GE F35 Instruction Manual page 231

5 SETTINGS
Table 5–9: F35 FLEXLOGIC™ OPERANDS (Sheet 5 of 7)
OPERAND TYPE OPERAND SYNTAX
ELEMENT: TELEPRO CH1 FAIL
Teleprotection TELEPRO CH2 FAIL
channel tests TELEPRO CH1 ID FAIL
TELEPRO CH2 ID FAIL
TELEPRO CH1 CRC FAIL
TELEPRO CH2 CRC FAIL
TELEPRO CH1 PKT LOST
TELEPRO CH2 PKT LOST
ELEMENT: TELEPRO INPUT 1-1 On
↓
Teleprotection
inputs/outputs TELEPRO INPUT 1-16 On
TELEPRO INPUT 2-1 On
↓
TELEPRO INPUT 2-16 On
ELEMENT TRIP BUS 1 PKP
Trip bus TRIP BUS 1 OP
TRIP BUS 2...
ELEMENT: UNDERFREQ 1 PKP
Underfrequency UNDERFREQ 1 OP
UNDERFREQ 1 DPO
UNDERFREQ 2 to 6
FIXED OPERANDS Off
On
INPUTS/OUTPUTS: Cont Ip 1
Contact inputs Cont Ip 2
↓
Cont Ip 1
Cont Ip 2
↓
INPUTS/OUTPUTS: Cont Op 1
Contact outputs, Cont Op 2
↓
current
(from detector on
form-A output only)
INPUTS/OUTPUTS: Cont Op 1
Contact outputs, Cont Op 2
voltage ↓
(from detector on
Cont Op 1
form-A output only)
Cont Op 2
↓
INPUTS/OUTPUTS DIRECT INPUT 1 On
↓
Direct inputs
DIRECT INPUT 32 On
INPUTS/OUTPUTS: RemDPS Ip 1 BAD
Remote double- RemDPS Ip 1 INTERM
point status inputs
RemDPS Ip 1 OFF
RemDPS Ip 1 ON
REMDPS Ip 2...
INPUTS/OUTPUTS: REMOTE INPUT 1 On
Remote inputs ↓
REMOTE INPUT 32 On
INPUTS/OUTPUTS: Virt Ip 1
Virtual inputs ↓
Virt Ip 64
INPUTS/OUTPUTS: Virt Op 1
Virtual outputs ↓
Virt Op 96
GE Multilin
OPERAND DESCRIPTION
Channel 1 failed
Channel 2 failed
The ID check for a peer relay on channel 1 has failed
The ID check for a peer relay on channel 2 has failed
CRC detected packet corruption on channel 1
CRC detected packet corruption on channel 2
CRC detected lost packet on channel 1
CRC detected lost packet on channel 2
Flag is set, Logic =1
↓
Flag is set, Logic =1
Flag is set, Logic =1
↓
Flag is set, Logic =1
Asserted when the trip bus 1 element picks up.
Asserted when the trip bus 1 element operates.
Same set of operands as shown for TRIP BUS 1
Underfrequency 1 has picked up
Underfrequency 1 has operated
Underfrequency 1 has dropped out
Same set of operands as shown for UNDERFREQ 1 above
Logic = 0. Does nothing and may be used as a delimiter in an equation list;
used as 'Disable' by other features.
Logic = 1. Can be used as a test setting.
On (will not appear unless ordered)
On (will not appear unless ordered)
↓
Off (will not appear unless ordered)
Off (will not appear unless ordered)
↓
IOn (will not appear unless ordered)
IOn (will not appear unless ordered)
↓
VOn (will not appear unless ordered)
VOn (will not appear unless ordered)
↓
VOff (will not appear unless ordered)
VOff (will not appear unless ordered)
↓
Flag is set, logic=1
↓
Flag is set, logic=1
Asserted while the remote double-point status input is in the bad state.
Asserted while the remote double-point status input is in the intermediate
state.
Asserted while the remote double-point status input is off.
Asserted while the remote double-point status input is on.
Same set of operands as per REMDPS 1 above
Flag is set, logic=1
↓
Flag is set, logic=1
On Flag is set, logic=1
↓
On Flag is set, logic=1
On Flag is set, logic=1
↓
On Flag is set, logic=1
F35 Multiple Feeder Protection System
5.5 FLEXLOGIC™
5
5-95