Table of Contents General Introduction ........................1 Overview ........................1 Features.........................1 Functions ........................1 Specifications ........................2 Framework...........................4 Dimensions........................4 5-Direction Buttons Settings ..................5 Installation ...........................6 Menu.............................9 HDCVI Series DVR Settings..................9 Menu List ........................10 Note ..........................11 Appendix Toxic or Hazardous Materials or Elements ...............12...
Page 3
Welcome Thank you for purchasing our HDCVI camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference!
Important Safeguards and Warnings 1.Electrical safety All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated 12V DC in the IEC60950-1. We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation.
Page 5
Please shut down the device and then unplug the power cable before you begin daily maintenance work. Use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the device. Please put the dustproof cap to protect the CMOS component when you do not use the camera.
1 General Introduction 1.1 Overview This series megapixel HD camera conforms to the HDCVI standard. It supports video signal high-speed long distance transmission without any delay. It can be controlled by the DVR conforming to the HDCVI. 1.2 Features High-performance CMOS image sensor, megapixel definition. Default sync-focus lens, coaxial cable to control lens zoom and focus.
Please refer to the following sheet for specification. Model 1 Megapixel HDCVI ICR Sync-Focus 1 Megapixel HDCVI ICR Sync-Focus Dome Camera IR Dome Camera Parameter HAC-HD3103P/N HAC-HDW3103P/N 1/3" 1.3 Mega Pixels CMOS Video Processor PAL/NTSC Video Format 1280(H)×960(V) Effective Pixel Min Illumination 0.01Lux@(F1.2,AGC ON),0 Lux...
Page 8
SAVE/CANCEL/RESET EXIT Max IR Distance Transmission Over 500m via 75-3 coaxial cable. Distance Working Temperature -30℃~+60℃. Humidity is less than 95%(no condensation) /Humidity Power DC 12V±10% Power Consumption 3.2W MAX (Input:12V 0.27A) 6.5W MAX (Input:12V 0.54A) Φ140.3×112.7 Dimension(mm) 400g Weight Wall mount/in ceiling mount Installation Mode...
2 Framework 2.1 Dimensions Please refer to the following figure for dimension information. The unit is mm. See Figure 2-1. Figure 2-1 Please refer to the following two figures for structure information. See Figure 2-2 and Figure 2-3. Figure 2-2...
Figure 2-3 Important The 5-direction control buttons on the composite cable does not have the waterproof capability. Please make sure you have taken necessary precautions before the operation, otherwise the camera may result in malfunction. Disconnect (such as cut off) the composite cable between the 5-direction buttons and the camera, you can not control the camera focus and OSD.
3 Installation Important Before the installation, please make sure the installation surface can sustain at least 3X weight of the bracket and the camera. The dome camera usually uses the ceiling installation. It can be installed on the ceiling or the wall.
Page 12
Figure 3-1 Step 4 Adjust the lens angle to a proper position and then fix the screws to fasten the lens. See Figure 3-2. Figure 3-2 Step 5 Turn clockwise to put the enclosure back to the pedestal. Now you have completed the device installation and cable connection.
Page 13
You can use the terminal encode devices to view the monitor video.
4 Menu 4.1 HDCVI Series DVR Settings Note The following operation and interfaces for reference only. Please refer to the HDCVI series DVR user’s manual for detailed information. After connected the camera to the HDCVI series DVR, from Main Menu->Setting->System- >PTZ, you need to set control mode as HDCVI and the protocol as DH-SD1.
Click up/down button to view all the items on the left pane of the following list. Click left/right button to set the corresponding values on the right pane of the following list. If there is “ ”, click confirm button to go to the 2nd menu. Repeat the previous steps to set detailed value. Click Return button to go back to the previous menu interface.
IMAGE SHARPN DETAIL AUTO/MANUAL VALUE 0-15(For manual mode only) EDGE AUTO/MANUAL VALUE 0-15(For manual mode only) RETURN CONTR 0-255 SATURA 0-15 TION BRIGHT 70-250,+10 NESS RETURN EXIT SAVE CANCEL RESET 4.3 Note Parameter Function 3DNR It is to reduce video noise. The larger the number is, the lower the noise is.
Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Cr VI PBDE Circuit Board ○ ○ ○ ○ ○ ○ Component Device Construction ○ ○ ○ ○ ○ ○ Material Wire and Cable ○ ○...