Wiring Diagrams; Wiring Diagrams - Single Phase - Daikin FCAG35AVEB Technical Data Manual

7

Wiring diagrams

7 - 1 Wiring Diagrams - Single Phase

FCAG-A
7
1
2
3
Outdoor
(note 3)
H05VV-U4G2.5
(Note 7)
In case of simultaneous
operation system (note 5)
1 1 1
2 2 2
3 3 3
X2M X2M X2M
Remote control
X24A
X23A
X50A
X6A X33A X70A
Position of connectors in control box
A1P Main PCB
C105 Capacitor
F1U Fuse (T, 3.15A, 250V)
DS1 Dip switch on PCB
H1P Flashing lamp (service monitor green)
K2R Magnetic relay (drain pump)
M1P Motor (drain pump)
M1F Motor (indoor fan)
M1S-M4S Motor (swing blade)
R1T Thermistor (air)
R2T, R3T Thermistor (coil)
V1R Diode bridge
X1M Terminal block (remote control)
X2M Terminal block (power supply)
Z1C, Z2C Ferrite core
Z1F
PS Power supply circuit
RC Signal receiver circuit
TC Signal transmission circuit
NE Noiseless earth
A3P, A4P Sensor kit PCB
Infrared remote control (receiver/display unit)
A5P Receiver PCB
A6P Display PCB
BS1 Push button (on/off)
H1P Pilot lamp (on: red)
1. : terminal block,
2. In case of simultaneous operation indoor unit system, see the indoor unit wiring only.
3. For details, see wiring diagram attached to the outdoor unit.
4. In case of using central remote control, connect it to the unit in accordance with the attached installation manual.
5. In case of simultaneous operation system, connected quantity of the indoor units varies according to the connected outdoor unit.
6. In case of main/sub changeover, see installation manual attached to the remote control.
7. Shown only in case of protection piping, use H07RN-F in case of no protection.
8. X35A, X39A, X70A are connected when optional accessories are being used (auto clean panel), see wiring diagram of this accessory.
9. Connect power of adapter for wiring to terminal block (X2M) of indoor unit directly.
10. Colors: BLK: Black, RED: Red, BLU: Blue, WHT: White, YLW: Yellow, GRN: Green, BRN: Brown, PPL: Purple, PNK: Pink, ORG: Orange.
12
• Indoor Unit • FCAG-A
R2T R1T
GR
S1L
t° t°
N
Indoor
Z2C
N=1
NE
X15A X18A X16A
K2R
X2M
X27A
F1U
1
BLK
Z1F
2 WH
T
3
RED
X33A
TC RC
PE
A7P
Terminal for
X1A
F1U
operation display
X2A
X1
Compressor
KHuR KC
F2U
X2 operation
Y
R
X3
KFR
C Y2
Fan operation
X4
Adapter for wiring (optional) (note 9)
A1
P
X2M
X39A
X35A
Indoor unit
Sensor kit
: connector,
• Split - Sky Air • FCAG-A
Sensor kit (optional)
A4P A3P
R3T
A2P
t°
X17A X83A X81A
V1R
C105
PS
H1P
X35A
X20A X70A
Z1C
N=1
MSW MSW
MS
M4S M3S
M1F
H2P Pilot lamp (timer: green)
H3P
H4P Pilot lamp (defrost: orange)
H5P Pilot lamp (element cleaning: red)
H6P Pilot lamp (timer: green)
DS1 Dip switch (main/sub)
DS2 Dip switch (wireless address set)
A7P Adapter PCB
F1U Fuse (5A, 250V)
F2U Fuse (5A, 250V)
KHuR Magnetic relay
KCR Magnetic relay
KFR Magnetic relay
X1A Connector (power supply for option PCB)
X2A Connector (sensor kit)
X24A Connector (infrared remote control)
X33A Connector (adapter for wiring)
X35A Connector (auto clean panel)
X39A Connector (auto clean panel)
X70A Connector (auto clean panel)
X81A Sensor kit
R1T Thermistor (air)
A2P Sensor PCB
X1M
PNK T2
Input from outside
WH T1
F2
T YLW
Central remote
F1
ORG
control (note 4)
BLU P2
P1
BL
K
A1P
X30A
X39A
A5P
OFF ON X2A
EMG.
X1A
Norm.
STB.
X24A
DS1
X36A DS1
X25A
OFF ON
DS2
OFF ON
Receiver/display unit (optional)
MS
MSW MSW M1P
M2S M1S
Adapter for wiring
Connectors for optional parts
Wired remote control
Humidity sensor
Wired remote
control
(note 6)
P
R1T
t°
N
A6P
BS1
X1A
H1P
H2P
H3P
H4P
H5P
H6P
3 109572