Mazda BT-50 2017 Owner's Manual

Table of Contents

Quick Links

Download this manual

Thank you for choosing a Mazda. We at Mazda design and build vehicles with complete

customer satisfaction in mind.

To help ensure enjoyable and trouble-free operation of your Mazda, read this manual

carefully and follow its recommendations.

Regular servicing of your vehicle by an expert repairer helps maintain both its

roadworthiness and its resale value. A world-wide network of Authorised Mazda Repairers

can help you with their professional servicing expertise.

Their specially trained personnel are best qualified to service your Mazda vehicle properly

and exactly. Also, they are supported by a wide range of highly specialized tools and

equipment specially developed for servicing Mazda vehicles. When maintenance or service

is necessary we recommend an Authorised Mazda Repairer.

We assure you that all of us at Mazda have an ongoing interest in your motoring pleasure

and in your full satisfaction with your Mazda product.

Important Notes About This Manual

Keep this manual in the glove box as a handy reference for the safe and enjoyable use of your Mazda. Should you

resell the vehicle, leave this manual with it for the next owner.

All specifications and descriptions are accurate at the time of printing. Because improvement is a constant goal at

Mazda, we reserve the right to make changes in specifications at any time without notice and without obligation.

Please be aware that this manual applies to all models, equipment and options. As a result, you may find

some explanations for equipment not installed on your vehicle.

A Word to Mazda Owners

Mazda Motor Corporation

HIROSHIMA, JAPAN

June 2017 (Print2)

Table of Contents

Summary of Contents for Mazda BT-50 2017

Page 1 HIROSHIMA, JAPAN Important Notes About This Manual Keep this manual in the glove box as a handy reference for the safe and enjoyable use of your Mazda. Should you resell the vehicle, leave this manual with it for the next owner.
Page 2 MEMO...
Page 3: Table Of Contents
Table Of Contents Alarm Introduction Principle of Operation ....page 45 About This Manual ......page 1 Arming the alarm ......page 47 Symbols Glossary ......page 2 Disarming the alarm ....page 47 Parts and Accessories ....page 2 Steering Wheel At a Glance Adjusting the Steering Wheel ..
Page 4 Table Of Contents Fuel Consumption ..... page 122 Air-Conditioning Principle of Operation ....page 88 Transmission Air Vents ........page 89 Manual Transmission ....page 123 Manual Air-Conditioning .... page 89 Four-Wheel Drive ...... page 123 Automatic Air-Conditioning ..page 92 Electronic Locking Heated Windows ......
Page 5 Table Of Contents Cold Weather Precautions ..page 149 Repairing Minor Paint Reduced Engine Performance ..page 150 Damage ........page 189 Driving Through Water ....page 150 Vehicle battery Vehicle Loading ......page 152 Jump-Starting the Vehicle ..page 190 Towing Battery connection points ..
Page 6 Table Of Contents Using TMC ........ page 231 Auxiliary input (AUX IN) Auxiliary input (AUX IN) Map updates socket ......... page 260 Map updates ......page 232 Audio system care Audio introduction Aerial ......... page 261 Important audio information ..page 233 Audio troubleshooting Audio unit overview Audio troubleshooting ....
Page 7: Introduction
This vehicle has received the endorsement ABOUT THIS MANUAL of TÜV, the accredited international testing organisation, for its allergy- Thank you for choosing Mazda. We friendly properties. recommend that you take some time to get All materials used in the manufacture of...
Page 8: Symbols Glossary
Genuine Mazda parts and accessories WARNING have been designed specifically for your vehicle. Unless we have specifically stated, we have not tested non-Mazda You risk death or serious injury to parts and accessories and, therefore, we yourself and others if you do not...
Page 9: At A Glance
At a Glance AT A GLANCE Instrument panel overview - Right-hand drive The equipment and installation position varies by vehicle...
Page 10 At a Glance Instrument panel overview - Left-hand drive J K N P V U O Q R The equipment and installation position varies by vehicle Door lock button. See Locking and Unlocking (page 38). Audio unit. See Audio unit overview (page 235). Multi-functional display.
Page 11 At a Glance Air-conditionings. See Manual Air-Conditioning (page 89), See Automatic Air-Conditioning (page 92). Auxiliary input and USB. See Auxiliary input (AUX IN) socket (page 111). See USB port (page 260). Hazard warning flasher switch. See Hazard Warning Flashers (page 58). Electronic Locking Differential (ELD) button.
Page 12 At a Glance Recommended settings for heating See Adjusting the Steering Wheel (page Select the outside air. 48). Close the centre air vents and open the side air vents. qManual air-conditioning Direct the side air vents toward the side Recommended settings for cooling windows.
Page 13 At a Glance qAirbag Recommended settings for heating Select the outside air. Set the temperature to 22 °C (72 °F). WARNING Open the centre and side air vents. Direct the centre air vents upwards and To avoid the risk of death or serious the side air vents toward the side injury, never use a rearward facing windows.
Page 14 At a Glance qManual transmission Selecting reverse gear - 6 speed Insert the fuel pipe nozzle up to the first notch on the nozzle, and keep it in position on the fuel filler opening. WARNING We recommend that you wait at least 10 seconds before removing the fuel nozzle to allow any residual fuel to drain into the fuel tank.
Page 15: Child Safety
Child Safety CHILD RESTRAINT PRECAUTIONS Mazda strongly urges the use of child-restraint systems for children small enough to use them. Mazda recommends use of a Mazda genuine child-restraint system or one that complies with the UNECE 44 regulation. If you would like to purchase a Mazda genuine child- restraint system, please contact an Authorised Mazda Repairer.
Page 16 Child Safety WARNING Use the correct size child-restraint system: For effective protection in vehicle accidents and sudden stops, a child must be properly restrained using a seat belt or child-restraint system depending on age and size. If not, the child could be seriously injured or even killed in an accident. Follow the manufacturer's instructions and always keep the child-restraint system buckled down: An unsecured child-restraint system is dangerous.
Page 17 Child Safety WARNING Extreme Hazard! Never use a rear-facing child-restraint system on the front passenger seat with an air bag that could deploy: Extreme Hazard! Do not use a rearward facing child restraint on a seat protected by an airbag in front of it! Even in a moderate collision, the child-restraint system can be hit by a deploying air bag and moved violently backward resulting in serious injury or death to the child.
Page 18 Child Safety WARNING Do not install a front-facing child-restraint system on the front passenger seat unless it is unavoidable: In a collision, the force of a deploying air bag could cause serious injury or death to the child. If installing a front-facing child-restraint system on the front passenger seat is unavoidable, move the front passenger seat as far back as possible and make sure that the front passenger air bag deactivation switch is in the OFF position.
Page 19 Child Safety WARNING Always attach the tether strap to the correct tether anchor position: Attaching the tether strap to the incorrect tether anchor position is dangerous. In a collision, the tether strap could come off and loosen the child-restraint system. If the child-restraint system moves it could result in death or injury to the child.
Page 20: Child Seat Positioning
Child Safety CHILD SEAT POSITIONING WARNING Please consult your Repairer for the latest details relating to Mazda recommended child seats. Extreme Hazard! Do not use a rearward facing child restraint on a seat protected by an air bag in front...
Page 21 ISOFIX baby safety seat is the Britax Roemer Baby Safe. Please consult your Repairer for the latest details relating to Mazda recommended child seats. At time of publishing the recommended Group 1 ISOFIX child seat is the Britax Roemer Safefix PLUS. Please consult your Repairer for the latest details relating to Mazda recommended child seats.
Page 22: Isofix Anchor Points
Child Safety Double cab í ISOFIX ANCHOR POINTS WARNING Use an anti-rotation device when using the ISOFIX system. We recommend that you use a top tether or a support leg. NOTE When you are purchasing an ISOFIX restraint, make sure that you know the correct mass group and ISOFIX size class for the intended seating locations.
Page 23: Booster Seats
Child Safety 3. Route the tether strap to the anchor BOOSTER SEATS point. WARNING WARNING Do not install a booster seat or a Make sure the top tether strap is not booster cushion with only the lap slack or twisted and is properly located strap of the seat belt.
Page 24 Child Safety When using a booster cushion, always Booster seat (Group 2) install the vehicle head restraint to the seat where the booster cushion is installed. We recommend that you use a booster seat that combines a cushion with a backrest instead of a booster cushion only.
Page 25: Child Safety Locks
Child Safety CHILD SAFETY LOCKS WARNING You cannot open the doors from inside if you have put the child safety locks Left-hand side Turn anti-clockwise to lock and clockwise to unlock. Right-hand side Turn clockwise to lock and anti-clockwise to unlock.
Page 26: Occupant Protection
Occupant protection Reduce the possibility of injuries to PRINCIPLE OF lower body and legs during an accident OPERATION because the air bags provide no protection to these parts of the body. qSupplementary Restraint Systems Hold the driver in a position which (SRS) Precautions allows better control of the vehicle.
Page 27 Occupant protection WARNING WARNING Children should not ride in the front Do not sit too close to the driver and passenger seat: front passenger air bags: Placing a child, 12 years or under, in Sitting too close to the driver and front the front seat is dangerous.
Page 28 Occupant protection WARNING WARNING Do not attach objects on or around the Do not attach objects on or around the area where driver and front passenger area where a curtain air bag deploys: air bags deploy: Attaching objects to the areas where Attaching an object to the driver and the curtain air bag activates such as front passenger air bag modules or...
Page 29 An expert repairer, we recommend an Do not modify the suspension: Authorised Mazda Repairer can Modifying the vehicle suspension is provide the special care needed in the dangerous. If the vehicle's height or removal and installation of front seats.
Page 30 All the seats have lap/shoulder belts. These belts have retractors with inertia Should you sell your Mazda, we urge locks that keep them out of the way when you to tell the new owner of its air not in use. The locks allow the belts to...
Page 31 Have an expert repairer, we vehicle. They could be seriously recommend an Authorised Mazda injured or even killed. In the same Repairer inspect all seat belt systems collision, occupants wearing seat belts in use during an accident before they would be much safer.
Page 32 Occupant protection WARNING WARNING Instructions for Use of Seat Belt No modifications or additions Assemblies: should be made by the user which Seat belts are designed to bear upon will either prevent the seat belt the bony structure of the body, and adjusting devices from operating to should be worn low across the front remove slack, or prevent the seat...
Page 33 Occupant protection qAirbags NOTE You will hear a loud bang and see a WARNING cloud of harmless powdery residue if an airbag deploys. This is normal. Do not modify the front of your Only wipe airbag covers with a vehicle in any way. This could damp cloth.
Page 34 Occupant protection Curtain airbags are fitted inside the trim Side airbags panels over the front and rear side windows. Moulded badges in the B-pillar trim panels indicate that curtain airbags are fitted to your vehicle. The curtain airbags will deploy during significant lateral collisions.
Page 35: Fastening The Seat Belts
Occupant protection The driver and front passenger seat belt FASTENING THE SEAT retractors are fitted with a seat belt BELTS pretensioner. Seat belt pretensioners have a lower deployment threshold than the airbags. During minor collisions, it is WARNING possible that only the seat belt pretensioners will deploy.
Page 36: Seat Belt Height Adjustment
Occupant protection Pull the belt out steadily. It may lock if SEAT BELT HEIGHT you pull it sharply or if the vehicle is on a í ADJUSTMENT slope. Press the red button on the buckle to release the belt. Let it retract completely and smoothly.
Page 37: Seat Belt Reminder
Occupant protection í SEAT BELT REMINDER USING SEAT BELTS DURING PREGNANCY WARNING The occupant protection system will only provide optimum protection when you use the seat belt properly. Type 1: The seat belt warning lamp will WARNING be illuminated for 6 seconds when the ignition is turned on to remind the driver Position the seat belt correctly for your to fasten the seatbelt.
Page 38: Disabling The Passenger Airbag
Occupant protection If the airbag warning lamp illuminates or DISABLING THE flashes when you are driving, this PASSENGER AIRBAG indicates a malfunction. Remove the child restraint and have the system checked immediately. WARNING í qDisabling the passenger airbag Make sure that the passenger airbag is disabled when using a rearward facing child restraint on the front passenger seat.
Page 39: Constant Monitoring
Occupant protection qEnabling the passenger airbag CONSTANT MONITORING The following components of the air bag WARNING systems are monitored by a diagnostic system: Make sure that the passenger airbag is Crash sensors, and diagnostic module enabled when you are not using a (SAS unit) child restraint on the front passenger seat.
Page 41: Keys And Remote Controls
Keys and Remote Controls GENERAL INFORMATION PROGRAMMING THE ON RADIO FREQUENCIES REMOTE CONTROL NOTE CAUTION Additional remote controls can be The radio frequency used by your programmed only if the vehicle is remote control can also be used by supplied with at least one remote other short distance radio control.
Page 42 Keys and Remote Controls 5. Switch the ignition back on (position 5. Insert the additional key within 10 II) or wait for ten seconds without seconds which need to be programmed. programming another remote control to end the key programming. Only the remote controls which you have just programmed are now able to lock and unlock the vehicle.
Page 43: Changing The Remote Control Battery
Keys and Remote Controls 3. Carefully remove the cover. CHANGING THE REMOTE CONTROL BATTERY Make sure that you dispose of old batteries in an environmentally friendly way. Seek advice from your local 4. Turn the remote control over to remove authority regarding recycling.
Page 44: Locks
Locks qLocking and unlocking the doors LOCKING AND with the remote control UNLOCKING Automatic relocking: The doors will relock automatically if you do not open a NOTE door within 45 seconds of unlocking the doors with the remote control. The door Do not leave your keys in the vehicle.
Page 45 Locks Reprogramming the unlocking function NOTE The unlocking function may be Double locking is activated only when reprogrammed so that only the driver's all the passenger doors are closed and door is unlocked. See Programming the the bonnet is closed in the vehicle fitted remote control (page 35).
Page 46 Locks qDriver configuration mode Press the central lock or unlock button three times within three seconds and wait for three seconds to toggle the automatic NOTE unlocking function. This operation has to be done within 30 If the automatic unlocking function is seconds.
Page 47 Locks Left-hand side Turn clockwise to lock. Right-hand side Turn anti-clockwise to lock. Unlocking NOTE If the child safety locks have also been activated, pulling the internal lever will only deactivate the emergency locking and not the child safety lock. The doors can only be opened using the external door handle.
Page 48: Engine Immobiliser
Consult an Authorised Mazda Repairer. Modification and Add-On Equipment Mazda cannot guarantee the immobilizer system's operation if the system has been modified or if any add-on equipment has been installed.
Page 49: Coded Keys
If you lose a key, you can obtain are placement from your Authorised Mazda Repairer. If possible, provide them with the key number from the tag provided with the original keys. You can also obtain additional keys from your Authorised Mazda Repairer.
Page 50: Disarming The Engine Immobiliser
Engine immobiliser DISARMING THE ENGINE IMMOBILISER The engine immobiliser is disarmed automatically when you switch the ignition on with a correctly coded key. The indicator in the instrument cluster will come on for approximately three seconds and then go out. If the indicator stays on for one minute or flashes for approximately one minute and then repeatedly at irregular intervals, your key...
Page 51: Alarm
Interior sensors NOTE To permanently deactivate the interior motion sensor, see an Authorised Mazda Repairer. Fuel fired heater may trigger false alarms. If you are using the fuel fired heater, direct the air flow towards the foot well. Alarm Horn...
Page 52 To switch this feature on or off, see an If someone opens a door or the bonnet Authorised Mazda Repairer. without a valid key or remote control. If someone removes the multi function In reduced guard, the interior sensors are display.
Page 53: Arming The Alarm
Alarm ARMING THE ALARM DISARMING THE ALARM To arm the alarm, lock the vehicle. See Disarm and silence the alarm by Locks (page 38). unlocking the doors with the key and inserting the key into the ignition switch with a correctly coded key within 12 seconds, or unlocking the doors with the remote control.
Page 54: Steering Wheel
Steering Wheel ADJUSTING THE WARNING STEERING WHEEL Make sure that you fully engage the locking lever when returning it to its WARNING original position. Never adjust the steering wheel when the vehicle is moving. NOTE Make sure that you are sitting in the correct position.
Page 55: Audio Control
Steering Wheel í AUDIO CONTROL VOICE CONTROL Volume up Seek up Volume down Seek down Voice control Mode qMode Press and hold the mode button to select the audio source. Press the mode button to: tune the radio to the next preset station Press the voice control button to select or accept an incoming telephone call deselect voice control.
Page 56: Wipers And Washers
Wipers and Washers WINDSCREEN WIPERS AUTOWIPERS CAUTION WARNING Operating this function with the engine Do not switch autowipers on in dry off will drain the battery. weather conditions. The rain sensor is very sensitive and the wipers may operate if dirt, mist or flies hit the windscreen.
Page 57: Windscreen Washers
Wipers and Washers If you switch autowipers on, the wipers WINDSCREEN WASHERS will not cycle until water is detected on the windscreen. The rain sensor will then CAUTION continuously measure the amount of water on the windscreen and adjust the speed of Operating this function with the engine the wipers automatically.
Page 58: Checking The Wiper Blades
Wipers and Washers CHECKING THE WIPER CHANGING THE BLADES WIPER BLADES qChanging the windscreen wiper blades NOTE The windscreen wiper blades are different in length. If you install wiper blades of the wrong length, the wiper blades can clash damaging the wiper system. Run the tip of your fingers over the edge of the blade to check for roughness.
Page 59 Wipers and Washers 3. Remove the wiper blade. 4. Install in the reverse order. NOTE Make sure that the wiper blade locks into place.
Page 60: Lighting
10 minutes. qEmergency stop signal Your Mazda is equipped with an emergency stop signal system that is designed to determine whether you are depressing the brake pedal with greater...
Page 61: Autolamps
Lighting AUTOLAMPS NOTE If you bring your vehicle to a WARNING complete stop while all the direction indicators are flashing rapidly, the rapid flashing of all the direction In severe weather conditions, it maybe indicators changes back to the necessary to switch your headlamps normal flashing pattern.
Page 62: Front Fog Lamps
Lighting í í FRONT FOG LAMPS REAR FOG LAMPS qControl lever WARNING WARNING Only use the rear fog lamps when visibility is restricted to less than 50 Only use the front fog lamps when metres (164 feet). visibility is considerably restricted by Do not use the rear fog lamps when fog, snow or rain.
Page 63: Headlamp Levelling
Lighting í HEADLAMP LEVELLING Without headlamp levelling With headlamp levelling You can adjust the level of the headlamp Raised headlamp beams beams according to the vehicle load. Lowered headlamp beams Set the headlamp levelling control to zero when your vehicle is unloaded. Set it to provide illumination between 35 and 100 metres (114 and 328 feet) when your vehicle is partially or fully loaded.
Page 64: Hazard Warning Flashers
Lighting DIRECTION INDICATORS HAZARD WARNING FLASHERS Right-hand side Left-hand side For item location: See At a Glance (page...
Page 65: Interior Lamps
It will go off automatically following bulb replacement procedures, after a short time to prevent the vehicle please have the bulb replaced by your battery from discharging. To switch it Authorised Mazda Repairer. back on, switch on the ignition for a short time.
Page 66 Lighting qHeadlights high and low beam qSide lamps and front direction indicators CAUTION Side lamp Do not touch the glass of the bulb. Ensure bulb is correctly seated before replacing the spring clip. Checking the bulb location through the front of the headlamp lens can be a useful aid to ensuring the bulb is correctly aligned.
Page 67 Lighting qSide direction indicator light 1. Remove the screw. 2. Remove the retainers. 3. Partially peel back the mudguard. 4. Remove the bulb. qFront fog lamps 1. Slide the lens to the rear and remove it. 2. Disconnect the electrical connector. qExterior mirror lamps NOTE You cannot separate the bulb from the...
Page 68 Lighting qRear lamps 1. Open the tailgate. 2. Remove the screws. Type 1 3. Remove the rear lamp. 4. Turn the bulb holder anti-clockwise and remove it. 5. Remove the bulb. Type 2 Direction indicator Tail and brake lamp Reversing lamp 1.
Page 69 Lighting qNumber plate lamp qInterior lamp Type 1 Freestyle and double cab 1. Carefully prise out the lamp. 2. Turn the bulb holder anti-clockwise and remove it. 3. Remove the bulb. 1. Slide the unit away from the connector and remove it. qFront map lamp 2.
Page 70 Lighting qCentre high mount stop lamp With alarm sensor Type 1 1. Carefully prise out the lamp. 2. For reading lamps, turn the bulb holder anti-clockwise and remove it. 3. Remove the bulb. 4. For centre lamp, carefully prise out the lamp lens.
Page 71 Lighting 1. Remove the cover. 2. Remove the screws. 3. Carefully prise out the lamp. 4. Disconnect the electrical connector. 5. Remove the bulb holder by turning it to 45 degree anticlockwise. 6. Remove the bulbs.
Page 72: Bulb Specification Chart
Lighting BULB SPECIFICATION CHART Bulb Specification Power (watts) Headlights high and low beam 55/60 Front direction indicator P21W Side lamp Front fog lamp Side direction indicator light Rear direction indicator WY21W Tail and brake lamp W21/5W 21/5 Reversing lamp W21W Rear fog lamp W21W Number plate lamp...
Page 73: Windows And Mirrors
Windows and Mirrors POWER WINDOWS NOTE If you operate the switches often WARNING during a short period of time, the system might become inoperable for a certain time to prevent damage due Do not operate the electric windows to overheating. unless they are free from obstruction.
Page 74 Windows and Mirrors qDriver's door switches (Regulare qSafety switch for the rear windows and Freestyle cab) A switch in the driver's door disables the rear and front passenger electric window switches. qResetting the memory of the Open electric windows Close qFront and rear passenger's door WARNING switches...
Page 75: Exterior Mirrors
Windows and Mirrors qSafety mode EXTERIOR MIRRORS WARNING WARNING The anti-trap function is not active Do not overestimate the distance of the during this procedure. objects that you see in the convex mirror. Objects seen in convex mirrors will appear smaller and further away If the system detects a malfunction, it than they actually are.
Page 76: Electric Exterior Mirrors
Windows and Mirrors The electric exterior mirrors are fitted ELECTRIC EXTERIOR with a heating element that will defrost or MIRRORS demist the mirror glass. See Heated Windows (page 96). WARNING qElectric folding mirrors Do not overestimate the distance of the objects that you see in the convex mirror.
Page 77 Windows and Mirrors INTERIOR MIRROR WARNING Do not adjust the mirror when your vehicle is moving. NOTE Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum or ammonia-based cleaning products. You can adjust the interior mirror to your preference.
Page 79: Instrument Cluster
Instrument Cluster If the needle enters the red section, the GAUGES engine is overheating. Stop the engine, switch the ignition off and determine the The equipment and installation position cause once the engine has cooled down. varies by vehicle See Engine Coolant Check (page 178). qFuel gauge The arrow adjacent to the fuel pump symbol tells you on which side of your...
Page 80: Warning Lamps And Indicators
Instrument Cluster í qABS warning lamp WARNING LAMPS AND INDICATORS The following warning lamps and indicators will come on briefly when you switch the ignition on to confirm that the system is operational: ABS warning lamp If it illuminates when you are driving, this indicates a malfunction.
Page 81 If it does not illuminate when you switch the ignition on, or begins to flash at any time, have the system checked by an expert repairer, we recommend an Authorised Mazda Repairer. If it illuminates while driving, this indicates a malfunction. Have this checked as soon as possible.
Page 82 Instrument Cluster qDynamic stability control (DSC) í indicator If the oil pressure warning lamp comes on when you are driving, this indicates a While driving, it flashes during activation malfunction. Stop, and switch the engine of the system. After switching on the off and check the engine oil level.
Page 83 Instrument Cluster í qFour-wheel drive indicator Powertrain warning lamp All vehicles The four-wheel drive indicator lamp will come on when the transfer shift switch is If either lamp illuminates when the engine in the 4H or 4L position. This will flash is running, this indicates a fault.
Page 84 Instrument Cluster í qElectronic locking differential qWasher fluid level indicator í (ELD) indicator It illuminates when the windscreen washer fluid level goes below the The ELD indicator lamp will come on minimum mark. See Washer Fluid when the rear differential is locked. The Check (page 181).
Page 85 Instrument Cluster It will illuminate and glow orange when Left side turn indicator the outside air temperature is between 4 °C and 0 °C (39 °F and 32 °F). It will glow red when the temperature is below 0 °C (32 °F). qDoor open warning lamp The direction indicator will flash when you use the direction indicators.
Page 86 Instrument Cluster í qFront fog lamp indicator qGear shift indicator lamp (Manual only) The front fog lamp indicator will come on when you switch the front fog lamps on. It will illuminate to inform you that shifting to a higher gear may give better í...
Page 87: Audible Warnings And Indicators
Instrument Cluster qTurn indicator AUDIBLE WARNINGS The turn indicator chime will sound when AND INDICATORS the left or right turn indicator is activated. qDoor open warning qDirection indicators warning The door open warning chime will sound The direction indicator warning chime if the vehicle speed exceeds will sound if the left or right direction approximately 10 km/h (6.2 mph) and you...
Page 88 Missed lock warning chime will sound if the door is not locked after pressing the lock button. NOTE This feature is default off. To activate it, contact your Authorised Mazda Repairer. í Some models.
Page 89: Information Displays
Information Displays GENERAL INFORMATION TRIP COMPUTER qControls WARNING Do not operate the information display controls when the vehicle is moving. NOTE The information display will remain on for several minutes after you switch off the ignition. For item location: See Gauges (page 73). Press the SET/RESET button less than 2 seconds to: Select between the trip computer...
Page 90 Information Displays The trip computer display includes the following information displays: Registers the mileage of individual journeys. qDistance to empty qTripmeter (A and B) Indicates the approximate distance the vehicle will travel on the fuel remaining in the tank. Changes in driving pattern may cause the value to vary.
Page 91 Information Displays qAverage fuel consumption Indicates the current average fuel consumption. qAverage speed Indicates the average fuel consumption since the function was last reset. qInstantaneous fuel consumption Indicates the average speed calculated since the function was last reset.
Page 92: Personalised Settings
Information Displays í qOutside air temperature PERSONALISED SETTINGS qLanguage setting Shows the outside air temperature. NOTE Language set menu active The position of the trip computer display may vary depending on the Language title display information shown in the display. A choice of eleven languages are available from 01 to 11 in the order shown below:...
Page 93 Information Displays 4. Press and hold the SET/RESET button to set the currently displayed language. 5. A chime will be heard to confirm the selection. 6. The display will then return to normal operation. qUnits of measure To select metric or imperial units for outside temperature display: 1.
Page 94: Air-Conditioning
Air-Conditioning Air is directed through the evaporator PRINCIPLE OF where it is cooled. Humidity is extracted OPERATION from the air to help keep the windows free of mist. The resulting condensation is qOutside air directed to the outside of the vehicle and it is therefore normal if you see a small pool Keep the air intakes forward of the of water under your vehicle.
Page 95: Air Vents
Air-Conditioning AIR VENTS MANUAL CLIMATE CONTROL qAir distribution control Face level Face level and footwell Footwell Footwell and windscreen Windscreen You can set the air distribution control to any of the indicated positions. A small amount of air is directed towards the windscreen in positions B and C.
Page 96 Air-Conditioning qBlower qRecirculated air Press the recirculated air button to toggle between outside air and recirculated air. qSystem settings NOTE Set all controls to the positions shown. Heating the interior quickly qTemperature control Select the outside air. Blue Cold Warm Maximum cooling...
Page 97 Air-Conditioning Ventilation Cooling with outside air Switch the air conditioning on and select Face level and footwell the outside air. Face level Set the air distribution control to position Cooling the interior quickly A or position B. Set the blower and temperature to any position and select the outside air.
Page 98: Automatic Air-Conditioning
Air-Conditioning Selecting air to windscreen will AUTOMATIC CLIMATE automatically switch the A/C on and CONTROL select the outside air. Reducing interior air humidity The system controls the temperature, amount and distribution of the air flow automatically and adjusts them according to the driving and weather conditions.
Page 99 Air-Conditioning qAir distribution control qBlower Windscreen NOTE Face level Footwell When the blower is in AUTO mode, no blower setting indicators will be To adjust air distribution, press the desired illuminated. button. The combination of settings that can be selected are A, B, C, A and C and B and C.
Page 100 Air-Conditioning qTemperature control Long press of the AUTO button or selecting the temperature for the passenger s side with the rotary control on the passenger s side. The temperature for the driver s side will remain unchanged. You can now adjust the driver and passenger side temperatures independently.
Page 101 Air-Conditioning qWindscreen defrosting and demisting NOTE When the system is in auto mode and the interior and exterior temperatures are quite hot, the system selects recirculated air automatically to maximise cooling of the interior. Once the selected temperature is reached, the system will reselect outside air automatically.
Page 102: Heated Windows
Air-Conditioning HEATED WINDOWS NOTE The A/C operates only when the engine qHeated windows is running. NOTE qSwitching off the automatic air- Make sure the engine is running before conditioning operating the heated windows. Heated windscreen Press the power button to switch the system on and off.
Page 103: Seats
Seats keep sufficient distance between SITTING IN THE yourself and the steering wheel. We CORRECT POSITION recommend a minimum of 250 millimetres (10 inches) between your breastbone and the airbag cover. hold the steering wheel with your arms slightly bent. bend your legs slightly so that you can press the pedals fully.
Page 104: Front Seats
Seats qMoving the seats backwards and FRONT SEATS forwards (Manual seats) WARNING Do not use any accessory seat covers that are not specifically designed for seats with side airbags. These seat covers must be fitted by properly trained technicians. Do not adjust the seats when the vehicle is moving.
Page 105 Seats qAdjusting the height of the qAdjusting the angle of the driver's seat (Manual seats) seatback (Manual seats) Each pull or press on the lever will raise or lower the height by a small amount. WARNING Rock the seatback backwards and forwards after releasing the lever to make sure that it is fully engaged in its catch.
Page 106 Seats qFolding the seat backrest (Bench Front seat - Freestyle cab seat - Regular cab) NOTE On freestyle cab vehicles the front passenger seat can be adjusted to allow the rear passenger to gain easier access.
Page 107 Seats qMoving the seats backwards and qAdjusting the height of the forwards (Electric seats) driver's seat (Electric seats) CAUTION Do not move the front seats too close to the instrument panel.
Page 108 Seats qAdjusting the angle of the qTilting the seat (Electric seats) seatback (Electric seats)
Page 109: Head Restraints
Seats HEAD RESTRAINTS WARNING qAdjusting the head restraint Always drive with the head restraints installed when seats are being used and make sure they are properly WARNING adjusted: Driving with the head restraints Raise the rear head restraint when adjusted too low or removed is the rear seat is occupied by a dangerous.
Page 110: Rear Seats
Seats REAR SEATS CAUTION qFolding the rear seat cushion When the cushion is folded down, the cushion tether strap must be stowed in Freestyle cab the pocket provided. qFolding the rear seatback - Double cab WARNING When folding the seatbacks down, take care not to get your fingers caught between the seatback and seat frame.
Page 111: Heated Seats
Seats To fold the seatback down HEATED SEATS 1. Pull the release strap upwards. CAUTION 2. Push the seatback forwards. To return the seatback to its upright Operating this function with the engine position: off will drain the battery. 3. Push the seatback to the upright position.
Page 112: Convenience Features
Convenience features CLOCK INSTRUMENT LIGHTING DIMMER For detailed instructions on how to adjust the clock. See Setting the clock on the audio unit (page 243). NOTE Adjusting the illumination dimmer switch will alter the illumination level of the interior displays and switches. For item location: See Gauges (page 73).
Page 113: Cigar Lighter
You can use the socket to power 12 volt appliances that have a maximum current rating of 10 Amperes. Use only Mazda accessory connectors or connectors specified for use with SAE standard sockets. Press the element in to use the cigar lighter.
Page 114: Auxiliary Power Points
You can use the auxiliary power socket to power 12 volt appliances that have a maximum current rating of 10 Amperes. Use only Mazda accessory connectors or connectors specified for use with SAE standard sockets. For item location: See At a Glance (page 3).
Page 115: Overhead Console
Convenience features Type 2 OVERHEAD CONSOLE í qRear cup holders í Some models.
Page 116: Storage Compartments
Convenience features Centre console STORAGE COMPARTMENTS Driver side Passenger side...
Page 117: Auxiliary Input (Aux In) Socket
Convenience features USB PORT AUXILIARY INPUT (AUX IN) SOCKET For item location: See At a Glance (page For item location see: See At a Glance See Connectivity (page 284). (page 3). See Auxiliary input (AUX IN) socket (page 260).
Page 118: Floor Mats
FLOOR MATS WARNING We recommend the use of Genuine Do not install two floor mats, one on Mazda floor mats. top of the other, on the driver's side: Installing two floor mats, one on top WARNING of the other, on the driver's side is...
Page 119: Starting And Stopping The Engine
Any unusual driving characteristics during this period may be disregarded. qStarting the engine by towing or pushing Do not push-start your Mazda. WARNING 0 The ignition is off. Never tow a vehicle to start it: I The ignition and all main electrical Towing a vehicle to start it is circuits are disabled.
Page 120: Steering Wheel Lock
Starting and Stopping the Engine STEERING WHEEL LOCK STARTING A PETROL ENGINE When you remove the key from the ignition switch, the steering column lock is activated as soon as you turn the NOTE steering wheel. You can only operate the starter for a The steering will be unlocked when the limited period of time, for example 10 key is moved to position ACC.
Page 121 Starting and Stopping the Engine qEngine idle speed after starting 3. Start the engine. All vehicles The speed at which the engine idles immediately after starting will vary If the engine does not start, wait for a depending on the engine temperature. short period and try again.
Page 122: Starting A Diesel Engine
Starting and Stopping the Engine STARTING A DIESEL DIESEL PARTICULATE í ENGINE FILTER qCold or hot engine The DPF forms part of the emissions reduction systems fitted to your vehicle. It All vehicles filters harmful diesel particulates (soot) from the exhaust gas. NOTE qRegeneration When the temperature is below...
Page 123: Switching Off The Engine
Starting and Stopping the Engine Unlike a normal filter which requires SWITCHING OFF THE periodic replacement, the DPF has been ENGINE designed to regenerate, or clean itself to maintain operating efficiency. The qVehicles with a turbocharger regeneration process takes place automatically.
Page 124: Fuel And Refuelling
There is a risk of injury if the fuel system is The use of additives or other engine leaking. treatments not approved by Mazda is not recommended. Ethanol blended fuels up to 20% (E20) is acceptable to be used in this vehicle.
Page 125: Fuel Quality - Diesel
NOTE We recommend that you use only high quality fuel. (Ex. EN590) The use of additives or other engine treatments not approved by Mazda is not recommended. Bio-diesel blended fuels up to 10% (B10) can be used in this vehicle.
Page 126: Catalytic Converter
Fuel and Refuelling CATALYTIC CONVERTER FUEL FILLER FLAP WARNING WARNING Do not park or idle your vehicle over Take care when refuelling to avoid dry leaves, dry grass or other spilling any residual fuel from the combustible materials. The exhaust fuel nozzle.
Page 127 Fuel and Refuelling 1. Press the flap to open it. Fully insert the fuel nozzle. Lower the nozzle so that it locks in place on the fuel 2. Open the flap fully until it engages. pipe opening. Keep it resting at this Turn the fuel filler cap anti-clockwise.
Page 128: Refuelling
Real world fuel consumption is governed by many factors including; driving style, high speed driving, stop/start driving, air conditioning usage, the accessories fitted and towing etc. Your Authorised Mazda Repairer can give you advice on improving your fuel consumption.
Page 129: Transmission
Transmission MANUAL TRANSMISSION FOUR-WHEEL DRIVE qSelecting reverse gear NOTE A clicking sound from the driveline CAUTION may be heard while shifting between ranges, which is normal. Do not engage reverse gear when the vehicle is moving. This can cause damage to the transmission. NOTE Fully depress the clutch pedal and wait for three seconds before you select...
Page 130 Transmission This can be done with the vehicle moving NOTE up to 110 km/h (68 mph), but only with the accelerator pedal released. During the The four-wheel drive indicator lamp shift the indicator lamp will flash. will come on when the transfer shift switch is in the 4H position.
Page 131: Electronic Locking Differential
Transmission 1. Stop the vehicle when it is safe to do ELECTRONIC LOCKING DIFFERENTIAL 2. Fully depress the clutch pedal (manual transmission). WARNING 3. Move the transmission selector lever to the neutral (N) position (automatic The vehicle should not be operated on transmission).
Page 132: Automatic Transmission
Transmission The system will: AUTOMATIC Automatically disengage when a speed TRANSMISSION of 40 km/h (25 mph) is exceeded. qSelector lever positions Automatically re-engage when the speed drops below 30 km/h (20 mph). Automatically disengage when the ignition is turned off. If the system is selected when driving above 40 km/h (25 mph), the request is stored and will be engaged when the...
Page 133 Transmission Reverse NOTE A cold engine has a higher idle speed. WARNING This will increase the tendency for your vehicle to creep when you have Select reverse only when your vehicle selected a drive gear. is stationary and the engine is at idle speed.
Page 134 Transmission NOTE WARNING When you select position S, a gear Do not hold the selector lever change may occur depending on the permanently in accelerator pedal position in relation to actual vehicle speed. When the vehicle is stationary, only the 1st and 2nd gears can be selected.
Page 135 Transmission Lift up the cover in the centre console Stopping next to the selector lever with a suitable 1. Release the accelerator pedal and press tool. the brake pedal. Push down the locking button in the slot and simultaneously move the selector 2.
Page 136: Brakes
1. Apply the brakes and bring your method, please contact an expert repairer, vehicle to a safe stop. we recommend an Authorised Mazda Repairer. The information is made freely 2. Turn the engine off. available.
Page 137: Hints On Driving With Anti-Lock Brakes
Brakes PARKING BRAKE HINTS ON DRIVING WITH ANTI-LOCK BRAKES WARNING When the ABS is operating, the brake pedal will pulse. This is normal. Maintain Vehicles with an automatic pressure on the brake pedal. transmission should always be left The ABS will not eliminate the dangers with the selector lever in position P inherent when: (Park).
Page 138: Hill Descent Control (Hdc)
Hill Descent Control (HDC) (Some models.) PRINCIPLE OF USING HILL DESCENT OPERATION CONTROL HDC operates in conjunction with DSC to NOTE provide greater control when off-road, particularly when descending steep When the rear differential lock is slopes. HDC operation is fully automatic engaged, the HDC will not be available.
Page 139 Hill Descent Control (HDC) (Some models.) DSC indicator is illuminated and NOTE operating. Each gear has a pre-determined Electronic locking differential is minimum speed. operating. Descent speed will only increase on qHDC operation (if equipped) a slope steep enough to provide additional momentum.
Page 140: Dynamic Stability Control
Dynamic Stability Control Dynamic stability control (DSC) PRINCIPLE OF warning lamp OPERATION The DSC warning lamp will flash when the system is operating. See Warning qDynamic stability control (DSC) Lamps and Indicators (page 74). qBrake assist WARNING DSC does not relieve you of your WARNING responsibility to drive with due care and attention.
Page 141: Using Dynamic Stability Control
Dynamic Stability Control Transfer shift switch in 4H position: USING DYNAMIC Press and hold the switch for one STABILITY CONTROL second to deactivate Engine Traction Control and Trailer Sway Assist. Hill NOTE Descent Control, Hill Launch Assist and Brake Traction Control remain The system will be switched on active.
Page 142: Hill Launch Assist
Hill Launch Assist PRINCIPLE OF WARNING OPERATION Do not rely completely on Hill Launch Hill Launch Assist is a function which Assist. assists the driver in accelerating from a Hill Launch Assist is an auxiliary stop while on a slope. When the driver device for accelerating from a stop on releases the brake pedal and depresses the a slope.
Page 143 Hill Launch Assist NOTE Hill Launch Assist does not operate on a gentle slope. In addition, the gradient of the slope on which the system will operate changes depending on the vehicle's load. Hill Launch Assist does not operate if the parking brake is applied, the vehicle has not stopped completely, the clutch pedal is released (MT vehicles), or any door is open.
Page 144: Parking Aids
Parking Aids PRINCIPLE OF NOTE OPERATION On vehicles fitted with a tow bar, the rear parking aid is deactivated automatically when any trailer lamps WARNING (or lighting boards) are connected to the socket via a trailer tow module The parking aid does not relieve you we have approved.
Page 145: Using The Parking Aid Vehicles With: Rear Parking Aid
Parking Aids You will hear an intermittent tone at a USING THE PARKING distance of approximately 180 centimetres AID VEHICLES WITH: (71 inches) between the obstacle and rear REAR PARKING AID bumper and approximately 50 centimetres (20 inches) to the side. Decreasing the distance accelerates the intermittent tone.
Page 146 Parking Aids As the distance decreases the indicator moves towards the vehicle. A continuous tone will start at a distance of less than 40 centimetres (15 inches) to the rear bumper. A trailer symbol indicates there is a trailer attached and the system is disabled. Malfunction indicator.
Page 147: Rear View Camera
Parking Aids Switch the ignition and the audio unit on. í REAR VIEW CAMERA Move the transmission selector lever to reverse. WARNING The image is displayed on the rear view mirror screen. The camera may not operate correctly in The operation of the camera may the following conditions: vary depending on the ambient temperature, vehicle and road...
Page 148 Parking Aids qSwitching the rear view camera off The lines show the distance from the outer edge of the front tyre plus two inches (51 millimeters) and the rear bumper. NOTE Move the transmission selector lever from reverse gear. The display will switch off after a short period.
Page 149: Cruise Control
Cruise Control USING CRUISE CONTROL PRINCIPLE OF OPERATION WARNING WARNING Do not use cruise control in heavy traffic, on twisty roads or when the The system does not relieve you of road surface is slippery. your responsibility to drive with due care and attention.
Page 150 Cruise Control qSetting a speed NOTE If you accelerate by pressing the accelerator pedal, the set speed will not change. When you release the accelerator pedal, you will return to the speed that you previously set if the cruise control indicator is still illuminated.
Page 151 Cruise Control qCancelling the set speed qSwitching cruise control off Press the brake pedal or the CAN RES The system will not retain the speed that switch. you previously set. The cruise control indicator will not illuminate. Any of the following action may also NOTE switch off the system: The system will no longer control your...
Page 152: Load Carrying
Load Carrying GENERAL INFORMATION TAILGATE NOTE WARNING The tailgate can be lowered for better Use load securing straps to an ingress/egress of the loads. approved standard, e.g. DIN. Make sure that you secure all loose CAUTION items properly. Place luggage and other loads as Do not exceed the maximum low and as far forward as possible permissible tailgate load of 220...
Page 153: Load Retaining Fixtures
Load Carrying qLoad rest LOAD RETAINING FIXTURES WARNING í qRope hooks A loaded load rest alters the vehicle's centre of gravity and aerodynamics. NOTE Take care when cornering, driving in The number of rope hooks may vary crosswinds and at high speeds. depending on your vehicle model.
Page 154: Driving Hints
PROTECTION OF THE ENVIRONMENT qVehicles with a diesel engine How you operate your Mazda determines If the low fuel level warning lamp comes how far it will travel on a tank of fuel. Use on, refuel as soon as possible. If you...
Page 155: Running-In
Driving Hints RUNNING-IN COLD WEATHER PRECAUTIONS qTyres The functional operation of some components and systems can be affected WARNING at temperatures below -30 °C (-22 °F). New tyres need to be run-in for approximately 500 kilometres (300 miles). During this time, you may experience different driving characteristics.
Page 156: Reduced Engine Performance
Driving Hints REDUCED ENGINE DRIVING THROUGH PERFORMANCE WATER qDriving through water Your vehicle can be driven briefly if the engine overheats, without damage to the engine. The engine will continue to WARNING operate with limited power. The distance you can travel depends on ambient temperature, vehicle load, and terrain.
Page 157 Driving Hints 600 mm (23.6 inches) 4x2 (vehicles with increased ride height) and 4x4 800 mm (31.5 inches) When driving in water, engage first gear and low range (if available), maintain a steady walking pace speed keeping the bow wave in front of the vehicle and do not stop.
Page 158: Vehicle Loading
Driving Hints VEHICLE LOADING WARNING Never overload the vehicle and always observe the vehicle's weight ratings: Overloading a vehicle is dangerous. The results of overloading can have serious consequences in terms of passenger safety. Too much weight on a vehicle's suspension system can cause spring or shock absorber failure, brake failure, handling or steering problems, irregular tyre wear, tyre failure or other damage.
Page 159: Towing
Do not exceed a speed of 80 km/h (50 mph) when towing with a laden weight greater than 3,000 kg (6,613 lbs). Do not tow a trailer during the first 1,000 km (600 miles) of your new Mazda, If you do, you may damage the engine, transmission, differential, wheel bearings, and other power train components.
Page 160 Trailer Towing-Load Table. TRAILER TOWING-LOAD TABLE Because vehicle weights vary, adjustments must be made to meet the requirements in this table. For any further details and advice please consult Authorised Mazda Repairer. Max trailer Without trailer With trailer...
Page 161 Contact your Authorised Mazda Dealer for more information. See Towing equipment dimensions.(page 214) CAUTION If a Mazda genuine tow bar is not used, it could result in damage to the frame. qTyres When towing a trailer, make sure all tyres are inflated to the recommended cold-tyre pressure, as indicated on the tyre pressure chart on the driver's door.
Page 162 The trailer patch harness is available with the Authorised Mazda Repairer. qTrailer lights CAUTION Do not connect a trailer lighting system directly to the lighting system of your Mazda. This may damage your vehicle's electrical system and lighting systems. To connect the lighting system, consult an Authorised Mazda Dealer.
Page 163 Stop and re-inspect all lights and connections after driving a short distance. Driving Your Mazda will handle differently with a trailer in tow, so practice turning, backing, and stopping in a traffic-free area. Take time to get accustomed to the extra weight and length.
Page 164 Towing WARNING The overrun brake on a trailer is not controlled by the anti-lock braking system. When descending a hill, shift into a lower gear and use engine compression as a braking effect. Pay constant attention to speed and use the brakes only as needed. Holding the brake pedal down for a prolonged period may cause the brakes to overheat and lose power.
Page 165: Fuses
Fuses qPassenger compartment fuse box FUSE BOX LOCATIONS Fully open the driver's side storage Left-hand drive compartment. Right-hand drive Passenger compartment fuse box Engine compartment fuse box...
Page 166: Changing A Fuse
Have repairs to the electrical system and the replacement of relays and high current fuses carried out by an Authorised Mazda Repairer. Switch the ignition and all electrical equipment off before touching or attempting to change a fuse.
Page 167: Fuse Specification Chart
Fuses FUSE SPECIFICATION CHART qEngine compartment fuse box The equipment and installation position varies by vehicle. Fuse Ampere rating Circuits protected CEM Power A CEM Power B 3 (Petrol) Engine cooling fan 3 (Diesel) Glow plug control module ABS module Electric windows Four wheel drive (4×4) motor ground Not used...
Page 168 Fuses Fuse Ampere rating Circuits protected Blower motor Four wheel drive (4×4) motor power Starter solenoid Heated rear window 15 (Petrol) Flex-fuel pump 15 (Diesel) Vapouriser glow plug A/C Clutch Electric windows Windscreen wiper motor Windscreen wiper motor ground Cigar lighter Horn 22 (Petrol) Fuel injectors or flex-fuel valve...
Page 169 Fuses Fuse Ampere rating Circuits protected Not used Not used Ignition relay, relay coils Trailer tow Electric windows Relay Circuits switched R1 (Petrol) Not used R1 (Diesel) Key interlock Wiper on or off Horn A/C clutch Differential lock Wiper Hi/Lo R7 (Petrol) Engine cooling fan low R7 (Diesel)
Page 170 Fuses qPassenger compartment fuse box...
Page 171 Fuses The equipment and installation position varies by vehicle. Fuse Ampere rating Circuits protected Fuel pump Not used Not used Passive anti-theft system (PATS) Interior lamp, driver's door switch pack, mood lights, automatic shifter Spare Rain sensor module Tachograph Not used Not used Driver's door unlock, central double locking Stop lamp switch...
Page 172: Vehicle Recovery
Vehicle recovery TOWING POINTS TOWING THE VEHICLE ON FOUR WHEELS qAll vehicles WARNING Switch the ignition on when your vehicle is being towed. The steering lock will engage and the direction indicators and brake lamps will not work if you do not. The brake servo and the power Front towing eye steering pump do not operate unless...
Page 173 Vehicle recovery qVehicles with automatic transmission CAUTION It is recommended not to tow with the drive wheels on the ground. However, if it is required to move the vehicle from a dangerous location, do not tow your vehicle faster than 80 km/h (50 mph) or further than 80 kilometres (50 miles).
Page 174: Maintenance
Do not connect any devices other than the resale value. There is a large network of specially designed malfunction diagnosis Mazda Authorised Repairers that are there devices for servicing. If any device other to help you with their professional than the malfunction diagnosis device is servicing expertise.
Page 175: Opening And Closing The Bonnet
Maintenance OPENING AND CAUTION CLOSING THE BONNET When carrying out maintenance checks, make sure that filler caps are fitted qOpening the bonnet securely. qDaily checks Exterior lamps. Interior lamps. Warning lamps and indicators. qCheck when refuelling Engine oil level. See Engine Oil Check (page 177).
Page 176 Maintenance 4. Open the bonnet. 5. Support it with the strut. qClosing the bonnet NOTE Make sure that the bonnet is closed properly. Lower the bonnet and allow it to drop from under its own weight for the last 20 - 30 centimetres (8 - 11 inches).
Page 177: Under Bonnet Overview - Mzi 2.5
Maintenance UNDER BONNET OVERVIEW - MZI 2.5 Engine coolant reservoir cap. See Engine Coolant Check (page 178). Brake and clutch fluid reservoir cap. See Brake and Clutch Fluid Check (page 179). Engine oil filler cap . See Engine Oil Check (page 177). Engine oil dipstick .
Page 178: Under Bonnet Overview - Mz-Cd 2.2
Maintenance UNDER BONNET OVERVIEW - MZ-CD 2.2 qRHD...
Page 179 Maintenance qLHD Engine coolant reservoir cap. See Engine Coolant Check (page 178). Brake and clutch fluid reservoir cap. See Brake and Clutch Fluid Check (page 179). Engine oil dipstick . See Engine Oil Dipstick (page 176). Engine oil filler cap .
Page 180: Under Bonnet Overview - Mz-Cd 3.2 I5
Maintenance UNDER BONNET OVERVIEW - MZ-CD 3.2 I5 qRHD...
Page 181 Maintenance qLHD Engine coolant reservoir cap. See Engine Coolant Check (page 178). Brake and clutch fluid reservoir cap. See Brake and Clutch Fluid Check (page 179). Engine oil dipstick . See Engine Oil Dipstick (page 176). Engine oil filler cap .
Page 182: Engine Oil Dipstick - Mzi
Maintenance ENGINE OIL DIPSTICK ENGINE OIL DIPSTICK - - MZI 2.5 MZ-CD 2.2/MZ-CD 3.2 I5...
Page 183: Engine Oil Check
Do not top up further than the MAX mark. CAUTION Top up with fluid that meets the Mazda Make sure that the level is between the specification. See Technical MIN and the MAX marks. Specifications (page 182).
Page 184: Engine Coolant Check
CAUTION Do not top up further than the MAX mark. Top up with a 50/50 mixture of coolant and water using fluid that meets the Mazda specification. See Technical Specifications (page 182).
Page 185: Power Steering Fluid Check
The brake and the clutch systems are Top up with fluid that meets the Mazda supplied from the same reservoir. specification. See Technical Specifications (page 182). Top up with fluid that meets the Mazda specification.
Page 186: Draining The Fuel Filter Water Trap
1.5 turns. NOTE 5. Switch the ignition on to activate the in-tank pump. Only add fuel that meets the Mazda 6. Drain the water till it is replaced by a specification. See Fuel Quality clean diesel fuel. (page 118).
Page 187: Washer Fluid Check
Maintenance WASHER FLUID CHECK Top up the washer fluid reservoir when the washer fluid level indicator is on. See í Warning Lamps and Indicators (page 74). When topping up, use a mixture of washer fluid and water to help prevent freezing in cold weather and improve the cleaning capability.
Page 188: Technical Specifications
Maintenance TECHNICAL SPECIFICATIONS qVehicle fluids Lubricant Classification Engine oil - Diesel ACEA A5/B5 (prefered), SAE 5W-30 (prefered), 5W-40, (for markets with low sulphur content less than A3/B3 10W-40 350 ppm) Engine oil - Diesel ACEA E5-99, API CH-4 or (for markets with high sulphur content equal SAE 10W-30, 5W-40, 10W-40 higher and greater than 350 ppm)
Page 189: Scheduled Maintenance
Emission control and related systems The ignition and fuel systems are highly important to the emission control system and to efficient engine operation. Don't tamper with them. All inspections and adjustments must be made by an expert repairer, we recommend an Authorised Mazda Repairer.
Page 190 Maintenance qSchedule Number of months or kilometres, whichever comes first Maintenance Months 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 Interval ×1000 km 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 PETROL ENGINE Engine valve clearance Engine oil...
Page 191 Maintenance Number of months or kilometres, whichever comes first Maintenance Months 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 Interval ×1000 km 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 PETROL and DIESEL ENGINE Timing chain and tensioner Replace every 250,000 km or 10 years...
Page 192 Maintenance Number of months or kilometres, whichever comes first Maintenance Months 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 Interval ×1000 km 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 Body condition (for rust, corrosion and perforation) Hinges and catches...
Page 193 Maintenance *7 If this component(s) has been submerged in water, the fluid/oil should be replaced. *8 If the vehicle is operated primarily under any of the following conditions, rotate the tyres more often than the recommended intervals. a) Driving on bumpy roads, gravel roads, snowy roads or dirt roads b) Driving uphill and downhill frequently c) Repeated short-distance driving d) On roads having many roundabouts...
Page 194: Vehicle Care
Vehicle Care qCleaning the rear window CLEANING THE EXTERIOR CAUTION Do not scrape the inside of the rear WARNING window or use abrasives or chemical solvents to clean it. If you use a car wash with a waxing cycle, make sure that you remove the Use a clean, lint free cloth or a damp wax from the windscreen.
Page 195: Cleaning The Interior
A choice of or water applied with a soft sponge. Let products is available from your the seat belts dry naturally, away from Authorised Mazda Repairer. Read and artificial heat. follow the manufacturer's instructions. qInstrument cluster screens, LCD...
Page 196: Vehicle Battery
Vehicle battery 1. Position the vehicles so that they do JUMP-STARTING THE not touch one another. VEHICLE 2. Switch off the engine and any electrical equipment. CAUTION 3. Connect the positive (+) terminal of vehicle B with the positive (+) terminal Connect batteries with only the same of vehicle A (cable C).
Page 197: Battery Connection Points
Vehicle battery BATTERY BATTERY WARNING CONNECTION POINTS SYMBOLS qBattery labels No smoking, no naked flames, no sparks. Shield the eyes. Keep away from children. Corrosive. Note operating instructions. Explosive gas. CAUTION Do not connect to the negative (-) terminal of the flat battery.
Page 198 Vehicle battery INFORMATION FOR USERS ON COLLECTION AND DISPOSAL OF OLD EQUIPMENT AND USED BATTERIES When disposing your old battery, please refer to the information as follows. qInformation on Disposal If you wish to discard old products and used batteries, please contact your local authorities, your waste disposal service or the point of sales where you purchased the items, and ask for the correct method of disposal.
Page 199: Wheels And Tyres
The tyre pressure sensors mounted in the wheels are not designed to be used in aftermarket wheels. The use of wheels or tyres not recommended by Mazda Motor Company may affect the operation of your tyre pressure monitoring system. If the tyre pressure monitoring system indicator is flashing, the system is malfunctioning.
Page 200: Changing A Road Wheel
Wheels and Tyres Regular cab CHANGING A ROAD WHEEL qLocking wheel nuts You can obtain a replacement locking wheel nut key and replacement locking wheel nuts from your repairer using the reference number certificate. qVehicle jack WARNING The vehicle jack supplied with your vehicle should only be used when changing a wheel in emergency situations.
Page 201 Wheels and Tyres Freestyle cab 1. Pull the release strap. 2. Remove the rear seats. 3. Remove the cover and loosen the jack. 4. Remove the bolt. 5. Remove the jack. 6. Remove the tools.
Page 202 Wheels and Tyres The spare wheel is located underneath the Double cab rear of the vehicle. 1. Lift the release strap. 2. Lower the seatback. 3. Remove the locking strap. 4. Loosen the jack and remove the bolt. 5. Remove the jack. qSpare wheel NOTE Your vehicle may exhibit some unusual...
Page 203 Wheels and Tyres 2. Fully insert the jack handle into the guide hole. Turn anti-clockwise until the wheel rests on the ground, and there is slack in the lead. 3. Pass the bracket and lead through the wheel opening.
Page 204 Wheels and Tyres qJacking and lifting points CAUTION Use only the specified jacking points. If you use other positions, you may damage the body, steering, suspension, engine, braking system or the fuel lines. Emergency use only Maintenance...
Page 205 Wheels and Tyres...
Page 206 Wheels and Tyres qRemoving a road wheel WARNING Park your vehicle in such a position that neither the traffic nor you are hindered or endangered. Turn on the hazard warning flasher. Set up a warning triangle. Make sure that the vehicle is on firm, level ground with the wheels pointing straight ahead.
Page 207 Wheels and Tyres qInstalling a road wheel 3. Install the locking wheel nut key. WARNING Use only approved wheel and tyre sizes. Using other sizes could damage the vehicle and will void the warranty. See Technical Specifications (page 209). Do not fit run flat tyres on vehicles that were not originally fitted with them.
Page 208: Tyre Care
Wheels and Tyres qStowing the wheel TYRE CARE CAUTION Do not raise the spare wheel carrier without the wheel attached. Damage can occur to the winch mechanism if lowered without a wheel attached. 1. Place the wheel flat on the ground, so the outside of the wheel faces down.
Page 209: Using Winter Tyres
Wheels and Tyres If you have to mount a kerb, do so slowly USING WINTER TYRES and approach it with the wheels at right- angles to the kerb. CAUTION Examine the tyres regularly for cuts, foreign objects and uneven wear of the Make sure that you use the correct tread.
Page 210: Using Snow Chains
Wheels and Tyres USING SNOW CHAINS TYRE PRESSURE í MONITORING SYSTEM WARNING WARNING Do not exceed 50 km/h (30 mph). Do not use snow chains on snow- The tyre pressure monitoring free roads. system is not a substitute for manually checking tyre pressures. You should periodically check tyre CAUTION pressures using a pressure gauge.
Page 211 Wheels and Tyres As a driver assistance feature, your When the malfunction indicator is vehicle has a tyre pressure monitoring illuminated, the system may not be able to system. A warning lamp will illuminate detect or signal low tyre pressures. A when one or more of the tyres are malfunction may occur for a variety of significantly under-inflated.
Page 212 You should always have tyres serviced by the repaired road wheel and tyre assembly an expert repairer, we recommend an refitted to your vehicle. Authorised Mazda Repairer. When You Believe the System is Not Operating Correctly NOTE The main function of the system is to Each road wheel and tyre is fitted with a warn you when the tyre pressures are low.
Page 213 Wheels and Tyres System Warning Lamps Warning Description Action lamp 1. Make sure tyres are at the correct pressure. See Wheels and Tyres (page 193). The tyre pressures are also on the tyre inflation pressure label (located on the edge of driver door or the B-Pillar). Tyre(s) under-inflated 2.
Page 214 Wheels and Tyres Carrying Out the System Reset Procedure 1. Check the tyre pressures and inflate all the tyres to the correct pressure. 2. Press and hold the tyre pressure monitor reset switch for 3 seconds. The warning indicator blinks 3 times to acknowledge the reset procedure was successful.
Page 215: Technical Specifications
Wheels and Tyres TECHNICAL SPECIFICATIONS Wheel nut torque Wheel type Nm (lb-ft) 103 (76.5) qTyre pressures (cold tyres) Normal load Economy Full load Tyre size Front Rear Front Rear Front Rear bar (psi) bar (psi) bar (psi) bar (psi) bar (psi) bar (psi) 215/70 R16C 2.4 (35)
Page 216: Vehicle Identification
Vehicle identification VEHICLE VEHICLE IDENTIFICATION PLATE IDENTIFICATION NUMBER The vehicle identification number and maximum weights are shown on a plate Depending on the build location of your located on the bottom of the passenger vehicle, the stamped vehicle identification door aperture. number can be found in the following locations.
Page 217: Technical Specifications
Capacities and Specifications TECHNICAL SPECIFICATIONS qVehicle dimensions Regular cab Item Dimension Description Dimension in mm (inches) Maximum length - excluding rear bumper (Without box) 5124 (201.7) Maximum length - excluding rear bumper (With box) 5277 (207.8) Maximum length - With underran protection (Without box) 5227 (205.8) Maximum length - With underran protection (With box) 5277 (207.8)
Page 218 Capacities and Specifications 4-door freestyle cab Item Dimension Description Dimension in mm (inches) Maximum length - excluding rear bumper (Without box) 5124 (201.7) Maximum length - excluding rear bumper (With box) 5277 (207.8) Maximum length - With underran protection (Without box) 5227 (205.8) Maximum length - With underran protection (With box) 5277 (207.8)
Page 219: Double Cab
Capacities and Specifications Double cab Item Dimension Description Dimension in mm (inches) Maximum length - excluding rear bumper (Without box) 5124 (201.7) Maximum length - excluding rear bumper (With box) 5277 (207.8) Maximum length - With underran protection (Without box) 5227 (205.8) Maximum length - With underran protection (With box) 5277 (207.8)
Page 220 Capacities and Specifications qTowing equipment dimensions...
Page 221 Capacities and Specifications 4x2 (vehicles with increased ride height) and 4x4 Item Dimension Description Dimension in mm (inches) Attachment point - centre of tow ball (4x2) 124 ± 5 (4.8 ± 0.2) Attachment point - centre of tow ball (4x2 or 4x4) 221.5 ±...
Page 222 Capacities and Specifications Item Dimension Description Dimension in mm (inches) Centre of tow ball - side member 588 (23.1) Outside of side member 1176 (46.3) Centre of tow ball - centre of 1st attachment point (4x2) 419 ± 5 (16.5 ± 0.2) Centre of tow ball - centre of 1st attachment point 363 ±...
Page 223: Navigation Introduction
Navigation introduction GENERAL CAUTION í INFORMATION Irregular shaped CDs and CDs with a scratch protection film or self Press the relevant button on the unit bezel adhesive labels attached should not to access the system functions. This will be used. Warranty claims, where this take you into the selected mode.
Page 224: Road Safety
Read and follow all stated safety precautions. Failure to do so may increase your risk of collision and personal injury. Mazda Motor Corporation shall not be liable for any damages of any type arising from failure to follow these guidelines.
Page 225: Navigation Quick Start
Navigation Quick start qVehicles with SD navigation system NOTE The system has a large range of features, As you spell the entry the results will yet is easy and intuitive to use. Route appear in the display. guidance is shown on the display screen. The screen provides full information for The system will limit your entries to operating the system through the use of...
Page 226 Navigation Quick start NOTE If you only need to navigate to a city centre for example, full address details are not required. The route is now calculated and the screen returns to the main navigation screen with instructions on how to proceed.
Page 227: Navigation Unit Overview
Navigation unit overview Descriptions for function buttons 1-4 Function buttons 1 to 4 are context dependent, and change according to the current unit mode. Descriptions for the functions are shown at the bottom of the screen display.
Page 228 Navigation unit overview qVehicles with SD navigation system O, Q Function 1. Function 2. Seek down. CD track selection. See Station tuning control (page 246). See Track selection (page 253). On/off and volume control. Seek up. CD track selection. See Station tuning control (page 246). See Track selection (page 253).
Page 229 Navigation unit overview Information. Door lock indicator. Hazard warning flasher switch. See Hazard Warning Flashers (page 58). Door lock button. See Locking and Unlocking (page 38). Navigation. Menu select. Phone menu. See Telephone (page 263). Auxiliary, USB and iPod select. See Auxiliary input (AUX IN) socket (page 111). See Auxiliary input (AUX IN) socket (page 260).
Page 230: Loading The Navigation Data
Navigation unit overview LOADING THE í NAVIGATION DATA qLoading the navigation data 1. Load the navigation SD card into the aperture. 2. Press the NAV button. The road safety warning will be shown in the display. 3. Use the up and down arrow buttons to select the required feature.
Page 231: System Settings
System settings Most of the important settings for your Last destinations navigation unit can be accessed via the This feature allows quick access to a MENU or NAV button. The following history of previous destinations entered in section describes the various options and the system.
Page 232 System settings Special functions Nav audio mixing This feature allows you to select GPS and This feature allows you to adjust the system information or a demonstration of volume mix between the navigation voice the system functionality. output and audio source. Map display DSP settings This feature allows you to change the way...
Page 233 System settings qClock settings Set time This feature allows you to manually adjust the time. Set date This feature allows you to manually adjust the date, month and year. GPS time This feature allows you to, if in a suitable coverage area, automatically adjust the date and time using GPS.
Page 234: Navigation System
Navigation system qEco settings í ROUTE OPTIONS MENU Trailer You can set a number of options which Use this feature to change the economy alter the way a route is planned. settings of your journey relating to Using the up, down, left and right arrow whether or not you are towing a trailer buttons, you can select from the list which and if so the size of trailer being towed.
Page 235: Route Displays
Navigation system qFerry/motorail í ROUTE DISPLAYS When switched on the system will look qMap display for ferry crossings and motorail facilities on your route and automatically update Press the MAP button for a map view. your route distance and timings. This view will show your current location with your vehicle in the centre shown as qToll...
Page 236 Navigation system qNavigation display After commencing a navigation route, the default screen is the main navigation screen: Once an active route is underway, guidance will be given by on-screen information and voice prompts. Whichever audio source you wish to leave the unit in, basic turn by turn and distance information will remain on the screen in the form of a graphic inset.
Page 237: Traffic Message Channel
Traffic Message Channel í USING TMC PRINCIPLE OF í OPERATION Press the TA or TRAFFIC button to show the traffic menu page. Traffic message channel (TMC) stations are broadcast on the FM waveband. TMC qTraffic announcement is a feature that receives traffic alerts which can be used to plan alternative Traffic announcement (TA) can be turned routes and avoid hold ups.
Page 238: Map Updates
Map updates The road network is constantly changing due to new roads, changes in road classification, etc. Therefore, it is not always possible to exactly match the map data in the system to the current road network. Map information is regularly updated, but all areas are not necessarily covered to the same level of detail.
Page 239: Audio Introduction
Audio introduction IMPORTANT AUDIO INFORMATION WARNING Due to technical incompatibility, recordable (CD-R) and rewritable (CD-RW) discs may not function correctly. These CD radio units will play compact discs that conform to the International Red Book standard audio specification. Copy protected CDs from some manufacturers do not conform to this standard and playback cannot be guaranteed.
Page 240 Audio introduction...
Page 241: Audio Unit Overview
Audio unit overview CD eject. See Compact disc player NOTE (page 253). Volume control. Units have an integrated multi function CD Aperture. display situated above the CD aperture. LCD display. This shows important information regarding control of your audio unit. Seek up.
Page 242 Audio unit overview Type 2 K, M...
Page 243 Audio unit overview Type 3 CD eject. See Compact disc player (page 253). CD select. See Compact disc player (page 253). Seek down. CD track selection. See Station tuning control (page 246). See Track selection (page 253). On/off and volume control. Seek up.
Page 244 Audio unit overview M, O...
Page 245 Audio unit overview Function buttons 1 to 4 are context Function 1. dependent, and change according to the Function 2. current unit mode. Descriptions for the Seek down. CD track selection. See functions are shown at the bottom of the Station tuning control (page 246).
Page 246 Audio unit overview O, Q...
Page 247 Audio unit overview Function buttons 1 to 4 are context Function 1. dependent, and change according to the Function 2. current unit mode. Descriptions for the Seek down. CD track selection. See functions are shown at the bottom of the Station tuning control (page 246).
Page 248: Audio System Security
Audio system security SECURITY CODE Each unit incorporates a unique code that is linked to the vehicle identification number (VIN). The system will automatically check that the audio unit and vehicle match before allowing operation. If a security code message appears, please see your repairer.
Page 249: Audio Unit Clock And Date
Audio unit clock and date displays Rotate the VOLUME CONTROL to SETTING THE CLOCK adjust the hours. ON THE AUDIO UNIT Press BACK button to return to previous menu. qChanging the time Rotate the VOLUME CONTROL to The clock can be set at any time when the select minute set and enter.
Page 250 Audio unit clock and date displays Use UP and DOWN arrow buttons to adjust hours. Use RIGHT and LEFT arrow buttons to scroll to the minutes. Use UP and DOWN arrow buttons to adjust minutes. Press OK button to save the new settings qExact hour adjustment You can set the time to the beginning of...
Page 251: Audio Unit Operation
Audio unit operation ON/OFF CONTROL SOUND BUTTON Press the on/off control. This will also This will allow you to adjust the sound operate the unit for up to one hour with settings (for example bass and treble). the ignition turned off. 1.
Page 252: Waveband Button
Audio unit operation WAVEBAND BUTTON STATION TUNING CONTROL Press the RADIO button to select from the wavebands available. qSeek tuning The selector can also be used to return to radio reception when you have been Select a waveband and briefly press one listening to another source.
Page 253: Station Preset Buttons
Audio unit operation 3. Press OK to continue listening to a STATION PRESET station. BUTTONS qScan tuning This feature allows you to store your Scan allows you to listen to a few seconds favourite stations so that they can be of each station detected.
Page 254: Autostore Control
Audio unit operation AUTOSTORE CONTROL TRAFFIC INFORMATION CONTROL NOTE Many stations that broadcast on the FM This will store up to a maximum of the waveband have a TP code to signify that 10 strongest signals available, either they carry traffic programmeme from the AM or the FM waveband, and information.
Page 255 Audio unit operation qTraffic announcement volume Traffic announcements interrupt normal broadcasts at a preset minimum level that is usually louder than normal listening volumes. To adjust the preset volume: Use the volume control to make the necessary adjustment during an incoming TA broadcast.
Page 256: Audio Unit Menus
Audio unit menus AUTOMATIC VOLUME DIGITAL SIGNAL CONTROL PROCESSING (DSP) qDSP occupancy When available, automatic volume control (AVC) adjusts the volume level to This feature takes into account the compensate for engine noise and road differences in distance from the various speed noise.
Page 257: News Broadcasts
Audio unit menus NEWS BROADCASTS ALTERNATIVE FREQUENCIES Some audio units interrupt normal reception to broadcast news bulletins from Many programmemes that broadcast on stations on the FM waveband or radio the FM waveband have a programmeme data system (RDS) and enhanced other identification (PI) code, which can be network (EON) linked stations, in the recognised by audio units.
Page 258: Regional Mode (Reg)
Audio unit menus REGIONAL MODE (REG) Regional mode (REG) controls the behaviour of AF switching between regionally related networks of a parent broadcaster. A broadcaster may run a fairly large network across a large part of the country. At various times of the day this large network may be broken down into a number of smaller regional networks, typically centred on major...
Page 259: Compact Disc Player
Compact disc player TRACK SELECTION COMPACT DISC PLAYBACK Press the seek up button once to move to the next track or press it repeatedly to access later tracks. NOTE Press the seek down button once to During playback, the display indicates replay the current track.
Page 260: Fast Forward/Reverse
Compact disc player SHUFFLE/RANDOM FAST FORWARD/ REVERSE Random track playback, also known as shuffle, plays all tracks on the CD in Press and hold the seek down or up random order. buttons to search backwards or forwards within the tracks on the disc. qType 1 1.
Page 261: Repeat Compact Disc Tracks
Compact disc player REPEAT COMPACT COMPACT DISC DISC TRACKS TRACK SCANNING qType 1 The SCAN function allows you to preview each track for approximately 5 1. Press REPEAT button in CD mode. seconds. When an MP3 CD is playing, options qType 1 include REPEAT for the track, or to repeat all the tracks in the folder.
Page 262: Mp3 File Playback
Compact disc player qType 3 and 4 MP3 FILE PLAYBACK 1. Press function button 3. MP3 (MPEG 1 Audio Layer-3) is a standard technology and format for NOTE compressing audio data. This allows a more efficient use of the media. When an MP3 CD is playing, options You can play MP3 files recorded on CD- include SCAN for the CD, or just the...
Page 263 Compact disc player qMulti session qPlaying a multi session disc This is a recording method that enables When the first track of the first session adding of data using the Track-At-Once is audio CD data method. Only audio CD data of the first session is Conventional CDs begin at a CD control played back.
Page 264 Compact disc player qMP3 navigation Playback tip: To specify a desired playback order, before the folder or file MP3 tracks may be recorded on the CD in name, input the order by number (e.g., several ways. They can all be placed in 02 ), then record contents onto a the root directory like a conventional disc.
Page 265: Mp3 Display Options
Compact disc player MP3 DISPLAY OPTIONS ENDING COMPACT DISC PLAYBACK NOTE To restore radio reception on all units: Type 1 units may require repeated Press the RADIO button. button presses of the INFO button to display all the available track information.
Page 266: Auxiliary Input (Aux In) Socket
Auxiliary input (AUX IN) socket NOTE For optimum performance when using any auxiliary device set the volume on the device high. This will reduce audio interference when charging the device via the vehicle power supply socket. When fitted the Auxiliary input (AUX IN) socket permits an auxiliary device, such as an MP3 player, to be linked into the vehicle audio system.
Page 267: Audio System Care
Audio system care ANTENNA CAUTION To prevent damage to the aerial, remove it before entering a car wash or passing beneath a low overhead clearance. Fixed Aerial The radio aerial is mounted on the roof of the vehicle above the interior rear view mirror.
Page 268: Audio Troubleshooting
Audio troubleshooting Audio unit display Rectification General error message for CD fault conditions, such as cannot read the CD, data-CD PLEASE CHECK inserted, etc. Ensure disc is loaded correct way up. Clean and re-try, or replace disc with known music disc. If error persists contact your repairer. CD DRIVE General error message for CD fault conditions such as possible mechanism fault.
Page 269: Telephone
Mobile the system performance. To avoid this situation, only recommended phones should be used. Home Consult an Authorised Mazda Repairer for full details. Office...
Page 270: Bluetooth® Setup
If six Bluetooth® devices have refer to your phone user guide. already been bonded, one of these has to be debonded in order to bond a new 2. In the Bluetooth® menu on your device. phone, search for Mazda Audio and select it.
Page 271: Telephone Controls
Telephone 3. Enter the code number shown on the TELEPHONE CONTROLS vehicle display using the phone keypad. If no code number is shown on qRemote control the display, enter the Bluetooth® PIN number 0000 using the phone keypad. Voice and mode button Now enter the Bluetooth®...
Page 272: Using The Telephone
Telephone USING THE TELEPHONE NOTE You can also use the telephone keypad NOTE to select the first letter of the entry you are looking for. Press the relevant Refer to your audio guide for details number that corresponds to the letter of the controls.
Page 273 Telephone qReceiving an incoming call Ending a call Calls can be ended by: Accepting an incoming call pressing the reject call button. Incoming calls can be accepted by pressing the answer call button, or by pressing the OK button. pressing the OK button. pressing function button 4.
Page 274 Telephone qDebonding a bonded phone pressing the arrow down button to highlight REJECT and then pressing A bonded phone can be deleted from the the OK button. system at any time, unless a phone call is pressing function button 4. in progress.
Page 275: Voice Control
Voice control qSystem response PRINCIPLE OF í As you work through a voice session the OPERATION system will prompt you with a beep tone each time the system is ready to proceed. CAUTION Do not try to give any commands until the beep tone has been heard.
Page 276: Using Voice Control
Voice control (Switching audio source) í USING VOICE CONTROL When the following command is spoken out, the audio source can be switched. qSystem operation Voice command Explanation The order and content of the voice Switches the audio PLAY RADIO source to radio. controls are given in the following lists.
Page 277: Audio Unit Commands
Voice control qName tag AUDIO UNIT í The name tag functionality can support COMMANDS the phone, audio and navigation features qCD Player by using the "STORE NAME" function. You can assign name tags to items such You can control playback directly by asfavourite radio stations and personal voice control.
Page 278 Voice control "CD" "PLAY" "TRACK" "SHUFFLE ALL" "SHUFFLE FOLDER" "SHUFFLE OFF" "REPEAT FOLDER" "REPEAT TRACK" "REPEAT OFF" * Only available if the CD contains audio data files like MP3 or WMA. Track You can choose a track on your CD directly. Steps User says System answer...
Page 279 Voice control "RADIO" "AM <frequency>" "FM <frequency>" "STATION NAME" "DELETE NAME" "DELETE DIRECTORY" "PLAY DIRECTORY" "STORE NAME" "PLAY" Tune frequency This function allows you to tune your radio by voice commands. Steps User says System answer "RADIO" "RADIO" "AM <frequency>" "FM <frequency>"...
Page 280 Voice control Steps User says System answer "RADIO" "RADIO" "STORE NAME" "STORE NAME" "NAME PLEASE" "<name>" "REPEAT NAME PLEASE" "STORING NAME" "<name>" "<name> STORED" Station name This function allows you to call up a stored radio station. Steps User says System answer "RADIO"...
Page 281 Voice control Play This function switches the audio source to the radio mode. Steps User says System answer "RADIO" "RADIO" "PLAY" qAuxiliary input This function allows you to switch the audio source to the attached auxiliary input device. Steps User says System answer "LINE IN"...
Page 282 Voice control "USB" "PLAY" "TRACK" "PLAYLIST" "FOLDER" "SHUFFLE ALL" "SHUFFLE FOLDER" "SHUFFLE PLAYLIST" "SHUFFLE OFF" "REPEAT TRACK" "REPEAT FOLDER" "REPEAT OFF" * Play lists and folders activated by voice control must be assigned special filenames. USB play This function allows you to switch the audio source to the attached USB device. Steps User says System answer...
Page 283 Voice control "IPOD" "PLAY" "TRACK" "PLAYLIST" "SHUFFLE ALL" "SHUFFLE FOLDER" "SHUFFLE PLAYLIST" "SHUFFLE OFF" "REPEAT TRACK" "REPEAT FOLDER" "REPEAT OFF" * Playlist activated by voice control must be assigned special filenames. iPod Track You can choose a track off the all titles list of your iPod directly. Steps User says System answer...
Page 284 Voice control External devices - Bluetooth® These voice commands support the functionality of Bluetooth® which may be connected to the audio unit. Overview The overview below shows the available voice commands. The following lists will give further information about the complete command menu in selected examples.
Page 285 Voice control "BLUETOOTH" "PLAY" "SHUFFLE ALL" "SHUFFLE OFF" "REPEAT TRACK" "REPEAT OFF"...
Page 286: Telephone Commands
Voice control TELEPHONE í COMMANDS qPhone Your phone system allows you to create an additional phonebook. The stored entries can be dialled by voice control. Phone numbers stored by using voice control are stored on the vehicle system and not in your phone. Overview The overview below shows the available voice commands.
Page 287 Voice control "TELEPHONE" "MOBILE NAME" "DIAL NUMBER" "CALL <first name> <last name> AT <location>" "REDIAL" "ACCEPT CALLS" "REJECT CALLS" * Can be used as a shortcut. qPhone functions Redial This function allows you to redial the last dialled Dial number phone number.
Page 288: Air-Conditioning Commands
Voice control CLIMATE CONTROL NOTE í COMMANDS DTMF can only be used during an ongoing call. Operate the VOICE qClimate button and wait for the system prompt. Can only be used with vehicles installed The climate voice commands supports the with a dedicated VOICE button.
Page 289: Auto Mode
Voice control Temperature This function allows you to adjust the temperature. Steps User says System answer "CLIMATE" "CLIMATE" "TEMPERATURE <number> "TEMPERATURE DEGREES <number> (Ex. Temperature 21 DEGREES" degrees)" * Can be used as a shortcut. The temperature can be set in 0.5 degree C (1 degrees F) increments between 16 (61 degrees F) and 28 (82 degrees F) degrees C.
Page 290: Connectivity
Connectivity GENERAL INFORMATION NOTE The system is only designed to CAUTION recognise and read suitable audio files from a USB device that Take care when handling external conforms to the USB Mass-Storage devices with exposed electrical device class or an iPod. Not all connectors (such as the USB plug).
Page 291 USB 1.1 host compliant and To enable voice control for custom play supports FAT 16/32 file systems. lists, create play lists named with the structure Mazda<*> where <*> is a qInformation on audio file number 1-10. For example Mazda7 structures for external devices without any space between Mazda and the number.
Page 292: Connecting An External Device
Plug in the device, and if necessary secure only recommended devices should be it to prevent movement within the vehicle. used. Consult an Authorised Mazda Repairer Connecting an iPod for full details. It is possible to connect your iPod using...
Page 293: Using A Usb Device
Connectivity Operating the device USING A USB DEVICE Select Bluetooth® audio as the active Various icons are used to identify types of source. audio file, folders etc. Tracks can be accessed by skipping forwards and backwards using the USB device is the active source steering wheel controls, or directly from the audio unit controls.
Page 294 Connectivity qRadio NOTE Operation If you wish to jump to the top level of Select the USB device as the audio source the USB device contents, press and by repeatedly pressing the CD/AUX hold the left arrow key. button until USB appears in the display. After first connecting the USB device, the Audio control first track within the first folder will start...
Page 295 Connectivity Audio control NOTE Press the SEEK up and down keys to skip Some devices may be shown but not backwards and forwards through tracks. selectable, depending if the device is Press and hold the SEEK keys to enable connected or not. fast rewind/fast forward through track content.
Page 296: Using An Ipod
Connectivity qRadio USING AN IPOD Operation Various icons are used to identify types of Connect the iPod. See Connecting an audio file, folders etc. external device (page 286). iPod is the active source Select the iPod as the audio source by repeatedly pressing the CD/AUX button until iPod appears in the display.
Page 297 Connectivity NOTE NOTE If you wish to jump to the top level of Some devices may be shown but not the iPod contents, press and hold the selectable, depending if the device is left arrow key. connected or not. The iPod menu list for browsing contents Audio control will be available through the display.
Page 298 Connectivity Press and hold the SEEK keys to enable fast rewind/fast forward through track content. Press the scroll bar arrow keys to browse the iPod contents. Press the MENU key to enter the iPod menu. It is possible to enable shuffle and repeat functions here.
Page 299: Appendices
Appendices TYPE APPROVALS TYPE APPROVALS qFCC/INDUSTRY CANADA iPod is a trademark of Apple Inc. NOTICE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired...
Page 300: Type Approvals
Appendices TYPE APPROVALS SD Logo is a trademark.
Page 301: Electromagnetic Compatibility
Appendices ELECTROMAGNETIC COMPATIBILITY WARNING Your vehicle has been tested and certified to legislations relating to electromagnetic compatibility (72/245/EEC, the UNECE 10 Regulation or other applicable local requirements). It is your responsibility to ensure that any equipment you have fitted complies with applicable local legislations. Have any equipment fitted by properly trained technicians.
Page 302 Appendices Frequency Maximum output power Watt (Peak RMS) Aerial Positions Band MHz 1 - 30 100 W 50 - 54 100 W 3, 4, 5 68 - 87.5 50 W 3, 4, 5 142 - 176 50 W 3, 4, 5 220 - 225 50 W 3, 4, 5...
Page 303 Appendices TYPE APPROVALS Remote control NOTE We recommend that you use the remote control only in the countries listed. If the type approval of your remote control is inspected, refer to the following table.
Page 304 Appendices Remote control with flip key...
Page 305 Appendices Remote control without flip key...
Page 306 Appendices Engine immobiliser If the type approval of your engine immobiliser is inspected, refer to the following table.
Page 307 Appendices...
Page 308 Appendices...
Page 309 Appendices Alarm If the type approval of your alarm is inspected, refer to the following official test numbers.
Page 310 Appendices TYPE APPROVALS Tyre Pressure Monitoring System...
Page 311 Index Audible Warnings and Indicators ..81 Air-Conditioning ......88 Alarm warning ......81 About This Manual ........ 1 Direction indicators warning ..81 Door open warning ......81 Brakes .......... 130 Key in ignition warning ....81 ABS driving hints Lights on warning ......
Page 312 Index Automatic Air-Conditioning ....92 Booster leads Air distribution control ....93 Jump-Starting the Vehicle ... 190 Blower ........... 93 Booster Seats ........17 Cooling the interior quickly ... 95 Booster cushion (Group 3) .... 17 Recirculated air ......88 Booster seat (Group 2) ....
Page 313 Index Changing a Road Wheel ....194 Compact disc track scanning ....255 Installing a road wheel ....201 Type 1 .......... 255 Jacking and lifting points .... 198 Type 2 ......... 254, 255 Locking wheel nuts ..... 194 Type 3 and 4 ........ 256 Removing a road wheel ....
Page 314 Index Fast forward/reverse ......254 Disabling the passenger airbag Fastening the seat belts Disabling the passenger airbag ..32 Fastening the seat belts ....29 Enabling the passenger airbag ..33 Floor Mats .......... 112 Fitting the passenger airbag Fog Lamps - Front deactivation switch ......
Page 315 Index Fuel Consumption ......122 Fuel filler flap ........120 Hill descent control (HDC) ..132 Filling .......... 121 Head Restraints ........103 Vehicles equipped with cap Adjusting the head restraint ..103 system .......... 120 Removing the head restraint ..103 Fuel Quality - Diesel ......
Page 316 Index iPod Locking and Unlocking Using an iPod ......290 Child play protection function ..39 iPod connection Driver configuration mode .... 40 Connecting an external device ..286 Locking and Unlocking ....38 ISOFIX Anchor Points ......16 Locking and unlocking the doors Attaching a child restraint with a top from inside ........
Page 317 Index MP3 file playback ......256 Parking Brake ........131 File formats ......... 257 Parts and Accessories ......2 ID3 Tag Version 2 ....... 258 Personalised Settings ......86 ISO 9660 format ......256 Language setting ......86 MP3 files playback order ..... 257 Units of measure ......
Page 318 Index Rear View Camera ......141 Running-In ......... 149 Switching the rear view camera Brakes and clutch ......149 off ..........142 Engine ......... 149 Switching the rear view camera Tyres ..........149 on ..........141 Using the display ......141 Reduced Engine Performance ....
Page 319 Index Starting and Stopping the Engine ..113 Telephone controls ......265 General Information ....113 Remote control ......265 Station preset buttons ......247 Telephone setup ........263 Station tuning control ......246 Bond another Bluetooth® Manual tuning ......246 phone ...........
Page 320 Index Tyre Care ..........202 Using Snow Chains Tyre Pressure Monitoring System ..204 Using Snow Chains ..... 204 Tyre Pressures Using the Parking Aid - Vehicles With: Technical Specifications ....209 Rear Parking Aid ........ 139 Tyres Using the telephone ......266 Wheels and Tyres ......
Page 321 Index Warning Lamps and Indicators .... 74 ABS warning lamp ......74 Vehicle Identification Number ..210 Airbag warning lamp ..... 75 Voice control ........49 Brake system warning lamp ..74 Principle of Operation ....269 Cruise control ........ 80 Direction indicators .......
Page 322 Index Washing Cleaning the Exterior ....188 Waveband button ........ 246 Wheels and Tyres ....... 193 General Information ....193 Technical Specifications ....209 Windscreen Washers ......51 Windscreen Wipers ......50 Intermittent wipe ......50 Winter Tyres Using Winter Tyres ..... 203 Wipers and Washers ......

Mazda BT-50 2017 Owner's Manual

Quick Links

Related Manuals for Mazda BT-50 2017

Summary of Contents for Mazda BT-50 2017