Page 1
The contents of this manual are based on the latest product information available FOR YOUR CONVENIENCE, RECORD THE FOLLOWING IMPORTANT at the time of publication. Pacific Steamex reserves the right to make changes or INFORMATION: improvements to its machines without notice.
DRAWING 01 Item Part Number Description Qty. Item Part Number Description Qty. 69816010 Base: Brush Drive 40346270 Cover: Base 41601100 Plate 72901002 Carbon Brush Holder 40301010 Support 880952 Carbon Brush Motor 40303310 Support 72901001 Spring 40228500 Plate 73501105 Clamp 41601010 Pipe 73501106 Hook Assembly...
DRAWING 03 Item Part Number Description Qty. Item Part Number Description Qty. 69903100 Frame 40312280 69903200 Rear Frame 40312240 Lever 67050060 Castor Wheel 69102250 Bushing 69102040 Bushing 69220160 Spring 40303280 Shaft 40312250 Lever 40303300 Left Lever 40312260 Blade 40303260 Lever 74100007 Knob 40303270...
Page 17
DRAWING 07 Item Part Number Description Qty. 69603080 Squeegee Body 67703170 Central Rubber 33 Shore 67703160 Central Rubber 40 Shore (standard) 67703180 Rear Rubber Oil-Resistant 68803090 Blade 41811060 Plate 71405002 Spring Pin 67703150 Front Rubber 68803080 Left Blade 68803070 Right Blade 40411020 Special Washer 40411010...
Page 25
DRAWING 11 Item Part Number Description Qty. Item Part Number Description Qty. 40716390 Panel 980042 Washer: 6x12 40316280 Plate 980053 Lock Washer 40716320 Left Support 980039 Washer: 8x17 40716330 Right Support 980043 Washer 40746080 Panel Left 71104006 Washer 40746090 Panel Right 980069 Washer 40746140...
DRAWING 12 Item Part Number Description Qty. Item Part Number Description Qty. 41628120 Support 40351060 Protection 69516030 Handle Bar Right 72908017 Keys, Set of Two (GREY COVER) 69516040 Handle Bar Left 72199018 Flange 41628110 Lever 980054 Washer: 3x8 41628130 980058 Lock Washer 70230008 Snap...
DRAWING 13 Item Part Number Description Qty. Item Part Number Description Qty. 40703290 Support 69210580 Spring 40703340 Lever 40703360 Bracket 71120002 Washer 887341 Snap Ring 40703280 Bushing 40703400 Pin Assembly 40703310 74100005 Knob, pressure adjustment 69106020 Bushing 40651110 Commutator 66200400 Actuator Assembly 72908005 66250010...
Page 30
BROWN YELLOW VIOLET GREEN BLUE YELLOW ORANGE YELLOW BLUE GREEN GREEN BROWN...
Page 31
COMPONENTS - ELECTRICAL SYSTEM 26B & 32B Item Part Number Description Qty. Item Part Number Description Qty. 72300111 Indicator Lamp Green Relay General 72102005 Switch with Green Lamp Relay 72300117 Indicator Battery Control Relay 72300111 Indicator Lamp Green 72403502 Fuse 35A Suction Motor 72107004 Contact On/Off Key 72408001...
Page 32
CABLES - ELECTRICAL SYSTEM 26B & 32B Item Part Number Description Qty. Item Part Number Description Qty. 68003020 2 Cables Red - Black 68003022 2 Cables Red - Black 16x800 - 25-26 with 68001034 Cable Black Connector 68001035 Cable Red 68000153 Cable + - Battery W/Screw &...
Page 34
CHOPPER CARD 67900041 1 mm tolerance between plastic body and metal part Brake Microswitch Forward Microswitch Backward Microswitch Potentiometer Insert point to check the correct centering of the potentiometer. 1 2 3 4 5 6 7 Trimmer current motor Trimmer adjustment Volt max battery Trimmer adjustment backward speed...
Page 35
CHOPPER CARD LED ALARM DESCRIPTIONS PART NUMBER 67900041 ALARM DESCRIPTIONS NUMBER OF BLINKS The chopper power section or the drive power switch are already active when the machine is switched on. The forward microswitch is active when the machine is switched on. The backward microswitch is active when the machine is switched on.
Page 36
ADJUSTMENTS AND INSPECTIONS 26B AND 32B INSPECTION OF ELECTRICAL EQUIPMENT Location Check the functionality of electrical components. 1. Disconnect the battery plug. Drawing 12 - Page 24 2. Make sure the battery terminals are clean and tight. 3. Check the power cable connections: remote control switches, fuses, motors, etc. 4.
Page 37
ADJUSTMENTS AND INSPECTIONS 26B AND 32B Chopper Card Adjustment continued Location e) Adjust the trimmer Volt minimum: At the release of the forward and backward microswitches, the motor Wiring-Item 22-Page 28 tension should be set at approximately 3-5 Volts. f) Adjust the trimmer Volt maximum for battery: At maximum speed, there should be 36 Volts across the Wiring-Item 24-Page 28 motor terminals.
Page 38
ADJUSTMENTS AND INSPECTIONS 26B AND 32B INSPECTION OF VACUUM ASSEMBLY CONTINUED Location 3. Check the vacuum hose and the squeegee hose connections. Drawing 09-Item 11-Page 18 Drawing 08-Item 19-Page 16 4. Check the cleanliness and the tightness of the squeegee hose on the tank outlet. Drawing 08-Item 19-Page 16 5.
Page 39
ADJUSTMENTS AND INSPECTIONS 26B AND 32B BRUSH ADJUSTMENT CONTINUED Location 2. The rear section of the brushes should touch the floor at the same time. The front of the brushes should be Drawing 01-Item 04-Page 2 about 5 to 8 mm (0.2 to 0.3 inches) higher than the rear section. Adjust the support forward or backward if necessary.
Page 40
ADJUSTMENTS AND INSPECTIONS 26B AND 32B BRAKE ADJUSTMENT Location 1. Handbrake: The distance from the lever to the microswitch should be no more than 3 to 4 mm. To obtain, Drawing 05-Item 10-Page 10 adjust the length of the brake cable. Drawing 05-Item 09-Page 10 Drawing 05-Item 05-Page 10 2.
1. After the expiration of the ninety (90) day travel time warranty period, the customer is responsible for warranty travel payment or the inoperative machine or warranted parts must be delivered to the authorized dealer with shipping and delivery charges prepaid. If unable to locate the Dealer, you may contact Pacific at the address listed herein for the location of the nearest Pacific repair center or agent or for other instructions pertaining to your warranty difficulty.