Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Samlex Europe Omnicharge OC12-90
Summary of Contents for Samlex Europe Omnicharge OC12-90
- Page 1 PROFESSIONAL BATTERYCHARGER Omnicharge Programmable Batterycharger Model No. OC12-90 OC24-50 OC24-80 Manual, Gebruiksaanwijzing, Benutzerhandbuch, Manuel Utilisateur, Manual Para Utilizador Please read this manual before operating your batterycharger...
- Page 2 No part of this document may be reproduced in any form or disclosed to third parties without the express written permission of Samlex Europe BV, Aris van Broekweg 15, 1507BA ZAANDAM, The Netherlands. Samlex Europe BV reserves the right to revise this document and to periodically make changes to the content hereof without obligation or organization of such revisions or changes, unless required to do so by prior arrangement.
-
Page 3: Table Of Contents
TABLE OF CONTENTS 1. INTRODUCTION ........................3 2. INSTALLATION ........................4 Unpacking ........................4 Mounting ........................4 Accessing the connection compartment ..............5 Wiring details ....................... 6 2.4.1 Control board connections and settings ..............8 2.4.2 Bottom side connections ..................9 Parallel operation ...................... -
Page 4: Introduction
1. INTRODUCTION Thank you for purchasing a Samlex Europe (SAMLEX) Omnicharge battery charger. Please read this owner’s manual for information about using the product correctly and safely. Keep this owner’s manual and all other included documentation close to the product for future reference. -
Page 5: Installation
2. INSTALLATION Unpacking The charger package should contain the following items : - Battery charger - Wall bracket - Battery temperature sensor (3m) - Owner’s manual - Safety flyer - Charger warning stickers - 2x M8 crimp terminals - 7x mounting screws CAUTION After unpacking, check if the product shows any mechanical damage. -
Page 6: Accessing The Connection Compartment
CAUTION Keep a clear space of at least 10 cm around this product for cooling purposes! Always mount this product in an upright position. Floormounting is allowed as well, provided that all 7 screws are used to secure the enclosure. WARNING To reduce the risk of explosion, never use this product in locations where there is danger of gas- or dust explosions or where ignition protected equipment is mandatory. -
Page 7: Wiring Details
Wiring details Please see the image below for the wiring details. ① Please consult the following table to determine the correct battery cable and fuse size for each model. Using a smaller cable size or a longer cable will cause additional losses and may result in improperly charged batteries. - Page 8 Model Cable size Cable size Battery fuse (length ≤ 3 m) (length = 3 to 6m) (quick type) OC12-90 35mm (AWG2) 50mm (AWG0) 100-120Amp OC24-50 25mm (AWG3) 35mm (AWG2) 60-80Amp OC24-80 35mm (AWG2) 50mm (AWG0) 100-120Amp ② The AC input must be protected by an earth leakage circuit breaker with overcurrent protection (RCBO), that can withstand the maximum nominal current consumption from the charger without tripping.
-
Page 9: Control Board Connections And Settings
2.4.1 Control board connections and settings The following image shows the control board connections and switch options. ① Master/slave switch position. This switch must be set to ‘MASTER’ when a single charger is installed. The ‘SLAVE’ setting is only relevant for parallel charger systems. ②... -
Page 10: Bottom Side Connections
2.4.2 Bottom side connections Please see the next image for the bottom side connections. SAMLEXLink to USB interface (optional) Parallel operation Up to 6 battery chargers of the same model can be connected in parallel, in order to reach very high charge current levels. This manual will not show any connection or operation details for paralleled charger systems. -
Page 11: Configuring The Battery Charger
3. CONFIGURING THE BATTERY CHARGER Selecting the correct charge program The image in chapter 2.4 showed the location of the rotary selector, which is used to select the desired charge program. The charge program selection depends on the type of battery that needs to be charged. - Page 12 Absorption voltage = 14.70V or 29.40V (also for Float voltage = 13.65V or 27.30V Optima Equalize voltage = 15.50V or 31.00V SpiralCell) Max. bulk time = 8hrs Max. absorption time = 4hrs Position 3 Lead Absorption voltage = 14.80V or 29.60V Calcium Float voltage = 13.50V or 27.00V Equalize voltage = 15.80V or 31.60V...
-
Page 13: Charge Programs Explained
Charge programs explained Most standard selectable charge programs, perform a four stage IUoUoP charging process comprising of a “Bulk” , an “Absorption”, a “Float” and a “Pulse” stage. The image below visualizes the four stage charging process : In the Bulk stage, the charger delivers full output current and typically returns approximately 80% of charge back into the battery once the absorption voltage is reached. - Page 14 battery must supply this which results in a declining battery voltage. At a certain battery voltage level, the charger jumps back to the Bulk stage and will finalize a complete four stage charging process again, once the battery load consumption has dropped below the charger's maximum output current level.
-
Page 15: General Operation
4. GENERAL OPERATION Omnicharge display and control overview See the next image for an overview of all LED indicators on the Omnicharge frontpanel, as well as the location of the main switch. The frontpanel can be divided into four sections : ①... -
Page 16: Charging Batteries
Flashing red (3 flashes per sec.) High charger temperature The charger automatically restarts when the temperature is below an acceptable level. Flashing red (4 flashes per sec.) Charger error (return for service) ③ Charge status bar. Gives a rough indication of the charging progress, see below : LED 3a : 100% full (ready) LED 3b : 80% full LED 3c : 50% full... -
Page 17: Equalizing A Flooded Battery
Equalizing a flooded battery If you are using a lead acid battery, an occasional equalization charge cycle may be recommended by the manufacturer. This might also be true when the battery has been very deeply discharged or often charged inadequately. During equalization, the battery will be charged up to approx. -
Page 18: Troubleshooting Guideline
5. TROUBLESHOOTING GUIDELINE Please see the table below if you experience any problems with the Omnicharge battery charger and/or the installation. Problem Possible cause Remedy Omnicharge is not working at Main switch in Off (0) Push the power switch in the all. - Page 19 Charge current is too low. High ambient temperature. Try to lower the ambient temperature around the charger. Charger is operating in the Do nothing. The battery is absorption charging stage. almost fully charged and consumes less current by itself. Charge voltage is too low. The charge voltage is being Do nothing or try to cool compensated by the battery...
- Page 20 Too high ambient Move the charger to a cooler temperature. environment or provide additional cooling by an external fan. LED ‘charger on’ is blinking An internal error is detected. Please return the charger to red four times per second your nearest dealer for (charger error).
-
Page 21: Technical Specifications
6. TECHNICAL SPECIFICATIONS Parameter OC12-90 OC24-50 OC24-80 AC input voltage 100-260Vac / 47-63Hz / PF > 0.9 180-260Vac Full load power consumption 1550VA 1700VA 2750VA AC input current (115V/230V) 13.5A / 6.8A 15A / 7.5A - / 12A 1) 4) Total DC output current Nominal DC output voltage 12Vdc... -
Page 22: Warranty Conditions
7. WARRANTY CONDITIONS Samlex Europe (SAMLEX) warrants this product to be free from defects in workmanship or materials for 24 months from the date of purchase. During this period SAMLEX will repair the defective product free of charge. SAMLEX is not responsible for any costs of the transport of this product. -
Page 23: Declaration Of Conformity
8. DECLARATION OF CONFORMITY IMPORTER : Samlex Europe B.V. ADDRESS : Aris van Broekweg 15 1507 BA ZAANDAM The Netherlands Declares that the following products : PRODUCT TYPE : Professional programmable battery charger MODELS : OC12-90, OC24-50, OC24-80 Conforms to the requirements of the following Directives of the European Union :... - Page 24 www.samlex.com www.samlex-solar.com...