RECHARGEABLE 2.4GHz - DX-2 STUNT DRONE
Getting to Know Your Drone
PLEASE READ ALL WARNINGS AND
INSTRUCTIONS PRIOR TO USE. KEEP THIS
DOCUMENT AS IT CONTAINS IMPORTANT
INFORMATION ABOUT YOUR DRONE.
1. PREPARE FOR FLIGHT
• Drone must be charged before each use (Cable included)
• Indicator light will turn off once fully charged
• Install batteries in remote
2. PAIR YOUR DRONE
Before each flight pair the remote with the drone:
1. Turn your drone on and place on a flat, level surface
2. Turn on the remote on and move the left joystick down, then up, then down again
3. The beep will indicate successful pairing
3. DIRECTIONAL LIGHTS
1. Turn your drone on and place on a flat, level surface
2. Turn on the remote on and move the left joystick down, then up, then down again
3. The beep will indicate successful pairing
4. REMOTE CONTROL OVERVIEW
Practice flying your drone below 10 feet and at low speeds until comfortable with all controls to
avoid unnecessary damage or injury
•
Left joystick:
• Up/Down controls elevation
• Left/Right controls spin
•
Right joystick: controls flight direction
•
Direction Trim: use to eliminate drift
To cut power to drone, move left joystick to down position
QUESTIONS OR CONCERNS?
PLEASE GIVE US A CALL ... WE'RE HERE TO HELP
CUSTOMER SERVICE
(800) 374-2744
Before calling please locate the 10-digit
code printed on the back of your remote
©2017 MerchSource, LLC. All rights reserved.
Distributed by MerchSource, LLC, Irvine, CA 92618.
For technical support, please visit www.merchsource.com or call
1-800-374-2744.
The artwork and design of this manual are protected by US copyright law
and may not be reproduced, distributed, displayed, published or used for
any purpose without prior written permission. It is not permitted to alter,
remove or reproduce any trademarks or copyright notice from this
manual.
Printed in China.
ADULT ASSEMBLY, CHARGING, AND
BATTERY INSTALLATION IS REQUIRED.
ADULT SUPERVISION IS REQUIRED.
CHOKING HAZARD -
Not for Children under 3 years.
KEEP THIS INSTRUCTION MANUAL AS IT CONTAINS IMPORTANT
INFORMATION FOR FUTURE REFERENCE.
Due to continuous product improvements, the picture on the manual may
differ slightly from the actual product.
PATENT PENDING
12+
WARNING:
Small Parts.
Need help?
Do you have a question about the DX-2 and is the answer not in the manual?
Questions and answers
When the switch on drone is off, the lights on drone are blinking.. Not sure what to do? Is the drone no good? Broke in some way?
The blinking lights on the Sharper Image DX-2 drone, even when the power switch is off, could indicate an internal electrical issue. The drone may have suffered damage from the reported bump on the ceiling, potentially affecting its circuitry or power switch. This could cause residual power to keep the lights flashing. Additionally, if the drone no longer pairs with the remote, it suggests a malfunction that may require inspection or repair.
This answer is automatically generated
como cambiar las hélices del dron
To change the propellers on the Sharper Image DX-2 drone:
1. Identify the Blades: Each propeller has a number written on it. Match the new blades with the corresponding numbered positions on the drone.
2. Remove the Damaged Propeller: Carefully pull the old propeller straight up to remove it.
3. Install the New Propeller: Align the new propeller with the post and push it straight down until you hear a small click.
4. Check for Proper Installation: Ensure the propellers are securely attached and match the correct positions before flying.
This answer is automatically generated
Can I use my, smartphone to control the drone
Yes, the Sharper Image DX-2 drone can be controlled using an Android smartphone by downloading and syncing a mobile app with the drone.
This answer is automatically generated
My drone is not connecting to the remote. I'm pushing the throttle up and then down, but it is not beeping or pairing.
To fix the connection issue between your Sharper Image DX-2 drone and its remote:
1. Ensure both the drone and remote have fully charged or new batteries.
2. Turn the drone on and place it on a flat, level surface.
3. Turn on the remote.
4. Move the left joystick down, then up, then down again.
5. Wait for a beep to confirm successful pairing.
If pairing fails after following this process and the batteries are good, inspect for any loose or damaged wires inside the drone, especially near the motors or the circuit board, as a previously repaired wire could have come loose again.
This answer is automatically generated