Additional Information; Troubleshooting ················································· - Sony RMT-V501F Service Manual

QQ
3 7 63 1515 0

Additional Information

General setup information
1 Press SET UP when the DVD player is in stop
mode, then press V/v to select
(OPTION), then press ENTER.
Press V/v to select the option to change.
2
Press B/b to change the setting.
3
When changing the "RF Output Channel," confirmation messages will
appear. Press ENTER to confirm the messages.
TE
L 13942296513
110
General setup information
5
Turn on your TV and set it to the channel you selected in step 1 (3CH or 4CH).
The channel you selected in step 4 appears on the TV screen. If the channels
change when you press CH +/–, you have made the correct setting.
Whenever you use the DVD-VCR, set the TV to the channel selected in step 1.
Attaching the external antenna connector
When using a 300-ohm twin lead cable for a
VHF/UHF antenna, use an antenna connector
(not supplied) to connect the antenna to the
DVD-VCR.
1 Loosen the screws on the antenna connector.
2 Wind the twin leads around the screws on the antenna connector.
3
Retighten the screws.
Attaching a VHF/UHF band mixer
When using both a 75-ohm coaxial cable and
a 300-ohm twin lead cable for a VHF/UHF
antenna, use a VHF/UHF band separator/
mixer (not supplied) to connect the antenna
to the DVD-VCR.
1
Loosen the screws on the mixer.
www
2
Wind the twin leads around the screws on the mixer.
3 Retighten the screws.
4 Connect the 75-ohm coaxial cable to the mixer.
.
112
General setup information
http://www.xiaoyu163.com
SET UP
V/v/B/b
ENTER
Language
Clock Set/Adjust
Channel Setup
Auto Power Off
RF Output Channel
V v
ENTER
Language
Clock Set/Adjust
Channel Setup
Auto Power Off
RF Output Channel
V v B b
300-ohm twin
lead cable
Antenna
connector
(not supplied)
300-ohm twin
lead cable
75-ohm coaxial
cable
x ao u163
y
i
http://www.xiaoyu163.com
2 9
8
4
Press SET UP to exit the menu.
Menu choices
The default settings are indicated in bold print.
Menu option
Auto Power Off
RF Output Channel
Setting the RF Output channel
When connecting the DVD-VCR to the TV
using only the antenna cable, you must set
the RF Output channel in the "OPTION
SETUP" menu so that the TV can receive the
correct signal from the DVD-VCR.
OPTION SETUP
:English
[ Off ]
[3CH]
RETURN SET UP
OPTION SETUP ?/1
CHANNEL +/–
:English
1
Set the RF Output channel to "3CH" or "4CH" (see page 110 to set the channel),
[ Off ]
[3CH]
whichever channel is not used in your area. If both are used, set the switch to
either channel.
RETURN SET UP
Press ?/1 to turn on the DVD-VCR.
2
3
Press TV/VIDEO to turn on "VIDEO" in the DVD-VCR's display window.
4
Press CH +/– to display a channel number in the display window.
Select an active channel number in your area.
Q Q
3 6 7 1 3 1 5
Troubleshooting
If you have any questions or problems not covered below, please consult your nearest Sony
dealer. (For customers in USA)
General Troubleshooting
Symptom
The ?/1 switch does not function.
The power is turned on but the DVD-
VCR does not operate.
The clock has stopped and "–:–"
appears in the display window.
The remote commander does not
function.
The tracking meter does not appear
on the screen.
You cannot control other TVs.
VHF/UHF
band
separator/
mixer (not
supplied)
co
.
1-27
9 4 2 8
Set this option to
• "Off" to deactivate the Auto Power Off function.
• "1Hr"/"2Hr" to turn the DVD-VCR off automatically if no
signal is received and you do not press any of the buttons
during this time.
• "3CH" when using channel 3 to receive the VCR signal.
• "4CH" when using channel 4 to receive the VCR signal.
For details, see page 111.
?/1
CH +/–
TV
TV/VIDEO
0 5 8 2 9 9 4 2 8
General setup information
Remedy
• Connect the AC power cord securely.
• Moisture condensation has occurred. Turn the power off,
unplug the AC power cord and leave the DVD-VCR to
dry for over three hours.
• The clock stops if the DVD-VCR is disconnected from
the wall outlet. Reset the clock (and timer).
• Make sure you are pointing the remote commander at the
remote sensor on the DVD-VCR.
• Replace all the batteries in the remote commander with
new ones if they are weak.
• Make sure the TV / DVD·VIDEO switch is set correctly.
• Select correctly VIDEO or DVD with the SELECT DVD/
VIDEO button.
• The recording condition of the tape is very poor and
tracking cannot be adjusted.
• Set your TV's code number. The code number may
change when you replace the batteries of the remote
commander.
m
Troubleshooting
9 9
continued
9 9
111
continued
113