Table of Contents
Advertisement
Quick Links
THANK YOU!
We are grateful for your purchase of HYT product. We believe this easy–to-use
radio will provide you with dependable and reliable communications. This HYT
portable two-way radio is a precision device. Treat it with care, and you will enjoy
years of reliable operation.
MODELS COVERED IN THIS MANUAL
TC3000 VHF Radio
TC3000 UHF Radio
1
Advertisement
Table of Contents
Related Manuals for HYT TC3000
Summary of Contents for HYT TC3000
- Page 1 THANK YOU! We are grateful for your purchase of HYT product. We believe this easy–to-use radio will provide you with dependable and reliable communications. This HYT portable two-way radio is a precision device. Treat it with care, and you will enjoy years of reliable operation.
-
Page 2: Table Of Contents
Contents User Safety, Training, and General Information Compliance with RF Energy Exposure Standards Important Note: FCC Information FCC Compliance Precautions Product Inspection Battery Information Accessory Installation Battery Antenna Belt Clip Earplug Cover External Earphone/Microphone (optional) Getting Started Features and Operation Turn on/off the radio Adjust the Volume Select Channel... -
Page 3: User Safety, Training, And General Information
BEFORE USING YOUR HYT PORTABLE TWO-WAY RADIO. Compliance with RF Energy Exposure Standards Your HYT two-way radio is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to radio frequency electromagnetic energy. - Page 4 Use only HYT approved, supplied batteries or HYT approved replacement batteries. Use of non- HYT -approved batteries may exceed FCC RF exposure guidelines. Approved Accessories For a list of HYT approved accessories, see the accessories page of this user manual or visit the following website which lists approved accessories: http://www.hty.com.cn...
-
Page 5: Important Note: Fcc Information
Important note: FCC Information FCC Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. -
Page 6: Precautions
FCC Requirements Your radio must be properly licensed Federal Communications Commission prior to use. Your HYT Wireless dealer can assist you in meeting these requirements. Your dealer will program each radio with your authorized frequencies, signaling codes, etc., and will be there to meet your communications needs as your system expands. -
Page 7: Product Inspection
Product Inspection Thank you for your use of HYT portable two-way radio TC3000. Before use, you are recommended to inspect the product as follows. First check the shipping carton for any signs of damage. If any damage has occurred, please contact your dealer immediately. -
Page 8: Battery Information
When the battery power is low, it needs to be charged. Applicable Battery Packs Charge only the HYT approved battery packs. Other batteries may burst and cause personal injury. Safety attention 1. - Page 9 When radio LED flashes red and three Beeps sound every 30 seconds after the battery is installed, that means battery power is low. Please charge the battery. You are recommended to use HYT-approved, supplied charger; Charger LED will indicate the charging status.
-
Page 10: Accessory Installation
Accessory Installation Battery Attach the battery Insert the two tabs on bottom of the battery into the slots at the bottom of the radio. Push top of the battery towards the radio until a click is heard. (See figure 1) Fig.1 Remove the battery Turn off the radio. -
Page 11: Belt Clip
Install Remove Belt Clip Attach Belt Clip Align the slot of the belt clip with the T-slot at the battery cover and press the belt clip downwards until it is locked. (See figure 3) Fig.3 Remove the belt clip Press the disassembly release upwards with a key until it releases and then push the belt clip upwards with your thumb to remove it. -
Page 12: Earplug Cover
Earplug Cover Rotate the screw at the bottom of the cover counter clockwise by a screwdriver until it is out of the nut to remove the Earphone/Microphone jack cover. (See figure 5) Fig.5 External Earphone/Microphone (Optional) Insert the tab at the bottom of the earphone/microphone into the slot on top of the radio. (See figure 6). -
Page 13: Getting Started
Getting Started (1) Antenna Used to transmit/receive signals. (2) LED Following table indicates LED indication and corresponding radio status. Status No display Standby Green Receive Transmit Flashing green Scan Flashing red Low battery voltage Flashing orange Call waiting (3) Channel Selector Used to select wanted channel. - Page 14 (8) Microphone Used to input sounds. (9) External Jack Used to connect with external earphone or programming cable. (10) Belt Clip Used to clip the radio on your belt. (11) Battery Pack (12) PTT key Press and hold PTT, radio operates in transmit mode. Release PTT, radio returns to receive mode.
-
Page 15: Features And Operation
Features and Operation Note: TC3000 provides a series of audible alert tones. A series of tones may be sounded with the following conditions: Bourdon Operation Description Audible Tone Turn on the radio Power on-Ready Turn on the radio Power on-Failure... -
Page 16: Selectable Power
3. Press PTT and speak into the microphone with your mouth 2.5-5 centimeters away from the radio. LED glows red during transmission. 4. Release PTT key to finish speaking. Receive Turn on the radio. 2. Rotate “Channel Selector” knob to select wanted channel. 3. -
Page 17: Scan
Scan Scan feature allows you to monitor all channels. When scan feature is enabled, the radio will detect all channels. If an active channel is detected, the radio will remain on that channel and you will be able to hear the conversation. -
Page 18: Built-In Modem
1. VOX feature enables you to transmit automatically by speaking into the microphone. 2. Transmission stops automatically when you stop speaking. 3. Press PTT to disable VOX feature. 4. Turn the radio on again, VOX feature will be activated. Built-in Modem MSK modulator with speed of 1200/2400bit/s inside the radio supports data transmission. - Page 19 Group Call: A call generated by an individual radio to a radio group. Broadcast: A unidirectional call generated by an individual radio to a whole system. You need to do some settings via programming software to use HDC1200. Select HCD1200 in “Optional Signalling" box in channel edit window. And select corresponding call list for CALL1 and CALL2.
-
Page 20: Troubleshooting Guide
Troubleshooting Guide Trouble Solution Battery may be used up. Please replace or recharge the battery. No power Battery may not be attached properly. Remove the battery and attach again. Power doesn’t last long even if fully Battery life cycle is over. Please replace it with a charged. -
Page 21: Optional Accessories
Optional Accessories Dual Pocket Rapid Charger CH20L01 Multi-unit Charger MCL01 (for Li-Ion batteries) (for Li-Ion batteries) Remote Speaker Receive-only Earpiece with Transparent Microphone SM08N1 Acoustic Tube (use with Remote Speaker Microphone SM08) ESS04 Receive-only Earpiece (for use with Remote Switch Power (exclusive to dual Speaker Microphone SM08) ESS01 pocket rapid charger) PS2001 Earbud with Transparent... - Page 22 Throat-vibrating Earpiece with Headset ECN02 Transparent Acoustic Tube ELN01 Leather Carry Case (applicable Transparent Waterproof （适用于 TC3000 系列） to TC3000 series) LCBN09 Bag LCBY03 Chest Pack LCBN03...
-
Page 23: Frequency Chart
HYT endeavor to achieve the accuracy and completeness of this manual, but cannot guarantee its accuracy at all times. All the above specifications and design are subject to change by HYT without notice. All the reproduction and translation of this manual without authorization of HYT is not allowed.