Emergency Detail Information 2 - JVC HR-J271MS Service Manual

www.freeservicemanuals.info
: Mechanism Sensor Information
3 –
[Common table of MN and HD]
Display
S-VHS SW
0– VHS
1– VHS
2– VHS
3– VHS
4– VHS
5– VHS
6– VHS
7– VHS
8– S-VHS
9– S-VHS
A– S-VHS
B– S-VHS
C– S-VHS
D– S-VHS
E– S-VHS
F– S-VHS
: Mechanism Mode Position
– 4
[Table of MN]
Display
-0 Initial value
-1 EJECT position
-2 Housing operating
-3 U/L STOP position
-4 Tape being loaded/unloaded (When the pole base is located on the front
side of the position just beside the drum)
-5 Tape being loaded/unloaded (When the pole base is located on the rear
side of the position just beside the drum)
-6 Pole base compressed position
-7 FF/REW position
-8 Between FF/REW and STOP with pinch roller compression ON
-9 STOP with pinch roller compression OFF
-A Between STOP with pinch roller compression OFF and REV
-B REV (REV STILL/SLOW) position
-C Between REV and FWD
-D FWD (FWD STILL/SLOW) position
-E Between FWD and PLAY
-F PLAY position
[Table of HD]
Display
–0 EJECT position
–1 U/L STOP position
–2 Tape being loaded/unloaded (When the pole base is located on the rear
side of the position just beside the drum)
–3 FF/REW position
–4 STOP with pinch roller pressure off
–5 REV (REV STILL/SLOW) position
–6 FWD (FWD STILL/SLOW) position, PLAY position
–7 Intermediate position during transition between other mechanism modes
Note:
• As the display is always "–7" at any intermediate position
between mechanism modes, the position of transitory
EMG may sometimes not be locatable.
Mechanism Sensor Information
REC SAFETY SW START SENSOR
Tab broken ON
Tab broken ON
Tab broken OFF
Tab broken OFF
Tab present ON
Tab present ON
Tab present OFF
Tab present OFF
Tab broken ON
Tab broken ON
Tab broken OFF
Tab broken OFF
Tab present ON
Tab present ON
Tab present OFF
Tab present OFF
Mechanism Mode Position
Mechanism Mode Position
Digitized in Heiloo Netherland
1.6.5

Emergency detail information 2

The type of the cassette tape and the cassette tape winding po-
sition can be confirmed based on the figure in EMG detail infor-
END SENSOR
mation 2 .
ON
[FDP display]
OFF
ON
5 6
: :
* *
*
OFF
5
ON : Type of the cassette tape in use 1
*
OFF
6
: Winding position of the cassette tape in use
*
ON
: Type of the cassette tape in use 2 (Winding area)
7
*
OFF
ON
Note:
OFF
• EMG detail information 2 is the reference information
ON
stored using the remaining tape detection function of the
OFF
cassette tape. As a result, it may not identify cassette cor-
ON
OFF
rectly when a special cassette tape is used or when the
ON
tape has variable thickness.
OFF
5
: Cassette tape type 1
*
Display
00 Cassette type not identified
16 Large reel/small reel (T-0 to T-15/T-130 to T-210) not classified
82 Small reel, thick tape (T-120) identified/thin tape (T-140) identified
84 Large reel (T-0 to T-60) identified
92 Small reel, thick tape (T-130) identified/thin tape (T-160 to T-210) identified
93 Small reel, thick tape/C cassette (T-0 to T-100/C cassette) not classified
C3 Small reel, thick tape/C cassette (T-0 to T-100/C cassette) being classified
D3 Small reel, thick tape/C cassette (T-0 to T-100/C cassette) being classified
E1 C cassette, thick tape (TC-10 to TC-20) identified
E2 Small reel, thick tape (T-0 to T-100) identified
E9 C cassette, thin tape (TC-30 to TC-40) identified
F1 C cassette, thick tape/thin tape (TC-10 to TC-40) not classified
Notes:
• Cassette tape type
transition and the identification count is variable depending on
the cassette tape type. If an EMG occurs in the middle of identi-
fication, the cassette tape type may not be able to be identified.
• If other value than those listed in the above table is displayed,
the cassette tape type is not identified.
6
: Cassette tape winding position
*
The cassette tape winding position at the moment of EMG is
displayed by dividing the entire tape (from the beginning to the
end) in 22 sections using a hex number from "00" to "15".
"00" : End of winding
"15" : Beginning of winding
"FF" : Tape position not identified
: Cassette tape type 2 (Winding area)
7
*
Display
00 Cassette type not identified
07 Small reel, thick tape
08 - 0E C cassette, thick tape
09 - 15 C cassette, thick tape
0A - 0B Small reel, thick tape
0A - 16 C cassette, thin tape
0A - 16 C cassette, thin tape
0D - 0F Small reel, thick tape
11 - 14 Small reel, thick tape
15 - 18 Small reel, thick tape
17 - 1A Small reel, thick tape
19 - 1D Small reel, thick tape
1D - 21 Small reel, thick tape
1E - 1F Small reel, thin tape
1F - 23 Small reel, thick tape
21 - 23 Small reel, thin tape
21 - 23 Small reel, thin tape
22 - 24 Small reel, thick tape
22 - 24 Small reel, thin tape
22 - 24 Small reel, thin tape
22 - 23 Large reel
23 - 24 Large reel
25 - 26 Large reel
27 - 29 Large reel
29 - 2B Large reel
2D - 2F Large reel
Note:
• The values of cassette tape type 2 in the above table are
typical values with representative cassette tapes.
7
Cassette Tape Type 1
1 is identified a few times during mode
Cassette Tape Type 2
T-5
TC-10
TC-20P
T-20
TC-30
TC-40
T-40
T-60
T-80/DF-160
T-80/DF-180
T-100
T-120/DF-240
T-140
T-130
T-160
T-168
DF-300
T-180/DF-380
T-210/DF-420
T-5
T-10
T-20
T-30
T-40
T-60
4/5/2017
1-9