ACL CSC400 Installation And Operation Manual page 29

2.1.14
2.1.15
2.1.16
2.1.17
2.1.18
2.1.19
2.1.20
2.1.21
2.1.22
2.1.23
2.1.24
2.1.25
2.1.26
2.1.27
2.1.28
2.1.29
2.1.30
2.2 Line Display
Config
2.3 Temp Setpoints
2.4 Show Last IGN
SD
2.5 TMain 1 On
Time View
2.6 TMain 2 On
Time View
Dual TC1&2 SD No
4-20 Out Settings
4-20 In 1 Settings
4-20 In 2 Settings
Purge Cycle 10s
IGN Int-Purge 0s
AUX1 Relay Settings
AUX2 Relay Settings
PWR Save Disabled
PWR Fail Latched
High Temp Latched
Hi Tmp TC3 Latched
High Gas Latched
Low Gas Latched
Level Latched
Aux 1 Latched
Aux 2 Latched
Line 1: TC1 temp w setpoint
Line 2: TC2 temp w setpoint
Line 3: FI mode VLVs 1
TC1 IGN1 Set 200°C
TC1 IGN2 Set 300°C
TC2 Set 600°C
TC3 Set 400°C
Low Temp Set 200°C
Deadband TC1 IGN1 1
Deadband TC1 IGN2 1
Deadband TC2 1
Deadband TC3 1
Years Hours
Months Minutes
Days
Reset TMain 1 Timers
Years Hours
Months Minutes
Both Ignitors must be enabled for this option to
have an effect on the Alarm/Status contacts
Option Dual TC1&2 10°C Difference Shutdown Y/N
Yes: Shutdown if TC1 & 2 are different by greater
than 10°C (18°F)
No: No link between TC1 & TC2
Menu 4-20mA Output Settings Menu
Menu 4-20mA Input 1 Settings Menu (Level)
Menu 4-20mA Input 2 Settings Menu (Press.)
Option Purge Cycle Time (0s - 300s) (before first ignition
trial)
Option Extra Inter-Purge Time (0s - 240s) between
Ignitor relight trials.
Menu AUX1 Relay Settings Menu
Menu AUX2 Relay Settings Menu
Option Power Save Enable/Disable
Option Power Fail Shutdown Latched/Unlatched
Option High Temp Shutdown Latched/Unlatched
Option TC3 High Temp SD Latched/Unlatched
Option High Gas Shutdown Latched/Unlatched
Option Low Gas Shutdown Latched/Unlatched
Option Level Shutdown Latched/Unlatched
Option Auxiliary 1 Shutdown Latched/Unlatched
Option Auxiliary 2 Shutdown Latched/Unlatched
Menu Line Display Configuration - Select items to
display on the three top lines on the display
Option Select information to display for Line 1
Option Select information to display for Line 2
Option Select information to display for Line 3
Menu
Option Change TC1 Ignitor 1 Setpoint temperature
Change TC1 Ignitor 2 Setpoint temperature
Option Change TC2 Setpoint temperature
Option Change TC3 Setpoint temperature
Option Change Low Temp SD/ALM Setpoint temperature
Option
Set Deadband for TC1 IGN1: 1-5°C or 2-10°F
Option
Set Deadband for TC1 IGN2: 1-5°C or 2-10°F
Option
Set Deadband for TC2: 1-5°C or 2-10°F
Option
Set Deadband for TC3: 1-5°C or 2-10°F
Information Show the last shutdown(s) for IGN 1 / 2 and the
time and date that they occurred
Menu Display time that the TMain 1 solenoid has been
on since the last TMain timer reset
Information
Information
Information
Option Reset TMain 1 solenoid timers
Menu Display time that the TMain 2 solenoid has been
on since the last TMain timer reset
Information
Information
29