, this is indicated by...
- Page 12 DORMA CD 80 Swing Door Operator 7. Troubleshooting i t c 4. Commissioning/5. Adjustments/6. Functional testing section hand. s t l Remedy The door does not respond. No mains power Switch on main power switch. Plug connections not properly inserted.
- Page 13 The door may be held at an opening angle of the 8.3 Program switch extended hold-open function e.g. for the purpose The CD 80 can be equipped either with an of room ventilation. internal or an external program switch. Where an For either 5 or 10 minutes.
- Page 14 DORMA CD 80 Swing Door Operator 8. Operating instructions Deactivating the function in preset backcheck angle. extended hold-open the PERMANENT OPEN mode. · Press the pushbutton for the extended hold-open 8.9 Emergency pushbutton function once. Press the emergency o pushbutton: ·...
- Page 15 DORMA CD 80 Swing Door Operator CD 80 mit Sensor AIR 16 wiring (Reglomat) Sensor Radar + 24 VDC + 24 VDC Stop Switch as opening activator Start + 24 VDC + 24 VDC Stop Start Safety sensor Safety sensor...
Need help?
Do you have a question about the CD 80 and is the answer not in the manual?
Questions and answers