Finishing; Front Panel Removal And Installation; Intake Grille Removal; Intake Grille Installation - Fujitsu ASYG09LECB Installation Manual

8. FINISHING

(1) Insulate between pipes.
• Insulate suction and discharge pipes separately.
• For rear, right, and bottom piping, overlap the connection pipe heat insulation and
indoor unit pipe heat insulation and bind them with vinyl tape so that there is no
gap.
• For left and left rear piping, butt the connection pipe heat insulation and indoor unit
pipe heat insulation together and bind them with and vinyl tape so that there is no
gap.
• For left and left rear piping, wrap the area which accommodates the rear piping
housing section with cloth tape.
• For left and left rear piping, bind the
connection cable to the top of the pipe with
vinyl tape.
• For left and left rear piping, bundle the piping
and drain hose together by wrapping them
with cloth tape over the range within which
they fi t into the rear piping housing section.
(2) Temporarily fasten the connection cable
along the connection pipe with vinyl tape.
(Wrap to about 1/3 the width of the tape
from the bottom of the pipe so that water
does not enter.)
(3) Fasten the connection pipe to the outside
wall with a saddle, etc.
(4) Fill the gap between the outside wall pipe
hole and the pipe with sealer so that rain
water and wind cannot blow in.
(5) Fasten the drain hose to the outside wall, etc.
Saddle*
Pipe
Overlap the insulation
Connection pipe
(heat insulation)
Bind the pipes together
so that there is no gap.
Pipe
Drain hose
Left piping
Connection cable
Pipe
Drain hose
Check the following:
GOOD
Drain hose
Saddle

9. FRONT PANEL REMOVAL AND INSTALLATION

9.1. Intake grille removal

(1) Open the intake grille.
(2) Pull down the knob.
(3) Lift the intake grille upward, until the axle at the top of the intake grille is removed.

9.2. Intake grille installation

(1) The fi xing axle of the intake grille is installed on the Panel.
(2) Lay down the intake grille.
En-7
Intake grille
Knob
Intake grille
Mounting shaft
Bearing
Front panel
Outside wall cap*
Sealer putty*
(Outdoors)
*Field supplied
Wall
Indoor unit pipe
(heat insulation)
Vinyl tape
Wrap with cloth tape
Cloth tape
For connection from the left rear
Wall pipe Connection cable
Drain hose Connection pipe
PROHIBITED
Lifted up Wave End in water

9.3. Front panel removal

(1) Remove intake grille (Reference the intake grille removal.)
(2) Remove wire cover.
(3) Remove 3 screws.
Screws (3 position)
Screws (Wire cover)
Push the [▲] marks.
(4) The front panel is pulled to the front, raising the upper surface, and a front panel is
removed.

9.4. Front panel installation

(1) First, fi t the lower part of the front panel, and insert top and bottom hooks. (3 top
sides, 6 bottom sides, 2 center)
Indoor
unit
Bottom holes
(6 position)
Top holes (3 position)
Center hooks
Indoor unit
(2 position)
(2) Attach the 3 screws.
(3) Attach the wire cover.
(4) Attach the intake grille.
Install the Front panel and Intake grille securely. If installation is imperfect, the Front
panel or Intake grille may fall off and cause injury.

10. TEST RUN

Check items
(1) Is operation of each button on the remote controller normal?
(2) Does each lamp light normally?
(3) Do air fl ow direction louvers operate normally?
(4) Is the drain normal?
(5) Do not have an error noise and vibration during operation?
•
Do not operate the air conditioner in test run for a long time.
[Operation method]
• For the operation method, refer to the operating manual.
• The outdoor unit may not operate depending on the room temperature.
• In this case, press the TEST RUN button on the remote controller while the air
conditioner is running.
(Point the transmitter section of the remote controller toward the air conditioner and
press the TEST RUN button with the tip of a ballpoint pen, etc.)
Transmitter section
TEST RUN button
Wire cover
Wall hook bracket
Front panel
Bottom hooks (6 position)
Front panel
Top hooks
(3 position)
Front panel
Latches (2 position)
CAUTION