Download
Share
Print this page
Graco Pack'n'Play Owner's Manual
  1. Manuals
  2. Brands
  3. Graco Manuals
  4. Baby & Toddler Furniture
  5. Pack'n Play
  6. Owner's manual

Graco Pack'n'Play Owner's Manual

Playard
Hide thumbs Also See for Pack'n'Play:

Advertisement

Quick Links

Download this manual
Read all instructions BEFORE assembly and USE of
product. KEEP INSTRUCTIONS FOR FUTURE USE.
Pack 'n Play
Playard
®
Newborn Napper
Oasis™with Soothe
®
Surround™ Technology
Owner's Manual

Advertisement

loading

Related Manuals for Graco Pack'n'Play

Summary of Contents for Graco Pack'n'Play

  • Page 1 Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE. Pack 'n Play Playard ® Newborn Napper Oasis™with Soothe ® Surround™ Technology Owner’s Manual...
  • Page 2 Failure to follow these warnings and the instructions could result in serious injury or death. Setting Up the Playard • THIS PRODUCT REQUIRES ADULT ASSEMBLY. • Keep fingers clear of top corners during setup. Be sure playard is completely set up before use. Check that the four top rails are completely latched, the center of the floor is pushed down, the mattress/pad is flat, the straps are securely fastened to the bottom of the unit.
  • Page 3 • On soft bedding. NEVER add a mattress, pillow, comforter or padding. Use ONLY mattress pad provided by Graco. • To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless otherwise advised by your physician.
  • Page 4 Avoiding Strangulation Hazards • Strings and cords can cause strangulation. Keep strings and cords away from child. • NEVER place the playard near a window where cords from blinds or drapes can strangle a child. • NEVER hang strings on or over the playard. •...

  • Page 5: Parts List

    Parts list This model may not include some features shown below. Check that you have all the parts for this model BEFORE assembling your product. If any parts are missing, call Customer Service. Tools required: Phillips Screwdriver ALL MODELS...
  • Page 6 Setup Disconnect straps holding mattress around playard. Pull up on side rails in middle above push button until all four sides are locked. DO NOT push center down yet. SNAP! SNAP!
  • Page 7 SNAP! • When setting up, lock rails BEFORE lowering center. Be sure top rails have become rigid. If not, pull up again until they are rigid. If top rails do not latch, lift the center of the floor higher. Hold one end of the unit up and push the center of the floor down.
  • Page 8 Always use mattress/pad soft side up. Put two tabs under mattress/pad through button holes and fasten securely on bottom of unit.
  • Page 9 Pull strap through bottom of playard SNAP! and wrap around tube and refasten snap. Repeat on other corners. To Fold Release snap straps and hook and loop straps on bottom of playard. Pull mattress fully out of playard. DO NOT unlock top rails yet. Center of floor must be halfway up before top rails will unlock.
  • Page 10 Center of floor must be up. 1. Lift up slightly on the top rail. 2. Push in on the button located on the side of the top rail to release the two tubes. 3. Push down. • If top rails do not unlatch, DO NOT FORCE.
  • Page 11 Do not force. If unit will not fold, look for a partially latched top rail. Squeeze the latch button to release the rail.
  • Page 12 To Cover Cover unit with handle out. Zip together.
  • Page 13 • If a sheet is used with the pad use only the one provided by Graco or one specifically designed to fit the dimensions of the bassinet. • Never place child in bassinet while napper is attached.
  • Page 15 You will need to remove the mattress/pad from the bottom of the playard to use inside your bassinet. Insert tubes on short end of bassinet into the corners of playard. Attach 4 bassinet clips to the long sides of playard. Openings NOTE: Napper mount should always be attached on the end...
  • Page 16 Insert tapered end of bar into end of other bar with hole in it. Repeat with other set of bars. CHECK: Tubes MUST be assembled before placing mattress/pad in bassinet. Open the battery compartment lid by inserting a screwdriver the slot. Insert one D-(LR20) cell battery (not included).
  • Page 17 Cord in bottom of bassinet. Vibration must be fastened tight and centered on the webbing strap to work properly.
  • Page 18 Remove screw from back of electronics module. Remove battery door and insert 3 AA (LR06) batteries (not included). Replace door and screws.
  • Page 19 Insert end of cord into side of electronic module. Attach electronic module to playard as shown. SNAP! Insert the mattress/pad soft side up into the playard, making sure the hook and loop patches on bottom of mattress attaches to matching hook and loop patches on the bassinet.
  • Page 20 For Safe Battery Use Keep the batteries out of children’s reach. Any battery may leak battery acid if mixed with a different battery type, if inserted incorrectly (put in backwards) or if all batteries are not replaced or recharged at the same time. Do not mix old and new batteries.
  • Page 21 WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • Page 22 Using Electronics Module The vibration unit may ONLY be used with the bassinet or napper. WARNING You must remove the module from the unit when your child can pull up to a standing position. Remove screw from back of electronics module. Remove battery door and insert 3 AA (LR06) batteries (not included).

  • Page 23: Power Button

    WAVES PLAYFUL ENVIRONMENT ENVIRONMENT ENVIRONMENT TWINKLE TWINKLE SELECTION LULLABY ENVIRONMENT BUTTONS ENVIRONMENT RAINDROPS STROLLER RIDE ENVIRONMENT ENVIRONMENT BELLS HEART BEAT ENVIRONMENT ENVIRONMENT CAR RIDE WIND ENVIRONMENT ENVIRONMENT VOLUME BUTTON LIGHT BUTTON VIBE BUTTONS TIMER BUTTON POWER BUTTON POWER BUTTON— Press once to turn all functions on/off.
  • Page 24 LIGHT BUTTON— Press once for light, twice to increased brighness, and three times to increase brightness again. Press a fourth time to turn light off. VOLUME BUTTON— Press top portion of button to increase volume and bottom portion of button to decrease volume.
  • Page 25 FOR ALL ENVIRONMENTS— To turn vibe off, but keep sound, press vibe off button. To turn sound off and keep vibe on, press volume down until it is off. ENVIRONMENT SELECTION BUTTONS— Press left or right button to choose desired environment. CAR RIDE ENVIRONMENT—...
  • Page 26 PLAYFUL ENVIRONMENT— Select for playful song with synchronized vibration. WAVES ENVIRONMENT— Select for waves sound with synchronized vibration. TWINKLE TWINKLE ENVIRONMENT— Select for additional lullaby sound with synchronized vibration. RAINDROPS ENVIRONMENT— Select for rain sound with synchronized vibration. BELLS ENVIRONMENT— Select for bells sound with synchronized vibration.

  • Page 27: Changing Table

    • Always stay within arm’s reach of your child when using the changing table. Never leave child unattended. • The changing table is designed for use only with this Graco playard. Do not use on the floor, bed, counter or other surfaces.
  • Page 28 Bottom of Changer Slide tube through fabric as Fondo del cambiador shown. Repeat with other tube. While changer fabric is still facing down, slide changer tube into other channel in fabric as shown. Tubes should appear exactly as shown.
  • Page 29 Slide changer stand onto leg tubes with hold on side facing out as shown. Snap leg tubes together as shown. SNAP! Slide changer stand over tube joint until it snaps into place. SNAP! SNAP! Attach short tubes into changing table mounts. SNAP!
  • Page 30 Insert changer connector tubes into openings in corners of playard. SNAP! SNAP! To remove, push down on the changing table and press in button. With button depressed, pull up corner of changing table. Repeat for other side.
  • Page 31 Soothing Cocoon™ Napper WARNING Prevent serious injury or death: Failure to follow these warnings and the instructions could result in serious injury or death. • You are responsible to provide adult supervision when using your napper. • Napper must be properly attached to bassinet before use. FALL HAZARD: To prevent falls, stop using the product when infant: •...
  • Page 32 WARNING • To prevent serious injury or death, DO NOT REMOVE FOAM. • Remove and IMMEDIATELY discard the zip tie. Ziptie Remove mattress pad from bassinet.
  • Page 33 Unfasten the webbing strap holding the vibration in the playard. Unplug the vibration unit and remove from bassinet. Insert mattress pad into bassinet.
  • Page 34 Place napper upside down on a flat surface with the vibration unit pocket facing up. Locate the vibration unit pocket on the under side of the napper. Open pocket by pulling on the hook and loop tape as shown.
  • Page 35 Plug-in one end of the short cord into the side of the vibration unit as shown. Insert vibration unit into pocket. Close pocket by re-attaching hook and loop tape as shown.
  • Page 36 Insert the body support strap through the slot in the napper. MAKE sure strap is not twisted. Secure hook and loop tape as shown.
  • Page 37 Canopy • Capota WARNING • Always attach all provided fasteners (strings, straps, clamps, etc.) tightly to playard according to these instructions. Check frequently. • Do not add additional strings or straps to attach to any other crib or playpen. Wrap canopy around head end of seat and secure hook and loop tape on both sides of napper.
  • Page 38 Insert mattress pad into bassinet. NOTE: Seat should always be attached opposite the changing table. SNAP! Latch the “C” clip on head end of napper over center of the bassinet clip and foot end of napper to mount on bassinet clip as shown. SNAP! Make sure both sides of the seat are securely latched to the...
  • Page 39 Find short cord connected to vibration unit under napper pad. Plug in the short cord coming out of the napper pocket into the electronic module attached to the playard. Attach electronic module at foot end of napper as shown. Make sure the light faces into playard.
  • Page 40 To Remove Napper To remove, pull up on napper.

  • Page 41: Parent Organizer

    Parent Organizer WARNING Always keep objects out of child’s reach. Remove this accessory when child is able to pull himself up in the playard.

  • Page 42: Care And Maintenance

    Care and Maintenance FROM TIME TO TIME CHECK YOUR PLAYARD for worn parts, torn material or stitching. Replace or repair the parts as needed. Use only Graco replacement parts. ® IF PLAYARD IS USED AT THE BEACH, you MUST clean sand off your playard, including the feet, before packing it into cover.

This manual is also suitable for:

Newborn napper oasis with soothe surround technology