Subscribe to Our Youtube Channel
Related Manuals for Lumber Jack BS228
Summary of Contents for Lumber Jack BS228
- Page 1 SAFETY AND OPERATING MANUAL 9” Bench Top Band Saw BS228 ORIGINAL INSTRUCTIONS BS228...
-
Page 2: Table Of Contents
Closely observe all safety information in these instructions! General Power Tool Safety Warnings………………………………….…..01 Symbols & Cable Rating Chart ……….…………………………………….………05 Machine Details and Product Features……….…………………………….….06 Assembly……………………………………………………………………………………..08 Operation……………………………………….…………………………………………..14 Maintenance and Service……………………………………………………..……..15 Lumberjack Guarantee………….…………………………………………………….17 Declaration of Conformity……………………………………………………………19 Parts List…………..………………………………………………………………………...20 Parts Diagram………………………………………………………………………………24 BS228... -
Page 3: General Power Tool Safety Warnings
A wrench or a key left c) Do not expose power tools to rain or wet attached to a rotating part of the power tool may conditions. Water entering a power tool will result in personal injury. increase the risk of electric shock. BS228... - Page 4 Use power tools only with specifically operate the power tool. Power tools are designated battery packs. Use of any other dangerous in the hands of untrained users. battery packs may create a risk of injury or fire. BS228...
- Page 5 Damaged cables increase the risk of an or when inadvertently coming into contact with electric shock. the saw blade. b) Never remove cutting remainders, wood chips, etc. from the sawing area while the machine is running. BS228...
- Page 6 The smaller the gauge number of the wire the greater the capacity of the cord. e) When using a cable reel, always unwind the cable completely. BS228...
-
Page 7: Symbols & Cable Rating Chart
Caution! Wear a dust mask. Amperes 7.5M 0 – 2.0 2.1 – 3.4 3.5 - 5.0 5.1 – 7.1 7.1 – 12.0 12.1 – 20.0 BS228... -
Page 8: Machine Details And Product Features
5. Push stick Push Stick 6. 8-10mm wrench Rip Fence 7. Hex wrench(2.5mm, 4mm, 6mm) 8. Lifting handle 9. Foot A 10. Foot B 11. Pan head screw and washer 12. M6 hex nut 13. Hook BS228 AIR6V AIR6V AIR6V AIR6V... - Page 9 MACHINE DETAILS AND PRODUCT FEATURES BS228 AIR6V AIR6V AIR6V AIR6V...
-
Page 10: Assembly
– Attach foot A & B to band saw by using pan head screw and washer.. – Place the band saw on a workbench for next assembly. – Stand the band saw up on to its stand and then tighten the nuts fully on the braces. BS228... - Page 11 Tighten the saw table to the saw frame forming screws (not provide). by turning the table lock lever clockwise. – Place the fence and miter gauge onto the table. – Attach the D-nut, washers, and wing screw to the saw table. BS228...
- Page 12 Angle adjustment Table locking knob handle Adjusting the Blade If the saw blade does not run in the center of the rubber tyre, the tracking needs to be corrected by adjusting the tilt of the upper band saw wheel. BS228...
- Page 13 (the upper blade guide should be set approx. 3mm above the workpiece). – Set upper blade guide with the adjusting knob to the desired height by loosening the locking knob. After adjustment, be sure to tighten the lock knob. BS228...
- Page 14 Replaced the D-nut, washers, and wing screw. – Close the upper and lower cover. Close the cover of upper guide assembly Then: Align the saw blade Adjust the blade tension Adjust the upper blade guide and lower blade guide BS228...
- Page 15 ASSEMBLY INSTRUCTIONS Upper cover The cover of upper guide Lower cover Quick release handle BS228...
-
Page 16: Operation
– Turn of machine and LED light. Using miter gauge Push stick The miter gauge is inserting into the table slot from the table front edge. For miter cuts, the miter gauge can be turned to 60º in both directions. BS228... -
Page 17: Maintenance And Service
– Open the lower cover. drawer. It can be easily pulled out and cleaned. – Slacken the drive belt by turning the knob clockwise. – Put the drive belt on the correct drive wheels as required. Dust drawer BS228... - Page 18 – Remove the blade and clean both top and bottom pulleys before installing the new blade. – Tighten the saw blade tension knob, and replace the guide rail and close the top and bottom covers. BS228...
-
Page 19: Lumberjack Guarantee
This letter should be then sent with proof BS228... - Page 20 This Guarantee is offered as an extra benefit and does not affect your statutory rights as a consumer. 4. Notice This Guarantee applies to all product purchased from an Authorised Dealer of Lumberjack within the United Kingdom. Terms of Guarantee may vary in other countries. BS228...
-
Page 21: Declaration Of Conformity
Old Heath Road, Wolverhampton, WV1 2RP. Tel: 01902 450 470 Declares that the BAND SAW (BS228) Is in compliance with the regulations included in the Directives:2006/95/EC EC DECLARATION OF CONFORMITY Certificate for EC-type examination delivered by TÜV Süd Product Service GmbH-80339 München GERMANY (Registration No.:N8M 13 08 28954 036 ) -
Page 22: Parts List
BS228 AIR6V AIR6V AIR6V... - Page 23 98.11 bolt bolt fixing nut flat washer fixing plate bolt flat washer lower protecting cover flat washer flat washer bolt bolt locking handle strain relief flat washer guide block pressure spring bolt adjustment handle BS228 AIR6V AIR6V AIR6V...
- Page 24 118.6 144.01 fence 118.7 bolt 144.02 shrapnel 118.8 flat washer 144.03 panel 118.9 bolt 144.04 pull rod limit shaft sleeve 144.05 locking handle bolt 144.06 fence seat flat washer 144.07 end cup BS228 AIR6V AIR6V AIR6V...
- Page 25 Parts List Description Description 144.08 bolt LED driver 144.09 locknut bolt 144.10 bolt LED light flat washer BS228 AIR6V AIR6V AIR6V...
-
Page 26: Parts Diagram
Parts Diagram BS228...
Need help?
Do you have a question about the BS228 and is the answer not in the manual?
Questions and answers