Advertisement
RECHARGEABLE 2.4GHz - DX-2 STUNT DRONE
OPERATING DRONE
Step 1 – Pre-Flight Checklist
1. Read all warnings and instructions
2. Install remote batteries, page 2
3. Make sure that drone and remote are
powered off
4. Install Blade Guards Drone, page 6.
5. Charge batteries, page 3.
Step 2 – Choosing a location
• Drone is designed to be flown/driven indoors
and outdoors
• Always make sure you have enough space to
fly drone
• Always follow warnings, page 1.
Step 3 – Driving Mode
1. Making sure your remote is off, slide drone
switch to ON. Drone lights will begin to flicker
2. Choose a flat even surface and follow the
diagram
3. Turn remote on. Bring the Throttle all the way
up then bring it all the way down. Remote will
beep and drone lights will flicker rapidly then
turn on permanently once paired.
4. Drone is ready for flight.
Printed in China.
Step 4 – Lift Off
1. Slowly and carefully bring the throttle up.
Step 5 – Drone Begins to Drift
Follow this step if your drone begins to drift
• Drone drifts backwards: Slide the
• Drone drifts forwards: Slide the
• Drone drifts left: Slide the Side to Side
• Drone drifts right: Slide the Side to Side
• Drone spins clockwise (viewing drone from
• Drone spins counter-clockwise (viewing drone
Always turn off remote prior to retrieving
Step 6 – Operating Drone in Flight
The drones range is approximately 150 feet
5 FEET
• Read and be aware of all warnings found on
• Maintain your desired elevation by using the
• Use the Throttle joystick in a circle motion to
• Use the Multi Directional Joystick to move
• Review step 5 if your drone begins to drift
Propellers will begin to spin and drone will
begin to elevate. You can compensate for
some of the drones drifting by using the Multi
Directional Button or by following step 5. You
may need to practice this step several times
before successfully getting drone into the air.
while take off or during flight
Forward/Backwards Adjustment up
Forward/Backwards Adjustment down
Adjustment to the right.
Adjustment to the left.
top): Slide the Spin Adjustment to the left
from top): Slide the Spin Adjustment to the
right.
or picking up drone. This will help you
avoid accidently activating propellers.
page 1.
Throttle
spin the drone
forwards, backwards, and side to side
5
Advertisement
Need help?
Do you have a question about the DX-2 and is the answer not in the manual?
Questions and answers
When the switch on drone is off, the lights on drone are blinking.. Not sure what to do? Is the drone no good? Broke in some way?
The blinking lights on the Sharper Image DX-2 drone, even when the power switch is off, could indicate an internal electrical issue. The drone may have suffered damage from the reported bump on the ceiling, potentially affecting its circuitry or power switch. This could cause residual power to keep the lights flashing. Additionally, if the drone no longer pairs with the remote, it suggests a malfunction that may require inspection or repair.
This answer is automatically generated
como cambiar las hélices del dron
To change the propellers on the Sharper Image DX-2 drone:
1. Identify the Blades: Each propeller has a number written on it. Match the new blades with the corresponding numbered positions on the drone.
2. Remove the Damaged Propeller: Carefully pull the old propeller straight up to remove it.
3. Install the New Propeller: Align the new propeller with the post and push it straight down until you hear a small click.
4. Check for Proper Installation: Ensure the propellers are securely attached and match the correct positions before flying.
This answer is automatically generated
Can I use my, smartphone to control the drone
Yes, the Sharper Image DX-2 drone can be controlled using an Android smartphone by downloading and syncing a mobile app with the drone.
This answer is automatically generated
My drone is not connecting to the remote. I'm pushing the throttle up and then down, but it is not beeping or pairing.
To fix the connection issue between your Sharper Image DX-2 drone and its remote:
1. Ensure both the drone and remote have fully charged or new batteries.
2. Turn the drone on and place it on a flat, level surface.
3. Turn on the remote.
4. Move the left joystick down, then up, then down again.
5. Wait for a beep to confirm successful pairing.
If pairing fails after following this process and the batteries are good, inspect for any loose or damaged wires inside the drone, especially near the motors or the circuit board, as a previously repaired wire could have come loose again.
This answer is automatically generated