Page 1
Blood Pressure Monitor LS810-B Wrist Type FCC ID: OU9LS810-B01 Thank you very much for selecting TRANSTEK Blood Pressure Monitor LS810-B. GUANGDONG TRANSTEK MEDICAL ELECTRONICS CO., LTD Zone A, 5/F., Investment Building, No. 12, Huizhan East Rd., Torch Please do read the user manual carefully and thoroughly so as to ensure...
Table of Contents Table of Contents INTRODUCTION ............. 2 General Description Measurement Principle Safety Information Indications for Use LCD Display Signal Monitor Components BEFORE YOU START ............6 Power Supply and Charge Power Setting Date and Time MEASUREMENT ............. 9 Positioning the Cuff Pair up the Blood Pressure Monitor with Your Device Strat Measurement Data Management...
The design provides you with two years of reliable service. measuring blood pressure and heartbeat rate with wrist circumference ranging Reading taken by the LS810-B are equivalent to those obtained by a trained from 13.5 cm to 21.5 cm ( about 5-8.5 inches ).
Measurement unit of blood pressure IHB Detector Irregular Heartbeat Detector Bluetooth Successful Bluetooth Connection USB Interface Error Error List Recalling the history records Memory 1.Blood Pressure Monitor 2.USB Cable and AC Adaptor Hour:Minute (Month/Day/Year) (LS810-B) ( Model: UE0WCP- 0501000SPC) Time 3.User Manual...
CAUTION [HOUR]. Press “MEM” button to change the numeral. Each press 1. The battery of LS810-B is built-in rechargeable lithium-ion battery, will increase the numeral by one please do not disassemble it by the unauthorized maintenance personel. in a cycling manner.
BEFORE YOU START MEASUREMENT Positioning the Cuff 4.Repeat step 2 and 3 to confirm 1.Remove all accessories (watch, bracelet, etc) from your left wrist. If your [MINUTE]. physician has diagnosed you with poor circulation in your left wrist, use your right wrist.
MEASUREMENT MEASUREMENT Pair-up the Blood Pressure Monitor Start Measurement with Your Device 1.After correctly positioning the cuff, 1.Turn on Bluetooth and the app. press START button to turn on the Make sure both are ON when monitor, and it will complete the pair-up is proceeding.
MEASUREMENT DATA MANAGEMENT 2.This device will proceed Recall the Records to data transmission automatically after 1.Press “MEM” button to access the measurement. memory. The monitor will display the The Bluetooth symbol calculated average of the last three blinks on the LCD readings first.
INFORMATION FOR USER DATA MANAGEMENT Delete the Records Tips for Measurement It can cause inaccuracy if the measurement is taken in the following When you did not obtain the accurate measurement, you can clear all the circumstances. measuring results by following below steps. 1.Under Memory Recalling Mode, press and hold both the “MEM”...
2. If you have any problems with this device, such as setting up, maintaining or using, please when displaying the measuring result. contact with SERVICE PERSONNEL of Transtek. Don’t open or repair the device by yourself. 3. Please report to Transtek if any unexpected operation or events occur.
ABOUT BLOOD PRESSURE TROUBLESHOOTING This section includes a list of error messages and frequently Why my blood pressure asked questions for problems you may encounter with your blood is varies even in one pressure monitor. If the products not operating as you think it day? should, check here before arranging for servicing.
3.7V 420mAH Built-in rechargeable lithium-ion Power supply battery, 5V / 1A USB AC Adaptor For more information about our products, please visit www.transtek.cn.you can get customer service, usual problems and customer download, transtek Display moder Digital LCD V.A.46.5x36.5mm will serve you anytime.
The LS810-B is intended for use in the electromagnetic environment specified below. The customer of the user of the LS810-B should assure that it is used in such an environment. NOTE: This equipment has been tested and found to comply with the...
Page 14
The LS810-B is intended for use in the electromagnetic environment specified below. The customer of the user of the LS810-B should assure that it is used in such an The customer or user of LS810-B should assure that it’s used in such an environment.
Page 15
RF transmitters, an electromagnetic site survey should be communications equipment. considered. If the measured field strength in the location in which the LS810-B is used exceeds the applicable RF compliance level above, the LS810-B should Rated maximum output Separation distance according to frequency of transmitter (m) be observed to verify normal operation.
Need help?
Do you have a question about the LS810-B and is the answer not in the manual?
Questions and answers