Clarke US1500DC 01540A Operator's Manual

Clarke US1500DC 01540A Operator's Manual

Ultra speed burnisher 120v & 240v with nema plug
Hide thumbs Also See for US1500DC 01540A:
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

Operator's Manual / Manual del operador / Manuel de l'utilisateur
ACTIVE MODELS: 01540A(US1500DC / 120V), 01550A(US2000DC / 120V)
OBSOLETE MODELS: 01530A(US1500 / 120V), 01531A(US1500 / 240V), 01491B(ROSE WORKHORSE),
01541A(US1500DC / 240V), 01551A(US2000DC / 240V)
READ THIS BOOK
LEA ESTE MANUAL
LISEZ CE MANUEL
This book has important information for the use and safe operation of this machine. Failure to read
this book prior to operating or attempting any service or maintenance procedure to your Clarke
machine could result in injury to you or to other personnel; damage to the machine or to other
property could occur as well. You must have training in the operation of this machine before using
it. If your operator(s) cannot read this manual, have it explained fully before attempting to operate
this machine.
All directions given in this book are as seen from the operator's position at the rear of the ma-
chine.
Form No. 71280A 1/2009 revised 10/2016 REV F
Ultra Speed
Burnisher
120V & 240V
with NEMA Plug
English (2 - 12)
EN
Español (14 - 24)
ES
Français (26 - 36)
FR

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the US1500DC 01540A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Clarke US1500DC 01540A

  • Page 1 This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well.
  • Page 2: Table Of Contents

    Nilfi sk Inc. Unapproved modifi cations will void the machine warranty and make the cus- tomer liable for any resulting accidents. -2- FORM NO. 71280A Clarke Operator's Manual (EN) - Ultra Speed Burnisher ®...
  • Page 3: Operator Safety Information

    Any alterations or modifi cations of this machine could result in damage to the machine or injury to the operator or other bystanders. Alterations or modifi cations not authorized by the manufacturer voids any and all warranties and liabilities. Clarke Operator's Manual (EN) - Ultra Speed Burnisher FORM NO.
  • Page 4: Features And Specifi Cations

    976240 UHS Aqua Burnish 1500-3000 Aqua Soft fi nish/low traffi c Buffer Wet-look soft fi nish 976238 SHS Buffer Buff Dry/Spray 600-1500 Beige Glossy fi nish Spray -4- FORM NO. 71280A Clarke Operator's Manual (EN) - Ultra Speed Burnisher ®...
  • Page 5: 120 Volt Instructions For Electrical Connection

    If you use an extension cord, use an extension cord with mini- mum wire size 12 AWG. Do not use an extension cord longer than 50 feet. Do not join two extension cords. Clarke Operator's Manual (EN) - Ultra Speed Burnisher FORM NO. 71280A - 5 -...
  • Page 6: 240 Volt Instructions For Electrical Connection

    If you use an extension cord, use an extension cord with mini- mum wire size 12 AWG. Do not use an extension cord longer than 50 feet. Do not join two extension cords. -6- FORM NO. 71280A Clarke Operator's Manual (EN) - Ultra Speed Burnisher ®...
  • Page 7: How To Prepare Machine For Operation

    4. Carefully center the pad on the pad driver (B). Failure to center may cause vibration and operator fatigue. 5. Screw the pad holder (A) into position. 6. Return the machine to an upright position. Figure 2 Clarke Operator's Manual (EN) - Ultra Speed Burnisher FORM NO. 71280A - 7 - ®...
  • Page 8: How To Operate The Machine

    Re-install the cover and tip the machine back upright. -8- FORM NO. 71280A Clarke Operator's Manual (EN) - Ultra Speed Burnisher ®...
  • Page 9 Inspection and Repairs Take the machine to the nearest Clarke authorized repair location once a year for the maintenance inspections. To make any repairs, take the machine to the nearest Clarke au- thorized repair location. WARNING: Maintenance and repairs...
  • Page 10: How To Correct Problems In The Machine

    The machine is vibrating excessively. Center the pad properly. The pad is worn or damaged. Install a new pad. The pad is defective. Inspect and install a new pad. -10- FORM NO. 71280A Clarke Operator's Manual (EN) - Ultra Speed Burnisher ®...
  • Page 11: Maintenance

    To check the commutator and the carbon brushes, follow this procedure: Remove the screws and covers. Clarke Operator's Manual (EN) - Ultra Speed Burnisher FORM NO. 71280A - 11 - ®...
  • Page 12 3. Turn the pad driver and look at the part of the commutator that the brushes touch. 4. Take the machine to a Clarke authorized repair location if you see any of the following conditions: 1.) Small holes in the surface of the commuta- SMALL tor.
  • Page 13 ENGLISH Clarke Operator's Manual (EN) - Ultra Speed Burnisher FORM NO. 71280A - 13 - ®...
  • Page 14 Este manual contiene información importante acerca del uso y la seguridad de la máquina. Si no lee el manual antes de utilizar su máquina Clarke o de intentar realizar los procedimientos de reparación o mantenimiento de la misma, usted o el resto del personal podrían sufrir lesiones; asimismo, podrían producirse daños a la máquina o a otras propiedades.
  • Page 15: Instrucciones De Seguridad Para El Operador

    Para evitar daños al cable de alimentación, procure que el disco, el portadisco o las ruedas no toquen el cable, cuando la máquina funciona. Levante siempre el cable por encima de la máquina. No tire de la máquina para acercar la máquina. Clarke ®...
  • Page 16: Presentación De La Máquina

    Lea todas las indicaciones escritas en la máquina antes de la primera utilización. Compruebe que todos los adhe- sivos y las instrucciones estén colocados en los sitios previstos. Si es preciso, haga un nuevo pedido a su distribuidor Clarke.
  • Page 17: Máquinas 120V - Instrucciones Para La Conexión Eléctrica

    Use un añadido de cable de 6 mm² de sección. No use ningún añadido de más de 15 metros de largo. Nunca conecte dos añadidos. Clarke ® Manual del operador (ES) - Ultra Speed Burnisher FORM NO. 71280A - 17 -...
  • Page 18: Máquinas 240V - Instrucciones Para La Conexión Eléctrica

    ¡ AVISO !: Use un añadido de cable de 4 mm² de sección. No use ningún aña- dido de más de 15 metros de largo. Nunca conecte dos añadidos. Clarke -18- FORM NO. 71280A ® Manual del operador (ES) - Ultra Speed Burnisher...
  • Page 19: Preparación De La Máquina Para Trabajar

    Esto es importante para evitar vibraciones y ahorrar al operador un cansancio inútil. Atornille de nuevo el portadisco (A). Figura 2 Vuelva la máquina a una posición vertical. Clarke ® Manual del operador (ES) - Ultra Speed Burnisher FORM NO. 71280A - 19 -...
  • Page 20: Funcionamiento De La Máquina

    Volver a colocar la tapa. Volver a poner la máquina en posición vertical. Clarke -20- FORM NO. 71280A ® Manual del operador (ES) - Ultra Speed Burnisher...
  • Page 21 Verifi cación y reparaciones La máquina debe ser verifi cada una vez al año por un centro técnico autorizado Clarke. Cualquier mantenimiento o reparación debe ser efec- tuado por un técnico autorizado Clarke. AVISO: El mantenimiento y las reparaciones deben ser efectuados por técnicos...
  • Page 22: Posibles Problemas Y Soluciones

    Centre correctamente el disco. El disco es usado o dañado. Coloque un disco nuevo. El disco es defectuoso. Inspeccione el disco e instale un nuevo disco. Clarke -22- FORM NO. 71280A ® Manual del operador (ES) - Ultra Speed Burnisher...
  • Page 23: Mantenimiento

    Para verifi car el colector y las escobillas de carbón, siga este procedimiento: Compruebe que el enchufe de la toma de red está desconectada. 1. Quite los tornillos y las cubiertas. Clarke ® Manual del operador (ES) - Ultra Speed Burnisher FORM NO. 71280A - 23 -...
  • Page 24 En tal caso, entregue la máquina a un centro técnico autorizado Clarke para cambiar el rectifi cador. Clarke -24- FORM NO.
  • Page 25 ESPAÑOL Clarke ® Manual del operador (ES) - Ultra Speed Burnisher FORM NO. 71280A - 25 -...
  • Page 26 La non-lecture de ce manuel avant d’utiliser ou d’entretenir votre machine Clarke risque de provoquer un accident ou d’endommager la machine ou son environnement. Vous devez avoir été formé à l’utilisation de cette machine avant de l’utiliser. Si l’opérateur n’est pas en mesure de lire ce Manuel, il devra se le faire expliquer entièrement avant de...
  • Page 27: Consignes De Sécurité Pour L'opérateur

    Pour éviter d'endommager le câble d'alimentation, veillez à ce que le disque, le porte-disque ou les roues ne touchent pas le câble lorsque la machine fonctionne. Soulevez toujours le câble au- dessus de la machine. Ne tirez pas le câble pour faire avancer la machine. Clarke ® Manuel de l’utilisateur (FR) - Ultra Speed Burnisher...
  • Page 28: Présentation De La Machine

    Vérifi ez que tous les auto-collants et les instructions sont positionnés aux endroits requis . Au besoin, recommandez-en chez votre revendeur Clarke. Toute modifi cation ou changement apportés á cette machine peuvent l' endommager ou blesser l' opératuer ou d' autres personnes se trouvant á...
  • Page 29: Machines 120V - Instructions Pour Le Raccordement Électrique

    Utilisez un câble de rallonge d'une section de 6 mm². N'utilisez pas de rallonge d'une longueur supérieure à 15 m. Ne raccordez jamais deux rallonges. Clarke ® Manuel de l’utilisateur (FR) - Ultra Speed Burnisher FORM NO. 71280A - 29 -...
  • Page 30: Machines 240V - Instructions Pour Le Raccordement Électrique

    ! AVERTISSEMENT !: Utilisez un câble de rallonge d'une section de 4 mm². N'utilisez pas de rallonge d'une longueur supérieure à 15 m. Ne raccordez jamais deux rallonges. -30- FORM NO. 71280A Clarke Manuel de l’utilisateur (FR) - Ultra Speed Burnisher ®...
  • Page 31: Préparation De La Machine Avant La Mise En Service

    (B). Ceci est important pour éviter des vibrations et épargner une fatigue inutile à l'opérateur. Revisser le porte-disque (A). Figure 2 Placer la machine à la position verticale. Clarke ® Manuel de l’utilisateur (FR) - Ultra Speed Burnisher FORM NO. 71280A - 31 -...
  • Page 32: Fonctionnement De La Machine

    Reposez le couvercle. Remettez la machine en position verticale. -32- FORM NO. 71280A Clarke Manuel de l’utilisateur (FR) - Ultra Speed Burnisher ®...
  • Page 33 Celui-ci se voilera et provoquera des vibrations. Vérifi cation et réparations La machine doit être vérifi ée une fois l'an dans un centre technique agréé Clarke. Tout entretien ou réparation doit être effectué par un technicien agréé Clarke. AVERTISSEMENT: L'entretien et les réparations doivent être effectués par...
  • Page 34: Pannes Courantes Et Solutions

    Recentrer le disque correctement. Le disque est usé ou endommagé. Placer un disque neuf. Le disque est défectueux. Inspectez et installez un nouveau disque. -34- FORM NO. 71280A Clarke Manuel de l’utilisateur (FR) - Ultra Speed Burnisher ®...
  • Page 35: Entretien

    Pour la vérifi cation du collecteur et des balais de carbone, suivre la procédure ci-après: Vérifi er que la fi che de la prise réseau est débranchée. Enlever les vis et les couvertures. Clarke ® Manuel de l’utilisateur (FR) - Ultra Speed Burnisher FORM NO. 71280A - 35 -...
  • Page 36 3. Tourner le porte-disque et inspecter la partie du collecteur qui est en contact avec les balais. 4. Confi er la machine à un centre technique agréé Clarke si une des conditions suivantes se présente: 1.) Présence de petits trous à la surface du collecteur. Voir fi...
  • Page 37 Ultra Speed Burnisher 120V & 240V with NEMA Plug Section II Parts Manual ( 71280A)
  • Page 38: Us1500 Assy

    4/2011 US1500 ASSY -38- FORM NO. 71280A Clarke ® Operator's Manual - Ultra Speed Burnisher...
  • Page 39 Label, Motor Cover (only used on models 01530A, 01531A) 71116A Label Motor Rose Work Horse (only used on model 01491B) 73323A Label Motor Clarke (only used on models 01530A, 01531A) 80290A Screw 10-32 X .38 HRCS 80292A Screw .25-20 X 1.00 Bhhr Sems...
  • Page 40: Us1500-2000Dc Assy

    5/2016 US1500DC-2000DC ASSY -40- FORM NO. 71280A Clarke ® Operator's Manual - Ultra Speed Burnisher...
  • Page 41 Wheel Plate Wldt NOTE 2 / TSB-FC-2014-004 56382808 Pivot Plate Wldt NOTE 2 / TSB-FC-2014-004 30739A Shroud Dust 56384009 Washer-Nylon-1.125x.030 56393565 Skirt Assy Handle, Assembly Clarke DC TSB-FC-2014-016 61869A Axle Rear 976240 Pad-Aqua-20-5/Cs 980413 Washer Retainer 980673 Washer Flat 1/2 X 7/8 X 3/64 56109766 Screwbuttonhead 1/4-20 X .63 Sems NOTE 2 / TSB-FC-2014-004...
  • Page 42: Handle Assy

    Screw 10-32 X .38 HRCS 80291A Washer, Flat #10 (.203x.734x.063) 80292A Screw .25-20 X 1.00 Bhhr Sems 80295A Washer Bowed 80297A Screw 1/4-20 X 1.75 Bh Zp Sems -42- FORM NO. 71280A Clarke ® Operator's Manual - Ultra Speed Burnisher...
  • Page 43: Wiring Diagrams

    4/2011 WIRING DIAGRAMS 120V HANDLE 230V HANDLE MOTOR Clarke ® Operator's Manual - Ultra Speed Burnisher FORM NO. 71280A -43-...
  • Page 44 9435 Winnetka Ave North Minneapolis, MN 55445 www.clarkeus.com Phone: 800-253-0367 Fax: 800-825-2753 ©2016 Nilfi sk, Inc. A Nilfi sk Brand...

Table of Contents