ICON Health & Fitness NordicTrack 2500 R User Manual page 7

PROBLEM: The walking belt slows when walked on
SOLUTION: a. If an extension cord is needed, use only a 3-conductor, 1mm
than 1.5 m (5 ft.).
b. If the walking belt is overtightened, treadmill perfor-
mance may decrease and the walking belt may be-
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
rear roller adjustment bolts counterclockwise, 1/4 of a
turn. When the walking belt is properly tightened, you
should be able to lift each side of the walking belt 5 to
7 cm (3 to 4 in) off the walking platform. Be careful to
keep the walking belt centred. Plug in the power cord,
insert the key and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
c. If the walking belt still slows when walked on, please call our Customer Service Department, toll-
free.
PROBLEM: The walking belt is off-centre or slips when walked on
SOLUTION: a. If the walking belt is off-centre, first remove the key and
UNPLUG THE POWER CORD. If the walking belt has
shifted to the left, use the allen wrench to turn the left
rear roller bolt clockwise 1/2 of a turn. If the walking belt
has shifted to the right, turn the left rear roller bolt coun-
terclockwise 1/2 of a turn. Be careful not to overtighten the
walking belt. Plug in the power cord, insert the key, and
run the treadmill for a few minutes. Repeat until the walk-
ing belt is centred.
b. If the walking belt slips when walked on, first remove the
key and UNPLUG THE POWER CORD. Using the allen
wrench, turn both rear roller bolts clockwise, 1/4 of a turn.
When the walking belt is correctly tightened, you should
be able to lift each side of the walking belt 5 to 7 cm (3 to
4 in) off the walking platform. Be careful to keep the walk-
ing belt centred. Plug in the power cord, insert the key and
carefully walk on the treadmill for a few minutes. Repeat
until the walking belt is properly tightened.
PROBLEM: The incline of the treadmill does not change correctly or does not change when iFIT.com
CD's and videos are played
SOLUTION: a. With the key in the console, press one of the Incline buttons. Whilst the incline is changing, re-
move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
2 (14-gauge) cord that is no longer
b
5–7 cm
Rear Roller Adjustment Bolts
a
b
26
4. Pull the Upright Wire Harness (101) up through a
Handrail Spacer (114). Place the Handrail Spacer on the
right Upright (110) as shown, with the cutout turned to-
ward the treadmill (see inset drawing A). Place the other
Handrail Spacer on the left Upright, with the cutout turned
toward the treadmill.
Connect the Upright Wire Harness (101) to the wires ex-
tending from the Console Base (76). Insert the connec-
tors and the Upright Wire Harness into the hole in the
Console Base (refer to inset drawing B).
Set the Handrail (89) on the Handrail Spacers (114),
being careful not to pinch the Upright Wire Harness (101).
5. Insert two Handrail Bolts (111) with Handrail Washers
(112) and Handrail Bushings (113) into the right Upright
(110) and the right Handrail Spacer (114). Turn the
Handrail Bushings so they fit against the Upright with the
thick sides of the Bushings toward the centre of the tread-
mill (refer to the inset drawing). Lift the right Handrail (89)
slightly and align the Bolts with the holes in the Handrail.
Loosely thread the Bolts into the Handrail. Do not
tighten the Bolts yet.
See the inset drawing. Remove the Handrail Bolt (111)
used in step 3. Reach inside the left Upright (110) and
spread the tabs on the Grounding Bracket (115) to allow a
Bolt to pass through the Grounding Bracket. Attach the left
Handrail (89) as described above. Make sure that the
Handrail Bushings (113) are turned properly and that the
Bolt goes through the Grounding Bracket. Tighten all
four Handrail Bolts. Press an Upright Endcap (116) into
each Upright.
6. Make sure the Lock Knob Sleeve (106) is pressed into
the left Upright (110).
Make sure that the Lock Pin Collar (105) and the Spring
(104) are on the Lock Pin (102). Insert the Lock Pin into
the Lock Knob Sleeve (106) and the left Upright (110).
Next, press the Lock Knob Spacer (107) onto the left
Upright. Tighten the Lock Knob (108) onto the Lock Pin.
7. Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a
secure place. The allen wrench is used to adjust the walking belt (see page 26). To protect the floor or car-
pet from damage, place a mat under the treadmill.
A
4
Cutout
76
114
89
101
B
110
101
114
76
5
89
116
110
113
114
Thick
Side
112
113
112
111
6
110
108 106
104
107
105
102
7
110
89
115
111