Selectable Code Override - Omega Research & Development UltiMate Owner's Manual

Executive model one vehicle security alarm system with model one remote control transmitters
Table of Contents

Advertisement

#
FEATURE
1
Selectable Coded Override
2
Last Door Arming
3
Automatic Rearming
4
Starter Interrupt Circuit
5
Automatic Starter Interrupt
6
Ignition Activated Override
7
Doors Lock With Last Door Arming
8
Doors Lock With Automatic Rearming
9
Doors Lock With Ignition
10
Ignition OFF Unlock #1
11
Ignition OFF Unlock #2
12
Open Door Bypass To Previous Three Features
13
Confirmation Chirps
14
Confirmation Chirps In Valet Mode
15
Activated Alarm Cycle
16
Lights On Upon Disarm
17
Disarm Alarm Upon Trunk Release
18
Doorlock Pulse Time
19
Double Unlock Pulse
20
Arming Delay
21
Pulsed Horn / Steady Siren Output
22
Horn Chirp Level
23
Total Closure Lock Output
24
Alarm Functions Bypass
25
Ignition-Activated Anti-Carjacking Protection
26
Door-Activated Anti-Carjacking Protection
27
Open Door Warning Upon Arming
28
PANIC Button Operates "Panic" or Additional Output
29
Transmitter-Activated Anti-Carjacking Protection
30
Doorlocking In Add-on Mode
DEFAULT
1 & 0 (see page 20)
60 Seconds (ON)
.8 second (ON)
3 Seconds (ON)
Pulsed Horn ( ON)
Level 2 (OFF)
Page - 18
Valet Switch. This programmable feature, which is explained in
detail on pages 20-21, allows you to further enhance the
effectiveness of your security system by "hardening" its resistance
OFF
to being defeated. The factory-set default for Selectable Code
OFF
Override is one press at stage 1, and NO press at stage 2; this
ON
is the most convenient and user-friendly setting. Therefore, the
following step-by-step instructions reflects first the default setting,
OFF
and then the following text continues to explain the custom-
OFF
programmed setting.
OFF
OFF
How to Disarm the System Without Using the Transmitter
ON
Step 1 - While the system in the armed condition, enter via
ON
the driver's door. Be aware that the system will activate
ON
when the door is opened, sounding the horn, flashing the
lights, and locking the doors if the door entered is closed
ON
again before disarming the system.
ON
OFF
Step 2 - Using your key, turn the ignition on. The following
step must be performed within the next 10 seconds.
ON
Step 3 - Press and release the Valet Switch equal to the
ON
number programmed for stage #1; the factory setting is
one. If the default setting of 1 and 0 presses is retained,
OFF
press and release the Valet Switch once and the system
will instantly disarm, as indicated by two horn chirps.
If stage #2 presses have been programmed, the system will not
disarm, but pause and chirp the horn before continuing to sound.
OFF
When a stage #2 entry is required, at this point the stage #2 entry
OFF
must be made within 10 seconds. If both stage's entries are correct,
OFF
the system will disarm shortly after the stage #2 entry. After a failed
attempt to achieve Selectable Code Override, the ignition switch
OFF
must be turned off, then on again before another attempt is made.
OFF
If two failed Selectable Code Override attempts are made, the
Panic (ON)
system will ignore any further presses of the Valet Switch for two
OFF
minutes. If this occurs, the system will reset to the armed state, then
sound the horn twice after 2 minutes to indicate that another attempt
OFF
Page - 11

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the UltiMate and is the answer not in the manual?

Table of Contents