Related Manuals for Samlex Europe WSC-1215
Summary of Contents for Samlex Europe WSC-1215
- Page 1 BATTERY CHARGER Smart Battery Charger Model No. WSC-1215 (SB) WSC-1230 (SB) WSC-2408 WSC-2415 Manual Please read this manual carefully before installing and starting up this device.
- Page 2 Figure 1 WSC-1215SB / WSC-1230SB Charger Front View Figure 2 WSC-1215 / 1230 / 2408 / 2415 Charger Front View...
- Page 3 Figure 3 Charger Rear View Figure 4 WSC-1215 / WSC-2408 Charger Top View (mm)
- Page 4 Figure 5 WSC-1215 / WSC-2408 Charger Side View (mm) Figure 6 WSC-1230 / WSC-2415 Charger Top View (mm)
- Page 5 Figure 7 WSC-1230 / WSC-2415 Charger Side View (mm) Figure 8 Making Connections...
- Page 6 Figure 9 Cable Setup Figure 10 Fork...
- Page 7 Figure 11 Switch Figure 12 Temperature Sensor TF-100...
- Page 8 Figure 13 Remote Controller RC-600 Figure 14 Remote Controller RC-600 Dimension (mm)
- Page 9 Figure 15 Remote Controller RC-601D Figure 16 Remote Controller RC-601D Dimension (mm)
- Page 10 Figure 17 Making Connections (RC-601D) Figure 18 Temperature Sensor Setup...
-
Page 11: Table Of Contents
Contents 1 General safety and Installation instructions 1.1 Operate the device safely 1.2 Safety instructions when installing the device 1.3 Electrical cables 1.4 Installation on boats 2 WARNING 3 Applications and Descriptions 4 Introduction of the unit variants 5 Accessories 5.1 Temperature Sensor TF-100 5.2 Remote Controller RC-600 5.3 Remote Controller RC-601D... -
Page 12: General Safety And Installation Instructions
General safety and Installation instructions 1.1 Operate the device safely Warning! Failure to observe this instruction can cause material damage, device malfunction, or danger of bodily injuries. Fundamental safety measures should be observed when using electrical equipment to avoid the danger of: –... -
Page 13: Warning
WARNING Warning! Please read carefully about the following precautions. Damages caused by failure to follow the instructions below will NOT be covered by warranty. • Use the charger only as intended. • Do NOT operate the charger if the housing or the cables are damaged. •... -
Page 14: Introduction Of The Unit Variants
Connection for AC input 100~240 volts voltage Plug holder Front view Model-No.: WSC-2408, WSC-2415 (See Figure 2 WSC-1215 / 1230 / 2408 / 2415 Charger Front View, Page. 2) The units can charge up to two supply batteries. No. Description "TEMP"... -
Page 15: Accessories
Accessories 5.1 Temperature Sensor TF-100 The temperature sensor (Figure 12 Temperature Sensor TF-100, Page. 7) measures the temperature of the battery or the environment around the battery and transfers the data to the charger. With deviating temperatures, the charging voltage increases and decreases accordingly. -
Page 16: Remote Controller Rc-601D
Accessories 5.2.2 Installation • Ensure approximately 49mm width, 49mm height and 23mm depth for the take-up of the remote controller (see Figure 14 Remote Controller RC-600, Page. 8). • Connect the remote control to the charger. The connection cable is equipped with two equivalent modular plugs. -
Page 17: Mounting Of Battery Charger
The length of RC-601D cable is 10M Mounting of Battery Charger For mounting battery charger on wall or flat places (please refer from Figure 4 WSC-1215 / WSC-2408 Charger Top View, Page. 3 and Figure 6 WSC-1230 / WSC-2415 Charger Top View, Page. 4) regarding the size of housing and the location of mounting holes for your installation. -
Page 18: Settings
(see Figure 11 Switch, Page. 7). Warning! Please follow the table below to ensure correct operation of the charger Settings for the charging voltage for WSC-1215, WSC-1215SB, WSC-1230, WSC-1230SB, WSC-2408 and WSC-2415: Table 8-1 Switch Configure Charging Voltage... -
Page 19: Half Power Mode Setting
Settings Table 8-3 Switch Configure Power/Charger Mode Switch 4 Operation mode Battery charger Power supply 13.2V/26.4V Table 8-4 Switch Configure Uo Phase Time Limit Switch 5 Switch 6 Charging time 4 hours 6 hours 8 hours Unlimited 8.2 Half power mode setting When the switch S2 “HALF POWER”... -
Page 20: Void Setting Table
Making Connections 8.4 VOID setting table To avoid the void setting, please refer to Table 8-5 VOID Setting table for pushing switch on front panel, Page. 20. Table 8-5 VOID Setting table for pushing switch on front panel Push switch on front Original working mode panel Half power... - Page 21 Using the Charger 9.1.1 I phase (bulk) The "STATUS" LED constantly lights Red. In the first stage of the charging process, the depleted battery is charged with a constant current until the battery voltage reaches I phase setting voltage (13.5V/13.8 V or 27.0V/27.6 V).
-
Page 22: Using The Remote Controller Rc-600
Once the equalization function is activated, it can only be cancelled by turning off the battery charger. Note The battery chargers WSC-1215 and WSC-1230 have an option to have a 2A charging output for the starter battery (WSC-1215SB, WSC-1230SB). The output voltage is 13.8V and can recharge the starter battery with a current of 2A or keep it at a high capacity level. -
Page 23: Units With Temperature Sensor Tf-100
Using the Charger Table 9-1 VOID Setting table for pressing button on remote controller Charger working mode RC-600 buttons Half power Equalization Others Power Supply Enter "HALF Exit "HALF "HALF POWER" POWER" VOID POWER" VOID pressed ("STATUS" LED ("STATUS" LED lights) flashing) Equalization... - Page 24 Using the Charger Figure 20 Temperature Compensation for 12V Model Figure 21 Temperature Compensation for 24V Model...
-
Page 25: Fan Speed
("E.Q." LED flashing Red and "STATUS" LED lights Orange), and auto recover when tempe- rature drops to 45°C. • The output voltage from option 2A charging output for WSC-1215 and WSC-1230 is fixed, NOT adjus- ted according to TF-100. -
Page 26: Trouble Shootings
Using the Charger Table 9-2 Normal Functional Check Table "E.Q." LED "STATUS" LED Status Red, constantly lit I phase Orange, constantly lit Uo phase Green, constantly lit U phase Red, constantly lit Red, constantly lit I phase, Equalization is acti- vated Red, constantly lit Orange, constantly lit... -
Page 27: The Battery Voltage Would Not Increase After Charging
Trouble Shootings 10.2.1 12 V battery If the multi-meter displays a voltage of 10 V or less, this indicates that the battery is defective and can not be charged any longer. 10.2.2 24 V battery If the multi-meter indicates a voltage of 20 V or below, allow the battery be checked by a specialist, if necessary. -
Page 28: Specifications
Specifications Model Number: WSC-1215 WSC-1215-SB WSC-2408 Input voltage range 100-240V AC Input frequency 50-60Hz Power factor correction >0.97 Efficiency at 230V AC >90% >91% Efficiency at 115V AC >87% >88% Input Current at 230V AC 1.1A 1.1A Input Current at 115V AC 2.1A... - Page 29 Specifications Model Number: WSC-1230 WSC-1230SB WSC-2415 Input voltage range 100-240V AC Input frequency 50-60Hz Power factor correction >0.97 Efficiency at 230V AC >91% >92% Efficiency at 115V AC >89% >90% Input Current at 230V AC 2.0A 2.2A 2.0A Input Current at 115V AC 4.2A 4.4A 4.0A...
-
Page 30: Declaration Of Conformity
Model No.: WSC-1215,WSC-1215SB,WSC-1230,WSC-1230SB,WSC-2408, WSC-2415 Trade Name: Applicant: SAMLEX EUROPE B. V. Address: ARIS VAN BROEKWEG 15, 1507 BA ZAANDAM THE NETHERLANDS Is herewith confirmed to comply with the EMC requirements set out in the Directive 2014/30/EU and LVD requirements set out in the Directive 2014/35/EU of the European Parliament and of the Council of April 20, 2016 on the approximation of the laws of the Member States relating to electromagnetic compat- ibility and EC Low Voltage Directive. - Page 31 www.samlex.com www.samlex-solar.com...
Need help?
Do you have a question about the WSC-1215 and is the answer not in the manual?
Questions and answers