Manufacturer's Warranty; Limitations Of Warranty - Hollywog WiTouch Pro TENS User Manual

ISO 7010-M002
IEC 60417-5333
ISO 7000-0626
ISO 60417-5140
ISO 7000-0434B

Manufacturer's Warranty

Hollywog, LLC warrants the original purchaser that the WiTouch Pro device ("Product") is free from defects in materials and workmanship for one year
from the date of original purchase, except as noted below. During the stated one-year period, Hollywog, LLC shall, at no charge, replace a unit found to
be defective with an equivalent or current version of the owner's model. For warranty service, contact Hollywog at +1 423 305 7778 or info@hollywog.
com. Remember to retain the original receipt of purchase, packaging, and the device.

Limitations of Warranty

This warranty is subject to the following exceptions and limitations:
1. The one-year warranty only will be extended to the WiTouch Pro device. The warranty excludes the refill gel pads and the WiTouch Pro app.
2. This warranty is limited to replacement due to defects in parts or workmanship. Hollywog, LLC shall not be required to replace any Products which
malfunction or are damaged due to abuse, accidents, alteration, misuse, neglect, exposure to or submersion in water, or maintenance by someone
other than Hollywog, LLC, or failure to operate the instrument in accordance with instructions. The WiTouch Pro device is manufactured with water
detection technology to detect exposure to water that may cause damage to the electronics and will void the Product warranty.
3. Hollywog, LLC assumes no liability for malfunction or damages to the Products caused by the use of the Products when used with gel pads other
than WiTouch Pro refill gel pads manufactured or recommended by Hollywog, LLC.
4. Hollywog, LLC makes no warranty of the performance of the Products when used with gel pads other than WiTouch Pro refill gel pads manufactured
or
recommended by Hollywog, LLC or when the gel pads are altered or modified in any manner.
5. Hollywog, LLC makes no warranty of the performance of the Product when used with any software or apps other than Hollywog's WiTouch Pro app.
6. Hollywog, LLC reserves the right to make changes in design of the Product without obligation to incorporate such changes into previously
manufactured Products.
HOLLYWOG, LLC MAKES NO OTHER EXPRESS WARRANTY FOR THIS PRODUCT. THE OPTION OF REPLACEMENT, DESCRIBED ABOVE, IS
HOLLYWOG, LLC'S ONLY OBLIGATIONS UNDER THIS WARRANTY.
IN NO EVENT SHALL HOLLYWOG, LLC BE LIABLE FOR INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES, EVEN IF HOLLYWOG, LLC
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
The WiTouch Pro is intended for use in the electromagnetic environment specified below. The customer or the user of the WiTouch
®
assure that it is used in such an environment.
Emissions test
RF emissions
CISPR 11
RF emissions
CISPR 11
Harmonic emissions
IEC 61000-3-2
Voltage fluctuations / flicker
emissions
IEC 61000-3-3
The WiTouch Pro is intended for use in the electromagnetic environment specified below. The customer or the user of the WiTouch
®
that it is used in such an environment.
Immunity test
Electrostatic discharge (ESD)
IEC 61000-4-2
Electrical fast transient/burst
IEC 61000-4-4
Surge
IEC 61000-4-5
Voltage dips, short interruptions
and voltage variations on power
supply input lines
IEC 61000-4-11
Power frequency (50/60 Hz)
magnetic field
IEC 61000-4-8
Symbol Glossary
Refer to instruction manual/booklet
Type BF Applied Part
Keep dry
Non-ionizing electromagnetic radiation
Caution
Guidance and manufacturer's declaration – electromagnetic emissions
Compliance Electromagnetic environment – guidance
Group 1 The WiTouch
RF emissions are very low and are not likely to cause any interference in nearby
electronic equipment.
Class B The WiTouch
connected to the public low-voltage power supply network that supplies buildings
used for domestic purposes.
Not applicable
Not applicable
Guidance and manufacturer's declaration – electromagnetic immunity
IEC 60601 test level
±15 kV contact
±15 kV air
IEC 61000-4-4 (Not applicable, no AC mains connection)
IEC 61000-4-5 (Not applicable, no AC mains connection)
IEC 61000-4-11 (Not applicable, no AC mains connection)
3 A / m
Pro uses RF energy only for its internal function. Therefore, its
®
Pro is suitable for use in all establishments other than those directly
®
Compliance level Electromagnetic Environment/Guidance
±15 kV contact Floors should be wood, concrete or ceramic tile.
±15 kV air If floors are covered with synthetic material, the
relative humidity should be at least 30 %.
3 A / m Power frequency magnetic fields should be at
levels characteristic of a typical location in a typical
commercial or hospital environment.
Pro should
®
Pro should assure
®