Omron 3G3MX2 Quick Start Manual page 31

MX2 Quick Start Guide
Option Terminal
Code Symbol
31 FBV PID Second Stage Output
32 NDc Network Disconnect Detect
33 LOG1 Logic Output Function 1
34 LOG2 Logic Output Function 2
35 LOG3 Logic Output Function 3
39 WAC Capacitor Life Warning Sig-
nal
40 WAF Cooling Fan Warning Signal
41 FR Starting Contact Signal
42 OHF Heat Sink Overheat Warning
43 LOC Low load detection
44 MO1 General Output 1
45 MO2 General Output 2
46 MO3 General Output 3
50 IRDY Inverter Ready Signal
51 FWR Forward Rotation
52 RVR Reverse Rotation
53 MJA Major Failure Signal
54 WCO Window Comparator for
Analog Voltage Input
55 WCOI Window Comparator for
Analog Current Input
58 FREF Frequency Command
Source
59 REF Run Command Source
60 SETM 2nd motor Selection
62 EDM STO (Safe Torque Off) Per-
formance Monitor
(Output terminal 11 only)
63 OPO Option card output
255 no Not used
In the same way of that the digital inputs is possible to choose between normally close and normally open and even is possible to
use some On and Off delay for each of the outputs.
28
Input Function Summary Table
Function Name
ON
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
Parameter Parameter name
Output [11] function
C021
[EDM assignable]
C022 Output [12] function
C026 Alarm relay function
C031 Output [11] active state
C032 Output [12] active state
C036 Alarm relay active state
C130 Output [11] on delay
C131 Output [11] off delay
C132 Output [12] on delay
C133 Output [12] off delay
C140 Relay output on delay
C141 Relay output off delay
C132 Output [12] on delay
C133 Output [12] off delay
Intelligent output
d006
terminal status
Description
Transitions to ON when the inverter is in RUN Mode and the PID Process Vari-
able (PV) is less than the Feedback Low Limit (C053)
Transitions to OFF when the PID Process Variable (PV) exceeds the PID High
Limit (C052), and transitions to OFF when the inverter goes from Run Mode to
Stop Mode
When communications watchdog timer (period specified by C077) has time out
When the Boolean operation specified by C143 has a logical "1" result
When the Boolean operation specified by C146 has a logical "1" result
When the Boolean operation specified by C149 has a logical "1" result
Lifetime of internal capacitor has expired.
Lifetime of cooling fan has expired.
Either FW or RV command is given to the inverter
No FW or RV command is given to the inverter, or both are given to the inverter
Temperature of the heat sink exceeds a specified value (C064)
Motor current is less than the specified value (C039)
General output 1 is ON (Used by Drive programing)
General output 2 is ON (Used by Drive programing)
General output 3 is ON (Used by Drive programing)
Inverter can receive a run command
Inverter is driving the motor in forward direction
Inverter is driving the motor in reverse direction
Inverter is tripping with major failure
Analog voltage input value is inside of the window comparator
Analog current input value is inside of the window comparator
Frequency command is given from the operator
Run command is given from the operator
2nd motor is being selected
STO is being performed
(output terminal for option card)
–
Description
Programmable functions available for logic
(discrete) outputs transistor type
Programmable functions available for logic
(discrete) outputs relay type
Select logic conversion, two option codes:
00... normally open [NO]
01... normally closed [NC]
Set range is 0.0 to 100.0 sec.
Set range is 0.0 to 100.0 sec.
Set range is 0.0 to 100.0 sec.
Set range is 0.0 to 100.0 sec.
ON
OFF
Relay 12 11
MX2 Quick Start Guide