Welcome Thank you for purchasing our HDCVI camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference! Important Safeguards and Warnings 1.Electrical safety ...
Page 4
Please do not provide two or more power supply modes for the device, otherwise it may cause damage to the device. Statement Please refer to the actual product for more details; the manual is just for reference. The manual will be regularly upgraded according to the product update;...
1 General Introduction 1.1 Overview This series HDCVI camera conforms to the HDCVI standard. It supports video signal high- speed long distance transmission without any delay. It can be controlled by the HCVR conforming to the HDCVI. 1.2 Features Adopts high performance CMOS image sensor, megapixel definition.
2 Device Framework 2.1 Structure Dimension Please refer to Figure 2-1 for the dimension of model A, B, C and D. The unit is mm (inch). Figure 2-1 Please refer to Figure 2-2 for the chassis dimension of model A, B, C and D. The unit is mm (inch).
Figure 2-4 2.2 Cable Port Note The figures are for reference only, which are used to know the function of cable port. Different devices may have different cables, please refer to the actual device for more details. Please refer to Figure 2-5 for mobile aviation port. Figure 2-5 Please refer to Figure 2-6 for the cable sequence of HD aviation port.
Page 8
Figure 2-8 Please refer to Figure 2-9 for the video output port. Figure 2-9 Please refer to Figure 2-10 for the audio input port. Figure 2-10...
3 Installation Caution: Please install the device in time after it is taken apart, which is to avoid the camera module being exposed to damp environment for too long. Before the installation, please make sure the installation surface is thick enough to sustain at least 3X weight of the camera.
Figure 3-2 So far, the device installation and cable connection have been completed, you can check device monitoring image via back-end coding device. 3.1.2 Screw Fixing Scheme Figure 3-3...
Step 1 Take down the pedestal. Loosen the locking screws ⑦ anticlockwise to make it separate. Step 2 Mark pedestal ③ mounting hole sites on the mounting surface ①, and dig three expansion bolt bottom holes on the mounting hole sites. Then insert expansion bolts ② into the mounting holes and lock them firmly.
Page 12
Step 1 Take out the 3M adhesive ②from the device accessory bag and stick it on the camera pedestal ③. Step 2 Paste the camera onto the mounting surface (front windshield) ① according to the monitoring location of the camera ⑤. Step 3 Connect device cable to the back-end HCVR device.
4 Menu 4.1 HCVR Settings This HDCVI camera series can adjust OSD menu via coaxial control. After connected the camera to the HDCVI series HCVR, from Main Menu->Setting->System->PTZ, you need to select the channel number for access and set control mode as HDCVI and the protocol as HD- CVI.
Figure 4-2 4.3 Menu Operation Click the right mouse button and select “PTZ Control”, then you will see the “PTZ Setup” menu, which is as shown in Figure 4-3 and Figure 4-4. Figure 4-3...
Page 15
Figure 4-4 See Table 4-1 for the details of button functions. Button Function Open menu Select menu item 、 Select menu value 、 Table 4-1 If there is “ ” in the parameter value, click the “Enter” button in “Menu Operation” interface to go to the 2nd menu.
Appendix Ⅰ Maintenance Attention Please maintain the device according to the following instructions in order to ensure the image effect and long-term stable operation of the device. Maintenance for lens and mirror surface The lens and mirror surface are covered with antireflection coating, so it may produce hazardous substance and lead to performance reduction or scratch, dimness etc.