Advertisement
RECHARGEABLE 2.4GHz - DX-2 STUNT DRONE
CONTENTS
DX-2 Stunt Drone
SPIN
DIRECTION
TRIM
TRIM
Drone Controller
Blade Guards &
4 Screws
Printed in China.
USB Connector
Replacement
Propellors
REMOTE BATTERY INFORMATION
1. Slide open the remote's battery compartment.
2. Install 6"AA" batteries as shown in the
diagram above.
3. Replace and close battery compartment.
PLEASE RECYCLE OR DISPOSE OF
ELECTRONICS PROPERLY RECYCLING
INFORMATION IS AVAILABLE AT
WWW.MERCHSOURCE.COM
LITHIUM-POLYMER BATTERY WARNING
There is a risk of fire and personal injury if Li-Po
battery is punctured, damaged or misused.
• Never expose battery to extreme temperatures
or moisture.
• Do not subject battery to strong impacts.
• Always keep battery away from flammable materials.
• Only use manufacturer specified batter(ies),
charger(s), and/or adapters, if applicable,
specified by the manufacturer.
• Battery is not serviceable.
• Let battery cool to room temperature before
charging.
• While charging, never leave battery unattended.
• Recycle or dispose of battery according to federal,
state and local laws.
• The battery is not replaceable.
KEEP THIS INSTRUCTION MANUAL FOR REFERENCE
BATTERY WARNING - ALKALINE (AA)
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.
• Insert batteries using the correct polarity. Do not short-circuit the supply terminal.
• Only use manufacturer specified batter(ies), charger(s), and/or adapters, if
applicable, specified by the manufacturer.
• Always use, replace, and recharge (if applicable) batteries under adult supervision.
2
Advertisement
Need help?
Do you have a question about the DX-2 and is the answer not in the manual?
Questions and answers
When the switch on drone is off, the lights on drone are blinking.. Not sure what to do? Is the drone no good? Broke in some way?
The blinking lights on the Sharper Image DX-2 drone, even when the power switch is off, could indicate an internal electrical issue. The drone may have suffered damage from the reported bump on the ceiling, potentially affecting its circuitry or power switch. This could cause residual power to keep the lights flashing. Additionally, if the drone no longer pairs with the remote, it suggests a malfunction that may require inspection or repair.
This answer is automatically generated
como cambiar las hélices del dron
To change the propellers on the Sharper Image DX-2 drone:
1. Identify the Blades: Each propeller has a number written on it. Match the new blades with the corresponding numbered positions on the drone.
2. Remove the Damaged Propeller: Carefully pull the old propeller straight up to remove it.
3. Install the New Propeller: Align the new propeller with the post and push it straight down until you hear a small click.
4. Check for Proper Installation: Ensure the propellers are securely attached and match the correct positions before flying.
This answer is automatically generated
Can I use my, smartphone to control the drone
Yes, the Sharper Image DX-2 drone can be controlled using an Android smartphone by downloading and syncing a mobile app with the drone.
This answer is automatically generated
My drone is not connecting to the remote. I'm pushing the throttle up and then down, but it is not beeping or pairing.
To fix the connection issue between your Sharper Image DX-2 drone and its remote:
1. Ensure both the drone and remote have fully charged or new batteries.
2. Turn the drone on and place it on a flat, level surface.
3. Turn on the remote.
4. Move the left joystick down, then up, then down again.
5. Wait for a beep to confirm successful pairing.
If pairing fails after following this process and the batteries are good, inspect for any loose or damaged wires inside the drone, especially near the motors or the circuit board, as a previously repaired wire could have come loose again.
This answer is automatically generated