Table of Contents
Advertisement
Quick Links
®
®
®
icXchange
icXchange
icXchange
Unified IP Networking Solution
Unified IP Networking Solution
Unified IP Networking Solution
ICC 11ac Gigabit Wireless Access Point Web Manual
ICC 11ac Gigabit Wireless Access Point Web Manual
ICC 11ac Gigabit Wireless Access Point Web Manual
Product Model: ICX400GAP
Product Model: ICX400GAP
Product Model: ICX400GAP
Description: IEEE802.11ac 2x2:2 MIMO Gigabit standalone or controller-
Description: IEEE802.11ac 2x2:2 MIMO Gigabit standalone or controller-
Description: IEEE802.11ac 2x2:2 MIMO Gigabit standalone or controller-
based managed access point
based managed access point
based managed access point
Product Model: ICX420GAP
Product Model: ICX420GAP
Product Model: ICX420GAP
Description: IEEE802.11ac 3x3:3 MIMO Gigabit standalone or controller-
Description: IEEE802.11ac 3x3:3 MIMO Gigabit standalone or controller-
Description: IEEE802.11ac 3x3:3 MIMO Gigabit standalone or controller-
based managed access point
based managed access point
based managed access point
© 2015 Copyright. All Rights Reserved. International Communications Corporation, Inc
© 2015 Copyright. All Rights Reserved. International Communications Corporation, Inc
© 2015 Copyright. All Rights Reserved. International Communications Corporation, Inc
.
.
.
.
.
.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ICC ICX400GAP
Summary of Contents for ICC ICX400GAP
- Page 1 Unified IP Networking Solution Unified IP Networking Solution Unified IP Networking Solution ICC 11ac Gigabit Wireless Access Point Web Manual ICC 11ac Gigabit Wireless Access Point Web Manual ICC 11ac Gigabit Wireless Access Point Web Manual Product Model: ICX400GAP...
-
Page 2: Intended Audience
(IP) technologies is assumed. Documentation ® The ICC icXchange product and support documentation consists of a variety of manuals, installation guides, videos, knowledge articles, sample designs, troubleshooting, and FAQ guides to assist you with the deployment of your new and innovative solution. -
Page 3: Table Of Contents
ICX420GAP Manual Contents Chapter1: Product Introduction....................5 Product Overview......................5 2 Installing the ICX420GAP Series AP ................8 Login Web Network Management..................12 Quit Web Network Management..................12 ® Introduction to the icXchange Web Management Page Layout ........13 ® Introduction to icXchange Web Network Management Function Definitions....15 Introduction to Web Page Common Controls ..............16 ®... - Page 4 ICX420GAP Manual Modify Virtual Access Point settings ................30 AP Security Configuration: No Security ..............31 Static WEP Security Configuration................31 WPA Personal Security Configuration................32 WPA Enterprise Security Configuration..............33 AP Mode.........................33 Wireless Distribution System (WDS)................34 Chapter 5: Services ......................39 Web Server ........................39 NTP ..........................40 Chapter 6: Maintenance ....................41 Configuration........................41 Upgrading AP Firmware ....................43...
-
Page 5: Chapter1: Product Introduction
Product Overview Product Overview The ICC ICX400 Series is made up of the ICX400GAP, 2x2 MIMO, and ICX420GAP, 3x3 The ICC ICX400 Series is made up of the ICX400GAP, 2x2 MIMO, and ICX420GAP, 3x3 The ICC ICX400 Series is made up of the ICX400GAP, 2x2 MIMO, and ICX420GAP, 3x3 MIMO, which are 802.11ac high performance access points that not only ensure... - Page 6 ICX420GAP Manual ICX420GAP Manual ICX420GAP Manual The below figure describes key attributes of the ICX420GAP. The below figure describes key attributes of the ICX420GAP. The below figure describes key attributes of the ICX420GAP. Rear Rear Rear USB Port USB Port USB Port Kensington Kensington...
- Page 7 ICX420GAP Manual ICX420GAP Manual ICX420GAP Manual Front Front Front Power Power Power LAN 1 LAN 1 LAN 1 LAN2 LAN2 LAN2 2.4GHz 2.4GHz 2.4GHz 5GHz 5GHz 5GHz...
-
Page 8: Installing The Icx420Gap Series Ap
ICX420GAP Manual 2 Installing the ICX420GAP Series AP ICX420GAP Series can be installed indoor using one of two methods: Wall hanging installation T-keel installation Wall Installation To mount the Access Point on the wall, use the supporting expansion screw tubes and screws for wall mounting. - Page 9 ICX420GAP Manual Punch and nail on the wall Stuck the AP on the screws Complete the installation Ceiling or T-keel Installation 1. The T-keel will support a width between 12mm to 30mm (.5 to 1.1 inches) 2. This installation method applies to the T-keel a n d no other kinds of keels. The T-keel mounting kit includes two plastic mounting kits and two fixed screws, included in the accessory bag.
- Page 10 ICX420GAP Manual Step 1: Choose the right mounting kit according to the width of the T-keel and use the two fixing screws to fix the mounting kit on the AP as below: Step 2: Close the mounting kit of the AP to the T-keel as below: Step 3: Turn the AP counterclockwise to close to the T-keel and make the two diagonal slots of the mounting kit latch to the T-keel.
- Page 11 ICX420GAP Manual Connecting AP Power ICX420GAP series indoor AP supports local power or power via a PoE device. Users can choose the method according to the actual network environment. Validation check before powering on the AP After installing the AP , the user should check the device before powering on for the first time: ...
-
Page 12: Login Web Network Management
ICX420GAP Manual Login Web Network Management The default Web login process and details are identified below. While the steps are simple, a user must understand how networks operate, the use of IP addresses, and general networking theory. Default Web login information: User name: admin Password: admin IP address of the device: 192.168.1.10... -
Page 13: Introduction To The Icxchange ® Web Management
ICX420GAP Manual ® Introduction to the icXchange Web Management Page Layout The Web network management page includes: navigation bar, configuration area, and help area shown as fig 1.2. Fig 1.2 initial page of Web network management Fig: 1.2 Navigation Bar The Navigation Bar is the central management and navigation location tree from which to ®... - Page 14 ICX420GAP Manual Configuration area: This visual area typically in white is to the right of the Navigation bar and provides visual representation and confirmation of any changes in status made during any management configuration session as shown in fig 1-3 Fig.
-
Page 15: Introduction To Icxchange ® Web Network Management Function Definitions
ICX420GAP Manual ® Introduction to icXchange Web Network Management Function Definitions ® The following Table 1-1 provides a simplified quick view of the icXchange management features: Table 1-1 Menu/label Function explanation Show the AP address (IP address and MAC address), version (firmware version) and device Basic settings information. -
Page 16: Introduction To Web Page Common Controls
ICX420GAP Manual Services Configure the http server status, http server port, Web server maximum number of users and timeout of page. Configure the NTP server status, NTP server ip address and NTP updating interval. Set the configuration to restart the AP and restore it Configuration Maintenance to factory configuration. - Page 17 ICX420GAP Manual browser after first logging into the device through the web network management.
-
Page 18: Chapter 2: Basic Configuration
ICX420GAP Manual Chapter 2: Basic Configuration When viewing the basic configuration ‘Description’ of the access point, the following information will display: 1. Review description of this access point 2. Device information 3. Administrator password 4. System settings... -
Page 19: Detailed Explanation Of Settings
ICX420GAP Manual Detailed Explanation of settings Description of this Access Point IP Address Shows the IP address of the current device. IPv6 Address Shows the IPv6 address of the current device. IPv6 Auto configured Global Addresses Shows the IPv6 auto configured global address of the current device. -
Page 20: Device Information
ICX420GAP Manual Device Information Product identifier Shows the product ID of the current device. Hardware version Shows the hardware version of the current device. Serial number Shows the serial number of the current device. Device name Shows the device name of the current device. -
Page 21: Chapter 3: Current Status
ICX420GAP Manual Chapter 3: Current Status A review of the current status will show information including network information, statistics of sending and receiving IP packets, and the associated terminal. Interface Wired Settings MAC address Shows the MAC address of the current device. Management VLAN ID Shows the VLAN ID of the current device. -
Page 22: Wireless Settings
ICX420GAP Manual IP address Shows the IP address of the current device. Subnet mask Shows the subnet mask of the current device. IPv6 Address Shows the IPv6 address of the current device. Static IPv6 Address Prefix Shows the prefix length of static IPv6 address. Length IPv6 Auto configured Global Shows the IPv6 auto configured global addresses of the... -
Page 23: Transmit/Receive Packets
ICX420GAP Manual address. Vlan ID The VLAN can be used to create multiple internal and customer networks on the same AP. VLAN ID is configured in VAP label. Network name (ssid) Wireless network name. It is also named as SSID which is used to mark the WLAN. -
Page 24: Client Associations
ICX420GAP Manual Client Associations The client associations is shown below: Network The SSID of the client associated network. Station The MAC address of the associated client. Status Authenticated The status of authenticated means the IEEE 802.11 authentication status. Associated The status of associated means the IEEE 802.11 association status. -
Page 25: Chapter 4: Advanced Configuration
ICX420GAP Manual Chapter 4: Advanced Configuration The advanced configuration section includes wired configuration, wireless configuration, and configuration of RF parameters, virtual AP, and AP modes. Ethernet Settings... - Page 26 ICX420GAP Manual Below is a description of the advanced configuration items. Host name The host name of the AP. MAC Address The MAC address of the Ethernet interface of AP. Management VLAN ID The management VLAN is used to access the VLAN which is associated with the IP address of AP.
-
Page 27: Modify Wireless Settings
ICX420GAP Manual Modify wireless settings Country Choose the country where the AP resides. Radio interface Identify the RF device as enabled or disabled. MAC address The MAC address of the RF interface. Mode The Physical Layer standard the radio uses. Channel Choose the channel to be used by the RF device. -
Page 28: Modify Radio Settings
ICX420GAP Manual ICX420GAP Manual ICX420GAP Manual Modify radio settings Modify radio settings Modify radio settings... - Page 29 ICX420GAP Manual Below is a listing of the description of the fields on the Radio display. Radio Choose the configured RF. Status Enable/disable the RF. Mode The PHY standard used by RF. Channel Choose the channel. Channel bandwidth The channel bandwidth of 802.11n mode. Primary channel The mode of the primary channel (only the 802.11n mode is supported)
-
Page 30: Modify Virtual Access Point Settings
ICX420GAP Manual Modify Virtual Access Point settings Below is a listing of the description of the fields on the VAP display. Radio Choose the configured RF. Show the ID number of the virtual AP. Enabled Configure the status of the virtual AP. VLAN ID Configure the VLAN that the client associated with the... -
Page 31: Ap Security Configuration: No Security
ICX420GAP Manual virtual AP belongs to. SSID Configure the name of the wireless network. Broadcast SSID Configure whether to broadcast the SSID. Security Configure the security mode. AP Security Configuration: No Security The AP can be configured to have no security setting. While not recommended, IT administrators can choose to set the security configuration as None, effectively turning off all security features of the AP. -
Page 32: Wpa Personal Security Configuration
ICX420GAP Manual Transfer key index Configure the key index. Key length Configure the length of key. Key type Configure the type of key. Wep keys Configure the key of 1-4. Authentication Configure the authentication mode. WPA Personal Security Configuration Choose the security configuration as WPA Personal to show the detailed configuration information of the WPA Personal security configuration. -
Page 33: Wpa Enterprise Security Configuration
ICX420GAP Manual WPA Enterprise Security Configuration Select security configuration WPA Enterprise for more advanced security options. Using the drop down box to select WPA Enterprise will display configuration fields and detailed configuration information of the WPA Enterprise security configuration. The previously entered user name and password from the radius server should be input in the client to pass the authentication. -
Page 34: Wireless Distribution System (Wds)
ICX420GAP Manual connected to it. Management AP Configure the AP modes. administrative mode Switch IP address of 1-4 Configure the IP address of AC under the fit AP mode. Switch IPv6 address of 1-4 Configure the IPv6 address of AC under the fit AP mode. - Page 35 AP that is being connected to bridge the traffic over from its clients is called a Satellite WDS in FAT mode WDS in FAT mode WDS in FAT mode Topology: Topology: Topology: ICX400GAP or ICX420GAP ICX400GAP or ICX420GAP ICX400GAP or ICX420GAP ICX400GAP or ICX420GAP ICX400GAP or ICX420GAP ICX400GAP or ICX420GAP Root AP configuration through the CLI...
- Page 36 ICX420GAP Manual ICX420GAP Manual ICX420GAP Manual Satellite AP configuration through CLI Satellite AP configuration through CLI Satellite AP configuration through CLI Telnet the AP which needs to be selected as Satellite and enter the following Telnet the AP which needs to be selected as Satellite and enter the following Telnet the AP which needs to be selected as Satellite and enter the following commands: commands:...
- Page 37 ICX420GAP Manual ICX420GAP Manual ICX420GAP Manual Satellite AP configuration: Satellite AP configuration: Satellite AP configuration: 1. On the AP that is chosen as a satellite AP go to the web interface of the AP and 1. On the AP that is chosen as a satellite AP go to the web interface of the AP and 1.
- Page 38 ICX420GAP Manual ICX420GAP Manual ICX420GAP Manual Verification: Verification: Verification: Telnet the APs and verify the status of WDS by using the following commands. Telnet the APs and verify the status of WDS by using the following commands. Telnet the APs and verify the status of WDS by using the following commands. ICX420GAP#get wds wds0 ICX420GAP#get wds wds0 ICX420GAP#get wds wds0...
-
Page 39: Chapter 5: Services
ICX420GAP Manual Chapter 5: Services Services include web server and NTP server configuration. Web Server HTTP Server Status Configure the HTTP server status. Disable means not to provide the HTTP service; the web page of AP cannot be accessed in. HTTP Port Configure the port number of the HTTP server. -
Page 40: Ntp
ICX420GAP Manual CurrentTime Configure the current time. Status Configure the NTP server status. Disable means not to enable the NTP server. Server Address Configure the IP address of NTP server. Interval Configure the interval of the synchronization. -
Page 41: Chapter 6: Maintenance
ICX420GAP Manual Chapter 6: Maintenance The system maintenance includes configuration management and the firmware upgrade process. Configuration Click Reset to restore the configuration of the AP to default settings. The default working mode of AP is FIT AP mode. Choose the download method as HTTP mode, click Download and confirm it. The current configuration files of AP will be downloaded through HTTP. - Page 42 ICX420GAP Manual confirm it. The configuration file will be downloaded to the appointed TFTP server and the file name is the input name. When the upload method is chosen as HTTP mode, click Browse to choose the configuration file (the format is *.xml) which needs to be uploaded. Confirm it and click Restore.
-
Page 43: Upgrading Ap Firmware
ICX420GAP Manual Upgrading AP Firmware The access point firmware upgrade process can be completed via HTTP or TFTP. When using either process the steps are simple, quick, and can be used by any IT administrator. Firmware Upgrade section and definition: Item Description Firmware Version... - Page 44 ICX420GAP Manual firmware file. After clicking Firmware Upgrade, there will be a secondary window describing the upgrade progress. 4. Click Confirm to confirm the upgrade and start the upgrading process. NOTE By clicking “Upgrade” and “Confirmation,” the upgrade process will start.
- Page 45 ICX420GAP Manual 3. Input the IP address of the TFTP server. 4. Click Upgrade. After selecting Upgrade, there will be a window which describes the upgrading process. 5. Click Confirm which will start the final upgrade process. NOTE By confirming the upgrade process as well as approving the secondary confirmation, the upgrade process will start.
-
Page 46: Regulatory And Compliance
ICC’s warranty and all applicable regulatory certifications and approvals. Only antennas specified for your region by ICC can be used with this product. The use of external amplifiers or non-ICC antennas may invalidate regulatory certifications and approvals. -
Page 47: Usa - Radio Frequency Requirements
ICX420GAP Manual This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. USA —... -
Page 48: Usa - Federal Communications Commission (Fcc) Emc Compliance
Commission helpful: The Interference Handbook. This booklet is available from the US Government Printing Office, Washington, DC 20402. Stock No. 004-000-0034504. ICC is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this ICC Wireless 11b/g PoE Access Point, ®... -
Page 49: Manufacturer's Fcc Declaration Of Conformity
ICX420GAP Manual ICX420GAP Manual ICX420GAP Manual Manufacturer’s FCC declaration of conformity Manufacturer’s FCC declaration of conformity Manufacturer’s FCC declaration of conformity Model Number: ICX420GAP International Communications Corporation Model Number: ICX420GAP International Communications Corporation Model Number: ICX420GAP International Communications Corporation Equipment Type: WLAN Access Point Equipment Type: WLAN Access Point Equipment Type: WLAN Access Point Complies with Part 15 of the FCC rules. -
Page 50: Industry Canada - Emissions Compliance Statement
ICX420GAP Manual Pour empecher que cet appareil cause du brouillage au service faisant l’objet d’une licence, il doit etre utilize a l’interieur et devrait etre place loin des fenetres afin de Fournier un ecram de blindage maximal. Si le matriel (ou son antenne d’emission) est installe a l’exterieur, il doit faire l’objet d’une licence. -
Page 51: Warranty
IcXchange Service Contract. ICC warrants that for a period of two (2) years from the invoice date on the authorized ICC distributor’s invoice that the Software supplied by ICC will perform substantially in ®... - Page 52 UNINTERRUPTED OR ERROR FREE. ICC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS. ICC SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND...
- Page 53 Test results and examples are subject to unique business conditions, client IT environment, ICC products deployed, and other factors. These results may not be typical; your conditions, client IT environment, ICC products deployed, and other factors. These results may not be typical; your conditions, client IT environment, ICC products deployed, and other factors.
Need help?
Do you have a question about the ICX400GAP and is the answer not in the manual?
Questions and answers