Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for KBC ESML6-FL2-M2
Summary of Contents for KBC ESML6-FL2-M2
-
Page 1: User Manual
Ethernet Switch ESML6-FL2-M2 ESML6-FL2-S2 User Manual... -
Page 2: Table Of Contents
Figure 4.1 ESML6-FL2 Typical System Application ............14 5 NETWORKING & CONFIGURATIONS ........15 6 DIMENSIONS..............17 7 WARRANTY..............18 ................18 ARRANTY NFORMATION A ITE..................... 19 LASS FCC ....................... 19 8 INSTRUCTION OF DISASSEMBLY.......... 19 Inst_manual_hw-ESML6-FL2-Rev_1010 Copyright © KBC Networks Ltd. Page 2 of 20 www.kbcnetworks.com... -
Page 3: Overview
Ethernet Switch User Manual 1 Overview 1.1 Introduction This manual covers the ESML6-FL2 series. The KBC ESML6-FL2 products are high performance, managed, eight-port industrial Ethernet switches designed for use in a wide range of operating temperatures in non-environmentally conditioned, industrial applications. -
Page 4: Technical Specification
Input power consumption <6W Over-current protection Built in Environmental Operating temperature -40°C ~ 75°C Storage temperature -45°C ~ 85°C Relative humidity 0% ~ 95% Non-condensing Mean Time Between Failure >300,000 hours Inst_manual_hw-ESML6-FL2-Rev_1010 Copyright © KBC Networks Ltd. Page 4 of 20 www.kbcnetworks.com... -
Page 5: Installation
Products are available in either DIN rail or wall-mount packages, with the following configurations: Product Type DIN Rail Wall-mount Multimode Singlemode ESML6-FL1-M2 ESML6-FL1-S2 Inst_manual_hw-ESML6-FL2-Rev_1010 Copyright © KBC Networks Ltd. Page 5 of 20 www.kbcnetworks.com... -
Page 6: Physical Connections
Ethernet Switch User Manual 2.3 Physical Connections LINK/ACT 10/100M LINK/ACT ESML6-FL2 Inst_manual_hw-ESML6-FL2-Rev_1010 Copyright © KBC Networks Ltd. Page 6 of 20 www.kbcnetworks.com... -
Page 7: Installation Method
Insert the male power block (attached to the supplied in-line PSU) to the female power socket on the device and tighten the terminal locking screws using the flathead screw driver provided. See Section 2.8 for LED status. Inst_manual_hw-ESML6-FL2-Rev_1010 Copyright © KBC Networks Ltd. Page 7 of 20 www.kbcnetworks.com... -
Page 8: Ethernet Rj45 Connections
The two pairs of uplink redundant fiber ports can be used to form a fiber optic redundant ring network. If a system failure occurs, the redundant recovery time of the ring network is less than 100ms. Inst_manual_hw-ESML6-FL2-Rev_1010 Copyright © KBC Networks Ltd. Page 8 of 20 www.kbcnetworks.com... -
Page 9: Grounding / Earthing
The cross-section of grounding wire should not be less than 2.5mm Inst_manual_hw-ESML6-FL2-Rev_1010 Copyright © KBC Networks Ltd. Page 9 of 20 www.kbcnetworks.com... -
Page 10: Dip Switch Setting
Ports 1,2 are set as redundant and master Ports 4,8 are set as redundant and master Ports 1,2 are set as redundant and master Figure 2.2 DIP Switch Settings for Selection of Uplink Mode Inst_manual_hw-ESML6-FL2-Rev_1010 Copyright © KBC Networks Ltd. Page 10 of 20 www.kbcnetworks.com... -
Page 11: Led Status
Effective network connection has been established for the port LINK/ACT FLASH Data traffic is passing through the port (Green) No effective network connection has been established for the port Inst_manual_hw-ESML6-FL2-Rev_1010 Copyright © KBC Networks Ltd. Page 11 of 20 www.kbcnetworks.com... -
Page 12: Power Input Terminals
The maximum voltage this terminal can be connected to is 350Vdc and maximum current is 120mA (see the diagram below for an example of this kind of set up). Figure 2.4 Alarm Lamp and Relay Output Inst_manual_hw-ESML6-FL2-Rev_1010 Copyright © KBC Networks Ltd. Page 12 of 20 www.kbcnetworks.com... -
Page 13: Rs232 Console Interface
LINK/ACT LED will flash to show data transfer and the yellow 10M/100M will either be off to show 10Mbps (10BASE-T) operation or on to show 100Mbps (100BASE-TX) operation. Testing PC Testing PC Figure: 3.1 Testing TP Ports Inst_manual_hw-ESML6-FL2-Rev_1010 Copyright © KBC Networks Ltd. Page 13 of 20 www.kbcnetworks.com... -
Page 14: Fiber Port Testing
Testing PC Testing PC Figure 3.2 Fiber Port Testing 4 System Examples Figure 4.1 ESML6-FL2 Typical System Application Inst_manual_hw-ESML6-FL2-Rev_1010 Copyright © KBC Networks Ltd. Page 14 of 20 www.kbcnetworks.com... -
Page 15: Networking & Configurations
100ms. A typical redundant ring set up is shown in Figure 5.1 below. Master Slave Slave Slave Figure 5.1 Typical Ring Topology Inst_manual_hw-ESML6-FL2-Rev_1010 Copyright © KBC Networks Ltd. Page 15 of 20 www.kbcnetworks.com... - Page 16 To form a redundant ring network it is recommended to use ports 4 & 8, connected as shown below in Figure 5.3. Port4 Port8 Port4 Port4 Port8 Port4 Port8 Port8 Figure 5.3 Redundant Ring Configuration Inst_manual_hw-ESML6-FL2-Rev_1010 Copyright © KBC Networks Ltd. Page 16 of 20 www.kbcnetworks.com...
-
Page 17: Dimensions
Ethernet Switch User Manual 6 Dimensions (mm) Wall Mount: Inst_manual_hw-ESML6-FL2-Rev_1010 Copyright © KBC Networks Ltd. Page 17 of 20 www.kbcnetworks.com... -
Page 18: Warranty
KBC, to be defective in material or workmanship, KBC will repair or replace such part or portion at KBC’s option. The warranty period on the repaired or replaced part or portion of this product shall be limited to the unexpired term of the original warranty. -
Page 19: Classa Ite
2. Remove cover plate. 3. Remove tightening screws for printed circuit board (PCB). 4. Take out all PCBs. Notice: When a product reaches the end of its life – return to KBC. Inst_manual_hw-ESML6-FL2-Rev_1010 Copyright © KBC Networks Ltd. Page 19 of 20... - Page 20 KBC Networks, Ltd. 25691 Atlantic Ocean Drive Suite 3B Lake Forest, CA 92630 U.S.A Americas Phone: 1-949-297-4930 Fax: 1-949-297-4933 KBC Networks Ltd., EMEA KBC Networks Ltd. Barham Court Teston, Maidstone Kent, ME18 5BZ United Kingdom Phone: +44(0)1622 618787 Fax: +44(0)20 7100 8147 Email: info@kbcnetworks.com...
Need help?
Do you have a question about the ESML6-FL2-M2 and is the answer not in the manual?
Questions and answers