Page 3 Macrovision Corporation, and is intended for home or other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineer- ing or disassembly is prohibited. Intel, Celeron, and Intel Core are trademarks/registered trademarks of Intel Corporation.
Page 4: Fcc Statement
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 5: Fcc Rf Radiation Exposure Statement
Preface FCC RF Radiation Exposure Statement: This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Page 6: Important Safety Instructions
This product is intended to be supplied by a Listed Power Unit with an AC Input of 100 - 240V, 50 - 60Hz, DC Output of 19V, 3.42A (65 Watts)/18.5V, 3.5A (65 Watts) minimum AC/DC Adapter for Model A & B computers, OR 19V, 4.74A (90 Watts) minimum AC/DC Adapter for Model C &...
Page 7: Instructions For Care And Operation
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer Do not place it on an unstable Do not place anything heavy...
Page 8 Preface Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work.
Page 9: Power Safety
Preface Power Safety The computer has specific power requirements: • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, Power Safety Warning consult your service representative or local power company.
Page 10: Battery Precautions
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Page 11: Cleaning
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock.
Page 12: Travel Considerations
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched.
Page 13 Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common.
Page 14 Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints.
Page 15: Lcd Screen Care
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. • Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. •...
Page 16 Preface...
Page 17: Table Of Contents
Preface Contents Notice .................I Keyboard ..............1-11 FCC Statement .............II Function/Hot Key Indicators ........1-12 FCC RF Radiation Exposure Statement: ....III System Map: Front & Left Views ........1-13 Instructions for Care and Operation ......V System Map: Right & Rear Views ......1-14 Power Safety .............VII System Map: Bottom View ..........1-16 Battery Precautions ..........
Page 18 Preface USB Printer ..............2-10 Drivers & Utilities Parallel Printer ............2-10 What to Install ..............4-1 Module Driver Installation ..........4-1 Power Management Driver Installation ............4-2 Overview ................3-1 Updating/Reinstalling Individual Drivers ....4-4 The Power Sources ............3-2 User Account Control (Win Vista) ......4-4 AC/DC Adapter ............3-2 Windows Security Message .........4-4 Battery .................3-2 New Hardware Found ..........4-4...
Page 19 Preface Failing the POST ............5-3 Boot Menu ..............5-12 Fatal Errors ..............5-3 Exit Menu ..............5-13 Non-Fatal Errors ............5-3 Upgrading The Computer The Setup Program ............5-4 Entering Setup .............5-4 Overview ................6-1 Setup Screens ...............5-5 When Not to Upgrade ..........6-2 Main Menu ..............5-6 Removing the Battery ............6-3 System Time &...
Page 20 Preface Short Messaging Service ..........7-27 NVIDIA Video Driver Controls Fingerprint Reader Module ..........7-28 NVIDIA Video Driver Installation ....... C-1 Fingerprint Reader Driver Installation .....7-28 NVIDIA Control Panel ..........C-2 User Enrollment ............7-29 Attaching Other Displays ..........C-5 Display Modes .............. C-7 Troubleshooting Overview ................8-1 Specifications...
Page 21 Preface Dimensions ..............D-6 System Power Options..........E- 22 & Weight ..............D-6 Hibernate Mode vs. Shutdown ......... E-22 Optional ................ D-6 Stand by Mode vs. Hibernate Mode ......E-22 Windows XP Information Configuring the Power Button........E- 24 Battery Information............. E- 25 DVD Regional Codes ...........
Page 22 Preface...
Page 23: Quick Start Guide
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: •...
Page 24: Advanced Users
Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - “BIOS Utilities” on page 5 - 1 “Upgrading The Computer”...
Page 25: Not Included
Quick Start Guide Not Included Operating Systems (e.g. Windows Vista/Windows XP) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers &...
Page 26: Model Differences
Hot-Key buttons may appear slightly different from those illustrated in this manual, however all the ports, components and functions etc. are the same for each design style. The models differ as indicated in the table below. Feature Model A Model B Model C Model D...
Page 27: System Software
Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the following operating systems are sup- ported.
Page 28: System Startup
Quick Start Guide System Startup Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
Page 29: System Map: Lcd Panel Open - Models A & C
Quick Start Guide System Map: LCD Panel Open - Models A & C Figure 1 - 2 LCD Panel Open (Model A & C Computers) Wireless Device Operation Aboard Aircraft Built-In PC Camera (Optional) The use of any portable electronic trans- mission devices aboard aircraft is usually prohibited.
Page 30: System Map: Lcd Panel Open - Models B & D
Quick Start Guide System Map: LCD Panel Open - Models B & D Figure 1 - 3 LCD Panel Open (Model B & D Computers) Wireless Device Operation Aboard Aircraft Built-In PC Camera The use of any portable electronic trans- (Optional) mission devices aboard aircraft is usually prohibited.
Page 31: Led Indicators
Quick Start Guide LED Indicators Icon Color Description The LED indicators on the computer display helpful Orange DC Power is Plugged In information about the current status of the computer. Green The Computer is On Icon Color Description The Computer is in Sleep Blinking Green Mode Green...
Page 32: Hot Key Buttons
Quick Start Guide Hot Key Buttons These buttons give instant access to the default Internet browser and e-mail program, and allow you to toggle the Silent Mode on/off with one quick button press. Hot Key Function Activate the Default E-Mail Browser Activate the Default Internet Program Toggle *Silent Mode (for power saving) Table 1 - 5 - Hot Key Buttons...
Page 33: Keyboard
Quick Start Guide Keyboard The keyboard has a numerical keypad for easy numeric data input, and features func- Other Keyboards tion keys to allow you to change operational features instantly. See Table 1 - 6, on page 1 - 12 for full function key combination details.
Page 34: Function/Hot Key Indicators
Quick Start Guide Function/Hot Key Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key utility is installed (see “Hot Key”...
Page 35: System Map: Front & Left Views
Quick Start Guide System Map: Front & Left Views Figure 1 - 5 Front & Left Views LED Indicators DC-In Jack External Monitor Port RJ-45 LAN Jack Vent/Fan Intake/ Outlet 2 * USB 2.0 Ports ExpressCard Slot (see page 7-in-1 Card Reader 7-in-1 Card Reader The card reader allows you to use the most popular digital storage card formats: MMC (MultiMedia Card) / SD (Secure Digital) / MS (Memory Stick) /...
Page 36: System Map: Right & Rear Views
Quick Start Guide System Map: Right & Rear Views Figure 1 - 6 Right & Rear Views S/PDIF-Out Jack Microphone-In Jack Headphone-Out Jack USB 2.0 Port Optical Device Drive Bay (for CD/ DVD Device - see page RJ-11 Phone Jack Security Lock Slot Battery 1 - 14 System Map: Right &...
Page 37 Quick Start Guide Disk Eject Warning Changing DVD Regional Codes Don’t try to eject a CD/DVD while the system is ac- Go to the Control Panel and double-click Device cessing it. This may cause the system to “crash”. Stop Manager (Hardware and Sound), then click the + the disk first then eject it, or press the stop button next to DVD/CD-ROM drives.
Page 38: System Map: Bottom View
Always completely discharge, then fully Cover charge, a new battery before using it. Com- RAM & CPU Bay Model A & C pletely discharge and charge the battery at Cover Computers least once every 30 days or after about 20 Vent/Fan Intake/ partial discharges.
Page 39: Windows Vista Start Menu & Control Panel
Quick Start Guide Windows Vista Start Menu & Control Panel Most of the control panels, utilities and programs within Windows Vista (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop.
Page 40: Video Features
Quick Start Guide Video Features This computer features two different (either SiS for Model A & B computers or NVIDIA for Models C & D computers) video options. You can switch display devices, and configure display options, from the Display Set- tings control panel (in Personalization) in Windows Vista.
Page 41: Display Settings & Video Control Panel/Center
Quick Start Guide Display Settings & Video Control Panel/Center Figure 1 - 9 - Display Settings & Video Control Panel/Center Video Features 1 - 19...
Page 42: Power Options
Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 17) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu.
Page 43: Features & Components
Features & Components Chapter 2: Features & Components Overview Read this chapter to learn more about the following main features and components of the computer: • Hard Disk Drive • Optical (CD/DVD) Device • 7-in-1 Card Reader • ExpressCard Slot •...
Page 44: Hard Disk Drive
Features & Components Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be Power Safety taken out to accommodate other 2.5" serial (SATA) hard disk drives (see “Storage” on page D - 3) with a height of 9.5 mm.
Page 45: Optical (Cd/Dvd) Device
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual de- Sound Volume vice will depend on the module you purchased (see “Storage” on page D - 3). The Adjustment optical device is usually labeled “Drive D:”...
Page 46: Handling Cds Or Dvds
Features & Components Handling CDs or DVDs Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be CD Emergency Eject accessed. If you need to manually eject a CD (e.g.
Page 47: Dvd Regional Codes
Features & Components DVD Regional Codes To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - DVD Regional Coding Table 2 - 1 Region Geographical Location DVD Regional Coding USA, Canada Western Europe, Japan, South Africa, Middle East &...
Page 48: 7-In-1 Card Reader
Features & Components 7-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the Card Reader Cover card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Page 49: Expresscard Slot
Features & Components ExpressCard Slot The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/ ExpressCard 34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Slot Cover Cards). Make sure you install the Card Reader driver (see “CardReader”...
Page 50: Touchpad And Buttons/Mouse
Features & Components TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to Mouse Driver your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse. If you are using an ex- ternal mouse your op- Once you have installed the TouchPad driver (see...
Page 51: Audio Features
Features & Components Audio Features You can configure the audio options on your computer from the Sound control Sound Volume panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/ Adjustment control panel (right-click the taskbar icon to bring up an audio menu).
Page 52: Adding A Printer
Features & Components Adding a Printer The most commonly used peripheral is a printer. The following conventions will Parallel Printer help you to add a printer; however it is always best to refer to the printer manual for specific instructions and configuration options. After setting up the print- er attach the parallel ca- ble to the printer.
Page 53: Power Management
Power Management Chapter 3: Power Management Overview OS Note Power management To conserve power, especially when using the battery, your computer power man- functions will vary slight- agement conserves power by controlling individual components of the computer ly depending on your (the monitor and hard disk drive) or the whole system.
Page 54: The Power Sources
Power Management The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. Attach the AC/DC adapter to the DC-in jack on the left of the computer.
Page 55: Turning On The Computer
Power Management Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press the pow- Shut Down er button on the front panel. Note that you should al- When the computer is on, you can use the power button as a Sleep/Hibernate hot- ways shut your comput- er down by choosing the key button when it is pressed for less than 4 seconds (pressing and holding the power...
Page 56: Power Plans
Power Management Power Plans The computer can be configured to conserve power by means of power plans. You Resuming can use (or modify) an existing power plan, or create a new one. Operation The settings may be adjusted to set the display to turn off after a specified time, and Table 3 - 1, on to send the computer into Sleep after a period of inactivity.
Page 57 Power Management Each Windows power plan will also adjust the processor performance of your ma- chine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose High performance for maximum performance when the computer is pow- ered from an AC power source.
Page 58: Power-Saving States
Power Management Power-Saving States You can use power-saving states to stop the computer’s operation and restart where Power Button you left off. Sleep is the default power-saving state in Windows Vista. The Power Button Earlier versions of Windows used Stand By and Hibernate as system power-saving in the Start Menu (in Classic View use the states.
Page 59: Hibernate
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a Hibernate Mode In power failure occurs the system can restore your work from the hard disk; if a power Windows Vista SP1 failure occurs when work is saved only to memory, then the work will be lost.
Page 60: Configuring The Power Buttons
Power Management Configuring the Power Buttons The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the Password computer in to a power-saving state. Protection It is recommended that you enable a password on wake up in order to protect your data.
Page 61: Resuming Operation
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo). Closing the Lid If you have chosen to Power Status To Resume Icon Color send the computer to...
Page 62: Battery Information
Power Management Battery Information Please follow these simple guidelines to get the best use out of your battery. Low Battery Warning Battery Power When the battery is criti- Your computer’s battery power is dependent upon many factors, including the pro- cally low, immediately grams you are running, and peripheral devices attached.
Page 63: Conserving Battery Power
Power Management Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. Windows Mobility Center • Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter.
Page 64: Battery Life
Power Management Battery Life Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to re- move the battery for any reason see “Removing the Battery”...
Page 65: Proper Handling Of The Battery Pack
Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode Caution • DO NOT connect the metal terminals (+, -) to each other Danger of explosion if battery is incorrectly re- placed.
Page 66: Battery Faq
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.
Page 67 Power Management Scroll down to Battery and click + to expand the battery options. Choose the options below (click Yes if a warning appears): Figure 3 - 8 Power Options Advanced Settings - Battery • Low battery levels = 0% •...
Page 68 Power Management How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Page 69: Drivers & Utilities
Drivers & Utilities Chapter 4: Drivers & Utilities What to Install This chapter deals with installing the drivers and utili- ties essential to the operation or improvement of some The Device Drivers & Utilities + User’s Manual disc of the computer’s subsystems. The system takes ad- contains the drivers and utilities necessary for the vantage of some newer hardware components for proper operation of the computer.
Page 70: Driver Installation
Drivers & Utilities Driver Installation Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in Insert the Device Drivers & Utilities + User’s Manual this order) which is the same as that listed in the disc and click Install Drivers/Option Drivers (button).
Page 71 Drivers & Utilities Manual Driver Installation Click Browse CD (button) in the Drivers Installer ap- Driver - Windows Vista with Service Pack 1 Page plication and browse to the executable file in the ap- Video Page 4 - 5 propriate driver folder. Audio Page 4 - 5 Windows Update...
Page 72: Updating/Reinstalling Individual Drivers
Drivers & Utilities Updating/Reinstalling Individual Drivers User Account Control (Win Vista) If you wish to update/reinstall individual drivers it If a User Account Control prompt appears as part of may be necessary to uninstall the original driver.To do the driver installation procedure, click Continue or this go to the Control Panel in the Windows OS and Allow, and follow the installation procedure as direct- double-click the Programs and Features icon (Pro-...
Page 73: Driver Installation Procedure
Drivers & Utilities Driver Installation Procedure Audio Insert the Device Drivers & Utilities + User’s Manual 1. Click 2.Install Audio Driver > Yes. disc and click Install Drivers (button). 2. Click Next. 3. Click Finish to restart the computer. Video 1.
Page 74: Touchpad
Drivers & Utilities TouchPad 1. Click 5.Install Touchpad Driver > Yes. 2. Click Next. Windows Update 3. Click Finish > Restart Now to restart the com- After installing all the drivers make sure you enable Win- puter. dows Update in order to get all the latest security up- dates etc.
Page 75: Optional Drivers
Drivers & Utilities Optional Drivers Bluetooth Module Note: The operating system is the default setting for See the pages indicated for the driver installation pro- Bluetooth control in Windows Vista, and does not re- cedures for any modules included in your purchase op- quire a driver.
Page 76 Drivers & Utilities 4 - 8...
Page 77: Bios Utilities
BIOS Utilities Chapter 5: BIOS Utilities Overview BIOS Settings Warning This chapter gives a brief introduction to the computer’s built-in software: Incorrect settings can cause your system to Diagnostics: The POST (Power-On Self Test) malfunction. To correct mistakes, return to Set- up and restore the Set- Configuration: The Setup utility up Defaults with <F9>.
Page 78: The Power-On Self Test (Post)
KBC/EC Firmware Revision: ******** pear slightly different. If you disable the Boot- CPU = 1 Processors Detected, Cores per Processor = 2 Intel(R) Core(TM)2 Duo CPU T5400 @ 1.50GHz time Diagnostic Screen, 1022M System RAM Passed the POST screen will not 2048 KB L2 Cache appear.
Page 79: Failing The Post
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “non- fatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible.
Page 80: The Setup Program
BIOS Utilities The Setup Program The Phoenix Setup program tells the system how to configure itself and manage ba- sic features and subsystems (e.g. port configuration). Entering Setup To enter Setup, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen on page 5 - 2 is usually present for a few seconds...
Page 81: Setup Screens
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with menu headings. When you select a Setup menus heading, a new screen appears. Scroll through the features listed on each screen to shown in this section are make changes to Setup.
Page 82: Main Menu
BIOS Utilities Main Menu PhoenixBIOS Setup Utility Figure 5 - 2 Main Main Advanced Security Boot Exit Main Menu Item Specific Help System Time: [22:12:05] System Date: [04/23/2008] IDE Channel 0 Master [Optiarc CD-RW CRX880A-(PM] <Tab>, <Shift Tab>, or SATA Port 1 [FUJITSU MHW2080BH PL-(S1)] <Enter>...
Page 83: Ide Channel 0 Master (Main Menu)
BIOS Utilities IDE Channel 0 Master (Main Menu) Pressing Enter opens the sub-menu to show the configuration of an optical Device on the computer’s IDE Channel. Use the Auto (Type:) setting to have the items con- figured automatically for you. SATA Port 1 (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a hard disk on the computer’s SATA Port 1.
Page 84: Advanced Menu
BIOS Utilities Advanced Menu PhoenixBIOS Setup Utility Main Advanced Advanced Security Boot Exit Item Specific Help Installed O/S: [VISTA] SATA Mode Selection: [AHCI] Select the operating Legacy USB Support: [Enabled] system installed Boot-time Diagnostic Screen: [Enabled] on your system which POST Beep Sound [Disabled] you will use most...
Page 85: Sata Mode Selection (Advanced Menu)
BIOS Utilities SATA Mode Selection (Advanced Menu) This menu is only available if you select the Vista O/S as your operating system. You can configure SATA (Serial ATA) control to operate in either IDE (native/ compatible) or AHCI (Advanced Host Controller Interface) modes from this menu. The SATA mode should be set to AHCI mode for this system (unless you are sure your hard disk can only operate in IDE mode).
Page 86: Security Menu
BIOS Utilities Security Menu PhoenixBIOS Setup Utility Security Menu Main Advanced Security S S e e c c u u r r i i t t y y Boot Exit Item Specific Help changes Supervisor Password Is: Clear make here affect the User Password Is: Clear Supervisor Password...
Page 87: Set User Password (Security Menu)
BIOS Utilities Set User Password (Security Menu) You can set a password for user mode access to the PhoenixBIOS Setup Utility. This will not affect access to the computer OS, (only the Setup utility) unless you Password Warning choose to set a Password on Boot (see below). Many menu items in the Phoenix- If you set a boot pass- BIOS Setup Utility cannot be modified in user mode.
Page 88: Boot Menu
BIOS Utilities Boot Menu PhoenixBIOS Setup Utility Figure 5 - 5 Main Advanced Security Boot Exit Boot Menu Item Specific Help Boot priority order: USB FDC: Keys used to view or IDE CD: Optiarc DVD RW AD-7530B-(P configure devices: IDE 4: FUJITSU MHV2100BH PL-(S1) Up and Down arrows IDE 5:...
Page 89: Exit Menu
BIOS Utilities Exit Menu Figure 5 - 6 PhoenixBIOS Setup Utility Main Advanced Security Boot Exit Exit Menu Item Specific Help Exit Saving Changes Exit Discarding Changes Exit System Setup and Load Setup Defaults save your changes to CMOS. Discard Changes Save Changes Help Select Item...
Page 90 BIOS Utilities 5 - 14...
Page 91: Upgrading The Computer
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps out- lined to make the desired upgrades. If you have any trouble or problems you can con- Warranty Warning tact your service representative for further help. Before you begin you will need: Please check with your service representative...
Page 92: When Not To Upgrade
Upgrading The Computer When Not to Upgrade These procedures involve opening the system’s case, adding and sometimes replac- ing parts. Power Safety Warning You should not perform any of these upgrades if: Before you undertake • Your system is still under warranty or a service contract upgrade proce- •...
Page 93: Removing The Battery
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons Warranty Warning it is best to remove the battery. Turn the computer off, and turn it over. Please check with your Slide the latch in the direction of the arrow.
Page 94: Upgrading The Hard Disk Drive
Upgrading The Computer Upgrading the Hard Disk Drive The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) hard HDD System disk drives with a height of 9.5mm (h) (see “Storage” on page D - 3). Follow your Warning operating system’s installation instructions, and install all necessary drivers and util- ities (see...
Page 95 Upgrading The Computer Grip the tab and slide the hard disk in the direction of arrow Lift the hard disk out of the bay Models A & C Figure 6 - 3 HDD Removal Models B & D Remove the screw(s) &...
Page 96: Upgrading The Optical (Cd/Dvd) Device
Upgrading The Computer Upgrading the Optical (CD/DVD) Device Turn off the computer, and turn it over and remove the battery. Models A & C: Locate the RAM & CPU bay cover and remove screws Fan Cable Carefully (a fan and cable are attached to the under side of the cover) lift up Make sure you recon- the bay cover.
Page 97 Upgrading The Computer Remove the screw at point , and use a screwdriver to carefully push out the optical device at point Reverse the process to install the new device. Models A & C Models B & D Figure 6 - 6 Removing the Optical Device Models B &...
Page 98: Upgrading The System Memory (Ram)
Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 200 pin Small Outline Dual In-line (SO- DIMM) DDRII (DDR2) type memory modules (see “Memory” on page D - 3 details of supported module types). The total memory size is automatically detected by the POST routine once you turn on your computer.
Page 99 Upgrading The Computer Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover. Carefully disconnect the fan cable , and remove the cover Figure 6 - 8 CPU/RAM Bay Cover Removed Contact Warning Gently pull the two release latches on the sides of the memory socket in the Be careful not to touch...
Page 100 Upgrading The Computer The RAM module will pop-up, and you can remove it. Figure 6 - 10 RAM Module Removal Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot.
Page 101: 3.5G And Wlan Module Location
Upgrading The Computer 3.5G and WLAN Module Location The picture below indicates the location of the 3.5G and WLAN modules for your information. Note that the 3.5G module is a factory option, and the WLAN module is an option. Neither of these modules are user upgradeable/replaceable; for more in- formation contact your customer service representative.
Page 102 Upgrading The Computer 6 - 12...
Page 103: Modules & Options
Modules & Options Chapter 7: Modules & Options Overview Wireless Device Operation Aboard This chapter contains information on the following modules, which may come with Aircraft your computer, depending on the configuration purchased. If you are unsure please The use of any portable contact your service representative.
Page 104: Bluetooth Module
Modules & Options Bluetooth Module The operating system’s Bluetooth Devices control panel is used to configure the Wireless Device Bluetooth settings in Windows Vista, and therefore does not require a driver. Use Operation Aboard the Fn + F12 key combination (see “Function/Hot Key Indicators”...
Page 105: Bluetooth Configuration In Windows Vista
Modules & Options Bluetooth Configuration in Windows Vista Setup your Bluetooth Device so the Computer Can Find it Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Bluetooth Taskbar Make the device discoverable (to do this check your device documentation). Icon If you cannot see the To Turn the Bluetooth Module On...
Page 106 Modules & Options To Add a Bluetooth Device Access the Bluetooth Devices control panel. Click Options (tab), and make sure that Allow Bluetooth devices to connect to this computer check box (Connections) has a tick inside it. Click Devices (tab), and then click Add. The Add Bluetooth Device Wizard will appear.
Page 107 Modules & Options To Change Settings for the Bluetooth Device Access the Bluetooth Devices control panel. Click on the device you want to change and click Properties to: Bluetooth Help • Change the name of the device (click General, type a new name and click OK). •...
Page 108: Pc Camera Module
Modules & Options PC Camera Module There are 2 camera options available for this computer, depending on your purchase Latest PC Camera configuration. The 1.3M pixel camera module uses the BisonCap application to Driver Information capture video files. The 2.0M pixel camera module uses the Video View applica- tion to capture video files.
Page 109 Modules & Options PC Camera Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2.0M PC Camera 2. Click Option Drivers (button). Screen Refresh 3. Click 1.PC Camera, Web cam > Yes. The 2.0M PC Camera module supports...
Page 110: 7 - 8 Pc Camera Module
Modules & Options PC Camera Audio Setup (all camera modules) If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound).
Page 111 Modules & Options Figure 7 - 5 Audio Setup for PC Camera Right-click PC Camera Module 7 - 9...
Page 112 Modules & Options BisonCap (1.3M Cam)/VideoView (2.0M Cam) BisonCap and VideoView are video viewers for general purpose video viewing and testing, and capturing video files to .avi format. Pre-Allocating File Space Run the BisonCap/VideoView program from the Start > Programs/All Programs >...
Page 113 Modules & Options Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties).
Page 114 Modules & Options Eliminating Screen Flicker If you find that the video screen in the BisonCap/VideoView program is flickering, you can try to adjust the setting in the Video Capture Filter options. Run the BisonCap/VideoView program. Go to Options and scroll down to select Video Capture Filter..For Bison Cap: Click either 50Hz or 60Hz under Frequency in Property Page (tab).
Page 115 Modules & Options Zoom The BisonCap and VideoView programs allow you to zoom the camera in and out. Run the BisonCap/Video View program. For Bison Cap: Go to Zoom and select Zoom Out/Zoom In. For Video View: Figure 7 - 7 Go to Options and scroll down to select Setting (Use the slider to adjust the zoom Zoom/Setting level, and click OK to save the setting).
Page 116: Wireless Lan Module
Modules & Options Wireless LAN Module If you have included a 802.11b/g WLAN module in your purchase option, make sure Wireless Device that the Wireless LAN module is on before installing the driver. Operation Aboard Aircraft Use the Fn + F11 key combination (see “Function/Hot Key Indicators”...
Page 117: Connecting To A Wireless Network
Modules & Options Connecting to a Wireless Network Make sure the Wireless LAN module is turned on. Click the taskbar wireless icon , and then click Connect to a network (or right- click the icon , and then click Connect to a network). Figure 7 - 8 Taskbar Menus Click icon...
Page 118 Modules & Options Click a network, and then click Connect. If you do not see a network you want to connect to, click Set up a connection or network (a list of options will appear allowing manual searching, and creating a new network).
Page 119 Modules & Options To disconnect from the wireless network you can click the taskbar wireless icon and then select Connect or disconnect to access the network menu, and click Disconnect (or right-click the icon , and then click Disconnect from). Security Enabled Networks You should try to make...
Page 120: Windows Mobility Center
Modules & Options Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. To access the Windows Mobility Center: Click Start, and click Control Panel (or point to Settings and click Control Panel).
Page 121: 3.5G Module
Modules & Options 3.5G Module If you have included an optional 3.5G module (see “Communication” on page D - Power Safety for specification details) in your purchase option, you will have the appropriate Warning software provided for your module. Follow the instructions below to install the USIM card (which will be provided by your service provider), and then install the Before you undertake any installation proce-...
Page 122 Modules & Options Insert the USIM card as you would into your mobile phone. Slide the SIMLOCK towards the hinge (in the opposite direction to the arrow illustrated in Figure 7 - 16) in order to release the lock and lift it up. Insert the USIM card as illustrated in (Figure 7 - 15) and close the SIMLOCK.
Page 123: 3G Watcher Application
Modules & Options 3G Watcher Application With the 3.5G module and USIM card (provided by your service provider) installed you may then install the 3G Watcher application. The 3.5G Watcher application al- Wireless Device lows you to directly access your 3.5G internet service from the computer. Operation Aboard Aircraft 3G Watcher Application Installation...
Page 124 Modules & Options Setting Up a Carrier Profile Although the connection information is stored on the USIM card supplied by the ser- vice provider, you will need to set up the appropriate carrier profile in 3G Watcher. Power on the 3.5G module using the Fn + key combination.
Page 125 Modules & Options You can then enter a new profile name or choose a profile from the drop-down list provided by the software (see the sidebars for information on the profile details). Figure 7 - 19 User Options Profile Information Profile Details Click General and/or Ad- vanced (and the sub-...
Page 126 Modules & Options Connecting to the Service Provider Power on the 3.5G module using the Fn + key combination. You can access the 3G Watcher application from the Start menu (Start > Programs/All Programs > Sierra Wireless > 3G Watcher), or by clicking the desktop icon The software will run and display the service provider name (see “Setting Up a...
Page 127 Modules & Options When the connection is successful a taskbar notification will appear (as below). Figure 7 - 23 Connected Taskbar Notification You can then access the internet, download e-mail etc. as per any internet connection. While you are connected the taskbar icon will be green (it will be red when the program is running but not connected).
Page 128 Modules & Options 12. If you click the 3G Watcher close icon a message will be displayed asking you to click OK to confirm the program exit. Figure 7 - 25 Exit Warning 13. Exiting the program DOES NOT turn off the 3.5G module, and you will need to press the Fn + key combination to turn off the module (pay careful attention to this aboard aircraft - see...
Page 129: Short Messaging Service
Modules & Options Short Messaging Service In addition to standard internet services you may also send and receive SMS text messages using the 3G Watcher program, if your service supports SMS. Reading SMS Messages The SMS message indicator in the main window will notify you of any new messages received.
Page 130: 7 - 28 Fingerprint Reader Module
Modules & Options Fingerprint Reader Module If you have included the fingerprint reader (optional for Models C & D only) in Help & Manual your purchase option you will need to install the driver as per the instructions below. Right-click the taskbar icon Make sure you have administrator’s rights to your computer, and have a Windows to bring up the menu to password enabled for full security protection.
Page 131: User Enrollment
Modules & Options User Enrollment Click Start > Programs/All Programs > Protector Suite QL > User Enrollment, or double click the taskbar icon On the first run of the program you will be asked to click the button to accept the license, and then click OK.
Page 132 Modules & Options Click the button above any of the fingers to begin the enrollment process for that finger. 10. Swipe the finger three times to enroll that finger. Fingerprint 11. Repeat the process for all the fingers you wish to enroll (see sidebar), and then Enrollment click Next.
Page 133 Modules & Options 15. Right-click the taskbar icon to bring up the menu that allows you to Edit Fingerprints, Start Control Center, access the Help menu etc. You can also run the Control Center etc. from the Protector Suite QL item in the Programs/All Programs menu.
Page 134 Modules & Options 7 - 32...
Page 135: Troubleshooting
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Page 136: Basic Hints And Tips
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer ap- pears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, “LED Indi- make sure it is actually working.
Page 137: Backup And General Maintenance
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wal- let.
Page 138: Viruses
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the defini- tions file updates are usually downloadable directly from the internet.
Page 139: Upgrading And Adding New Hardware/Software
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing.
Page 140 Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. •...
Page 141: Problems And Possible Solutions
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t Battery missing / incorrectly installed. Check the battery bay, make sure the work. battery is present and seated properly (the design of the battery only allows it to go in one way).
Page 142 Troubleshooting Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating”...
Page 143 Troubleshooting Problem Possible Cause - Solution You forget the boot password. If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Page 144 Troubleshooting Problem Possible Cause - Solution Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work.
Page 145 Troubleshooting Problem Possible Cause - Solution The PC Camera module cannot be The module is off. Press the Fn + F10 key combination in order to enable the detected. module (see “Function/Hot Key Indicators” on page 1 - 12). Run the BisonCap/Video View program to view the camera picture.
Page 146 Troubleshooting Problem Possible Cause - Solution The Hibernate function has disappeared. You have a computer with 4GB of RAM and have installed Windows Vista Serv- ice Pack 1. This is a known issue if your computer has 4GB of RAM and is run- ning Windows Vista Service Pack 1.
Page 147: Screen Resolution Error
Troubleshooting Screen Resolution Error If you are experiencing either screen resolution reduction, or screen flickering after resuming from Sleep in Windows Vista only then follow the instructions below to fix this problem. This error arises in compliance with Windows Vista policy, which triggers TMM (Transient Multi-Monitor Manager) when the notebook lid (S3) is closed.
Page 148 Troubleshooting Double-click Task Scheduler Library > Microsoft > Windows. Click MobilePC to open the control panel. Right-click TMM and select Disable. Figure 8 - 2 - TMM Disable Close all the control panels. 8 - 14 Screen Resolution Error...
Page 149: Interface (Ports & Jacks)
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc. Interface (Ports & Jacks) A - 1...
Page 150: Notebook Ports And Jacks
Interface (Ports & Jacks) Notebook Ports and Jacks Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer.
Page 151 Interface (Ports & Jacks) Item Description RJ-45 LAN Jack This port supports LAN (Network) functions. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port. Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store.
Page 152 Interface (Ports & Jacks)
Page 153: Sis Video Driver Controls
Appendix B: SIS Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - SIS Video Driver Installation Function Key Combination Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - You can use the Fn + Insert the Device Drivers &...
Page 154: B - 2 Sis Vga Control Center
SIS VGA Control Center More advanced video configuration options are provided by the SIS VGA Control Taskbar Icon Center. The SIS VGA Control Open the control panel (see “Windows Vista Start Menu & Control Panel” on Center can also be ac- page 1 - 17) and click SiS VGA Control Center (Appearance and Personaliza- cessed by right-clicking...
Page 155 You may make changes to the video and display settings by clicking the appropriate menu button. Figure B - 2 SIS VGA Control Center Control Panels SIS VGA Control Center B - 3...
Page 156 Display Devices & Options Besides the built-in LCD, you can also use an external VGA monitor (CRT) or ex- ternal Flat Panel Display as your display device. A VGA monitor/Flat Panel Dis- play connects to the external monitor port. The following display modes are available.
Page 157: Attaching Other Displays
Attaching Other Displays Besides the built-in LCD, you can also use an external monitor (CRT)/flat panel dis- play as your display device. Connect it to the external monitor port on the left of the computer, and configure the displays from SiS VGA Control Center : Attach your external display to the external monitor port and turn it on.
Page 158: B - 6 To Enable A Display Setting Mode
To Enable a Display Setting Mode Attach your external display to the external monitor port and turn it on. Go to the SiS VGA Control Center > Display Setting menu Click the appropriate icon for the display setting mode you wish to use. Click Yes within 15 seconds in order to save the setting change.
Page 159 Using Display Settings to Enable Extended Mode Attach your external display to the external monitor port, and turn it on. Open the Display Settings control panel (see “Video Features” on page 1 - 18). Display Settings Click the monitor icon (e.g. ), and make sure you have checked “Extend the Extended Desktop desktop onto this monitor.”...
Page 160 B - 8...
Page 161: Nvidia Video Driver Controls
NVIDIA Video Driver Controls Appendix C: NVIDIA Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - Resolution Error NVIDIA Video Driver Installation If you are experiencing Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - screen resolution...
Page 162: Nvidia Control Panel
NVIDIA Video Driver Controls NVIDIA Control Panel More advanced video configuration options are provided in the NVIDIA Control Panel tab. Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click NVIDIA Control Panel (click "Classic View" from the left of the menu if you are in Control Panel Home).
Page 163 NVIDIA Video Driver Controls The NVIDIA Control Panel provides additional video configuration controls and tools which allow quick access to features such as display configuration, 3D Settings and Help menus etc. Navigating the Control Panel Navigate through the control panels in much the same way as you would a web page.
Page 164 NVIDIA Video Driver Controls The Help menus provide index and search features, and direct links to the NVIDIA website etc. Figure C - 3 Help Menus C - 4 NVIDIA Control Panel...
Page 165: Attaching Other Displays
NVIDIA Video Driver Controls Attaching Other Displays Configuring an External Display in Windows Vista Display Devices Attach your external display to the external monitor port and turn it on. Besides built-in If a New Display Detected window does not appear in Windows Vista, go to the LCD, you can also use Windows Mobility Center control panel (Mobile PC >...
Page 166 NVIDIA Video Driver Controls Configuring an External Display using the NVIDIA Control Panel Alternatively you can use the NVIDIA control panel to configure any attached dis- plays. Attach your external display to the external monitor port and turn it on. Go to NVIDIA Control Panel (see “NVIDIA Control Panel”...
Page 167: Display Modes
NVIDIA Video Driver Controls Display Modes Single Display Mode Resolution Error Only one of your displays is used. If you are experiencing screen resolution prob- Clone Mode lems/screen flickering after Clone Mode simply shows an exact copy of the Primary display desktop on the other resuming from Sleep in display(s).
Page 168 NVIDIA Video Driver Controls Using New Display Detected to Enable Extended Mode Attach your external display to the external monitor port and turn it on. If a New Display Detected window does not appear in Windows Vista, go to the Windows Mobility Center control panel (Mobile PC >...
Page 169 NVIDIA Video Driver Controls Using Display Settings to Enable Extended Mode Attach your external display to the external monitor port and turn it on. Click Start, and click Control Panel (or point to Settings and click Control Display Settings Panel). Extended Desktop Click Adjust screen resolution under the Appearance and Personalization menu (or double-click Personalization >...
Page 170 NVIDIA Video Driver Controls C - 10...
Page 171: Specifications
Specifications Appendix D: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, delayed or updated due to the manufacturer's release schedule. Check with your service center for details.
Page 172: Processor
Specifications Feature Specification Processor Intel® Core™2 Duo Processor 45nm (45 Nanometer) Process Technology (478-pin) Micro-FC-PGA Package, Socket P 3MB On-die L2 Cache & 800MHz FSB T8100/ T8300 2.1/ 2.4 GHz Intel® Core™2 Duo Processor 45nm (45 Nanometer) Process Technology (478-pin) Micro-FC-PGA Package, Socket P 6MB On-die L2 Cache &...
Page 173: Video Adapter
Specifications Feature Specification Video Adapter Models A & B: Models C & D: SIS M672 Integrated Video nVIDIA GeForce 9300M GS (NB9M-GS) High Preference 3D/2D Graphic Accelerator Discrete Graphics On-Board Shared Memory Architecture (up to 256MB 256MB of GDDR2 Video Memory On-Board dynamically allocated from system memory where TurboCache™...
Page 174: Audio
Specifications Feature Specification Audio High Definition Audio (HDA) Direct Sound 3D™ Compatible Compliant with Microsoft UAA (Universal Audio 2 * Built-In Speakers Architecture) Built-In Microphone Keyboard & Winkey Keyboard Built-In TouchPad with Scrolling Function Pointing Device Interface Three USB 2.0 Ports One RJ-11 Modem Jack One Headphone-Out Jack One RJ-45 LAN Jack...
Page 175: Communication
Specifications Feature Specification Communication 10M/100Mb Base-T Ethernet LAN 56K MDC Modem V.90 & V.92 Compliant 3rd Party 802.11b/g Wireless LAN Mini-Card Module with USB interface (Option) Bluetooth 2.0 + EDR (Enhanced Data Rate) Module (Factory Option) UMTS Modes 1.3M (UVC or non UVC) or 2.0M Pixel USB PC Camera Module (Factory Option) Note that UMTS 3.5G Module: modes...
Page 176: Dimensions
Specifications Feature Specification Environmental Temperature Relative Humidity ° ° Spec Operating: C - 35 Operating: 20% - 80% Non-Operating: -20°C - 60°C Non-Operating: 10% - 90% Dimensions Models A & C: Models B & D: & Weight 336mm (w) * 250mm (d) * 24.8-35.7mm (h) 359mm (w) * 268mm (d) * 24.8-37mm (h) 2.2 kg With 6 Cell Battery &...
Page 177: Windows Xp Information
Appendix E: Windows XP Information This Appendix contains information (including control panel information, driver installation etc.) for users of the Windows XP OS. E - 1...
Page 178: Dvd Regional Codes
DVD Regional Codes Changing DVD Regional Codes Go to the Control Panel and double-click System > Hardware (tab), click Device Manager, then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialogue box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code.
Page 179: Windows Xp Start Menu & Control Panel
Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop.
Page 180: E - 4 Touchpad And Buttons/Mouse
TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse. Once you have installed the TouchPad driver (see “TouchPad”...
Page 181: Function Keys/Hot Key Indicators
Function Keys/Hot Key Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key utility is installed (see “Hot Key”...
Page 182: Audio Features
Audio Features You can configure the audio options on your computer from the Sounds and Audio Devices Windows con- trol panel, or from the Realtek HD Audio Manager icon in the taskbar/control panel (this will bring up the Realtek Audio Configuration menus). The volume may also be adjusted by means of the Fn + F5/F6 key com- bination.
Page 183: Video Features
Video Features This computer features two different (either SiS for Model A & B computers or NVIDIA for Models C & D computers) video options. You can switch display devices, and configure display options, from the Display Properties control panel in Windows as long as the appropriate video driver is installed. For further information see either “SiS Video Driver Controls”...
Page 184: Display Properties & Sis Utility Manager/Nvidia Control Panel
Display Properties & SiS Utility Manager/NVIDIA Control Panel Right-click taskbar icon Right-click desktop Figure E - 5 - Display Properties & Video Control Panels E - 8 Video Features...
Page 185: Sis Video Driver Controls
SiS Video Driver Controls (Models A & B) Function Key Access the SiS Utility Manager as indicated on page E - 7. You may make changes Combination to the video and display settings by clicking the appropriate menu button. You can use the Fn + F7 key combination to toggle through the dis- play options:...
Page 186: Display Devices & Modes (Sis
Display Devices & Modes (SiS) Besides the built-in LCD, you can also use an external VGA monitor (CRT) or external Flat Panel Display as your display device. A VGA monitor/Flat Panel Display connects to the external monitor port. The following display modes are available.
Page 187: Attaching Other Displays (Sis
Attaching Other Displays (SiS) If you prefer to use a monitor or flat panel display as your display device, then con- nect it to the external monitor port on the left of the computer. Secondary Device Click to put a tick in the Attach your external display to the external monitor port, and turn it on.
Page 188 To Enable Extended Desktop (Windows Display Properties) Attach your external monitor to the external monitor port, and turn it on. Click Start, point to Settings (or click Control Panel) and click Control Panel (if you are in Category View choose Appearance and Themes). Double-click Display (icon).
Page 189: Nvidia Video Driver Controls
NVIDIA Video Driver Controls (Models C & D) Navigating the Access the NVIDIA Control Panel as indicated on page E - 7. You may make Control Panel changes to the video and display settings by clicking the appropriate menu item. Navigate through the control panels in much the same way as you...
Page 190: Display Devices And Modes (Nvidia
Display Devices and Modes (NVIDIA) Besides the built-in LCD, you can also use an external VGA monitor (CRT) or external Flat Panel Display as your display device. A VGA monitor/Flat Panel Display connects to the external monitor port. The following display modes are available.
Page 191: Attaching Other Displays (Nvidia
Attaching Other Displays (NVIDIA) Attach your external display to the external monitor port and turn it on (see sidebar). Go to the NVIDIA Control Panel. Function Key Click Display, and then click Set Up Multiple Displays. Combination You can use the Fn + F7 key combination to tog- gle through some dis- play options:...
Page 192 To Enable Extended Desktop (Windows Display Properties) Attach your external monitor to the external monitor port, and turn it on. Click Start, point to Settings (or click Control Panel) and click Control Panel (if you are in Category View choose Appearance and Themes). Double-click Display (icon).
Page 193: Power Management Features
Power Management Features To conserve power, especially when using the battery, your computer uses the ACPI OS Note power management system. Power management conserves power by controlling in- dividual components of the computer (the monitor and hard disk drive) or the whole Power management system.
Page 194: The Power Sources
The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/DC adapter will damage the computer and its components. Attach the AC/DC adapter to the DC-in jack on the left of the computer.
Page 195: Turning On The Computer
Turning On the Computer Now you are ready to begin using your computer. To turn it on simply press the pow- Shutdown er button on the front panel. Note that you should al- When the computer is on, you can use the power button as a Stand by/Hibernate/ ways shut your comput- er down by choosing the Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and...
Page 196: Power Schemes
Power Schemes You can set your computer to conserve power through individual components by Resuming means of Power Schemes. You can also adjust the settings for each scheme to set Operation the monitor to turn off after a specified time, and the computer's hard disk motor to turn off if the hard disk drive has not been accessed for a specified period of time (if Press a key on the key- the system reads or writes data, the hard disk motor will be turned back on).
Page 197 Each Windows Power Scheme will also adjust the processor performance of your machine in order to save pow- er. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose the Home/Office Desk scheme for maximum performance when the computer is powered from an AC power source.
Page 198: Hibernate Mode Vs. Shutdown
System Power Options You can use the system power options to stop the computer’s operation and restart Stand by/Hibernate where you left off. This system features Stand by and Hibernate sleep mode levels or Shutdown Error (Hibernate mode will need to be enabled by clicking the option in the Hibernate tab in the Power Options control panel - see “Hibernate”...
Page 199 Stand by Stand by saves the least amount of power, but takes the shortest time to return to full operation. During Stand by the hard disk is turned off, and the CPU is made to idle System Resume at its slowest speed. All open applications are retained in memory. When you are not The system can resume using your computer for a certain length of time, which you specify in the operating from Stand by mode by:...
Page 200: E - 24 Configuring The Power Button
Configuring the Power Button The power button may be set to send the computer in to either Stand by or Hiber- Sleep Button nate mode. In Stand by mode, the LED will blink green. In Hibernate mode the LED will be off (battery) or orange (AC/DC adapter). If you are in a power saving You may also configure mode set to save power through individual components (e.g.
Page 201: Battery Information
Battery Information Please follow these simple guidelines to get the best use out of your battery. Low Battery New Battery Warning Always completely discharge, then fully charge, a new battery (see “Battery FAQ” When the battery is criti- on page E - 28 for instructions on how to do this).
Page 202: Recharging The Battery With The Ac/Dc Adapter
Battery life may be shortened through improper maintenance. To optimize the life and improve its perfor- mance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you need to remove the battery for any reason, “Removing the Battery”...
Page 203 Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Damaged Battery Warning Should you notice any physical defects (e.g.
Page 204: Battery Faq
Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t Caution turn off the computer by yourself even when you see a message that indicates the bat- Danger of explosion if tery is critically low, just let the computer use up all of the battery power and shut battery is incorrectly re-...
Page 205 Driver Installation 1. Check the driver installation order from Table E - 5 (the drivers must be installed in this order) which is the Insert the Device Drivers & Utilities + User’s Manual same as that listed in the Drivers Installer menu below.
Page 206: Driver Installation
Updating/Reinstalling Individual Drivers WinXP SP2 Driver Page # If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go Video Page E - 31 to the Control Panel in the Windows OS and double- Audio Page E - 32 click the Add/Remove Programs item.
Page 207: Driver Installation Procedure
Driver Installation Procedure Video Windows XP Service Pack 2 1. Click 1.Install Video Driver > Yes. Make sure you install Windows XP Service Pack 2 (or a Windows XP version which includes Service Pack 2) be- Models A & B (SiS): fore installing any drivers.
Page 208 Audio 1. Click 2.Install Audio Driver > Yes. 1. Click 4.Install Lan Driver > Yes. 2. Click Next. 2. Click Next. 3. Click Finish to restart the computer. 3. Click Finish > Finish to restart the computer. 4. The network settings can now be configured. Modem TouchPad 1.
Page 209: Module Drivers
Module Drivers Wireless LAN, Bluetooth & 3.5G Modules See the following pages for the driver installation pro- cedures for any of the optional modules included in Wireless Device Operation Aboard Aircraft your purchase configuration. The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Page 210: Bluetooth Module
Bluetooth Module The operating system’s Bluetooth Devices control panel is used to configure the Bluetooth settings in Windows XP, and therefore does not require a driver. Use the Fn + F12 key combination (see “Function Keys/Hot Key Indicators” on page E - 5) to toggle power to the Bluetooth module.
Page 211 Bluetooth Local Area Connection Icon If you want to display the Local Area Connection icon for the Bluetooth connection in the taskbar, set it up as follows: Wireless Device Operation Aboard Access the Network Connections control panel in Windows (Start > Settings > Aircraft Network Connections OR Start >...
Page 212: Bluetooth Configuration In Windows Xp
Bluetooth Configuration in Windows XP Setup your Bluetooth Device so the Computer Can Find it 1. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Bluetooth Taskbar 2. Make the device discoverable (to do this check your device documentation). Icon To Turn the Bluetooth Module On If you cannot see the...
Page 213: To Add A Bluetooth Device
To Add a Bluetooth Device Access the Bluetooth Devices control panel. Click Options (tab), and make sure that Allow Bluetooth devices to connect to this computer check box (Connections) has a tick inside it. Click Devices (tab), and then click Add. The Add Bluetooth Device Wizard will appear.
Page 214 To Change Settings for the Bluetooth Device 1. Access the Bluetooth Devices control panel. 2. Click on the device you want to change and click Properties to: • Change the name of the device (click General, type a new name and click OK). •...
Page 215: Pc Camera Module
PC Camera Module Before installing the optional PC Camera module driver use the Fn + F10 key com- bination to toggle power to the module. There are 3 camera options available for this Taking Still Pictures computer, depending on your purchase configuration. The 1.3M pixel camera mod- Double-click ule uses the BisonCap application to capture video files.
Page 216 For the 2.0M Pixel Camera Module: 1. Click Install. 2. Click to select Yes or No in answer to the power system question. 3. Click Finish > Finish to restart the computer. 4. Run the Video View application program from the Video View shortcut on the desktop, or from the USB2.0 PC Camera item in the Start >...
Page 217 BisonCap (1.3M Cam)/VideoView (2.0 Cam) BisonCap and VideoView are video viewers for general purpose video viewing and testing, and capturing video files to .avi format. Pre-Allocating File Space 1. Run the BisonCap/VideoView application from the Start > Programs/All You may pre-allocate Programs >...
Page 218 Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties) If necessary you can remove the recorded video file to a removable medium e.g.
Page 219 Eliminating Screen Flicker If you find that the video screen in the BisonCap/VideoView program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. Run the BisonCap/VideoView program. 2. Go to Options and scroll down to select Video Capture Filter..For Bison Cap: 3.
Page 220 Zoom The BisonCap and VideoView programs allow you to zoom the camera in and out. 1. Run the BisonCap/VideoView program. For Bison Cap: 2. Go to Zoom and select Zoom Out/Zoom In. Figure E - 7 For VideoView: Zoom/Setting 3. Go to Options and scroll down to select Setting (use the slider to adjust the zoom level, and click OK to save the setting).
Page 221: Wlan Module
WLAN Module Before installing the optional 802.11b/g USB WLAN module driver use the Fn + Wireless Device F11 key combination to toggle power to the module. Operation Aboard Aircraft 802.11b/g WLAN Driver Installation The use of any portable 1. Make sure the module is powered on, then insert the Device Drivers & Util- electronic transmission de- ities + User’s Manual disc into the CD/DVD drive.
Page 222 Network Connection Use the Windows Net- work Connections con- trol panel access available wireless net- works (Start > Settings > Network Connections or Start > Connect To > Show all Connections). Figure E - 8 Wireless Network Control Panels E - 46 WLAN Module...
Page 223: 3.5G Module
3.5G Module If you have included an optional 3.5G module in your purchase option follow the instructions on page 7 - 19 install the USIM card (which will be provided by your service provider), and then install the application. Before installing the application, make sure that the 3.5G module is on. Use the Fn + key combination (see “Function/Hot Key Indicators”...
Page 224: E - 48 Fingerprint Reader Module
Fingerprint Reader Module If you have included the fingerprint reader in your purchase option (optional for Help & Manual Models C & D only) you will need to install the driver as per the instructions below. Right-click the taskbar icon Make sure you have administrator’s rights to your computer, and have a Windows to bring up the menu to password enabled for full security protection.
Page 225 User Enrollment Click Start > Programs/All Programs > Protector Suite QL > User Enrollment, or double click the taskbar icon On the first run of the program you will be asked to click the button to accept the license, and then click OK. Click Next and select “Enrollment to the hard disk”, and click Finish.
Page 226 10. Click Finish. 11. Click any of the headings under “Learn more about:” to get more information on any topic. 12. Click Close. 13. Right-click the taskbar icon to bring up the menu that allows you to Edit Fingerprints, start Control Center, access the Help menu etc.

This manual is also suitable for:

Model d Model b Model c

Intel Model A User Manual

Quick Start Guide

Features & Components

Power Management

Drivers & Utilities

BIOS Utilities

Upgrading the Computer

Modules & Options

Troubleshooting

Interface (Ports & Jacks)

SIS Video Driver Controls

NVIDIA Video Driver Controls

Specifications

Windows XP Information

Quick Links

Need help?

Questions and answers

Related Manuals for Intel Model A

Summary of Contents for Intel Model A