Table of Contents
Advertisement
E
Operator's
Manual
READ THIS BOOK
This book has important information for the use and safe operation of this machine. Failure to read
this book prior to operating or attempting any service or maintenance procedure to your ALTO
machine could result in injury to you or to other personnel; damage to the machine or to other property
could occur as well. You must have training in the operation of this machine before using it. If your
operator(s) cannot read English, have this manual explained fully before attempting to operate this
machine.
All directions given in this book are as seen from the operator's position at the rear of the machine.
For new books write to:
Form No. 70127B 4/01
., 2100 Highway 265, Springdale, Arkansas 72764.
ALTO U.S. INC
CLARKE TECHNOLOGY
ULTRA SPEED
BURNISHER
1700
Printed in the U.S.A.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Clarke ULTRA SPEED BURNISHER 1700
Summary of Contents for Clarke ULTRA SPEED BURNISHER 1700
- Page 1 All directions given in this book are as seen from the operator’s position at the rear of the machine. For new books write to: ., 2100 Highway 265, Springdale, Arkansas 72764. ALTO U.S. INC Form No. 70127B 4/01 CLARKE TECHNOLOGY Printed in the U.S.A.
-
Page 2: Table Of Contents
Section II - Parts and Service Manual Maintenance ................12 Assembly Drawing ..............14 Assembly Parts List ............15 Electrical Schematic ............... 16 Motor Drawing and Parts List ..........17 Page - 2 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700... -
Page 3: Operator Safety Information
WARNING: Use of this machine as a step or furniture could result in injury or damage. Do not use this machine as a step or furniture. Do not ride on this machine. CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700 Page -3 -... -
Page 4: Features And Specifications
High traffic/low Maintenance 976235 UHS Tan Burnish 1500-3000 Hard finish/high traffic Buffer Wet-look hard finish 976236 UHS Aqua Burnish 1500-3000 Aqua Soft finish/low traffic Buffer Wet-look soft finish Page - 4 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700... -
Page 5: 120 Volt Instructions For Electrical Connection
WARNING: If you use an extension cord, use an extension cord with minimum wire size 12 AWG. Do not use an extension cord longer than 50 feet. Do not join two extension cords. CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700 Page -5 -... -
Page 6: About The Machine
5. Be sure pad is properly centered on the driver. 6. Reinstall the retainer on the pad holder until pad is tightly secured (turn clockwise). NEVER OPERATE BURNISHER WITHOUT A PAD. Page - 6 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700... -
Page 7: How To Operate The Machine
The circuit breaker reset button is on the rear of the motor cover. Push the reset button to reset the circuit breaker. If the motor continues to stop, consult an authorized service person. CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700 Page -7 -... -
Page 8: Care And Maintenance
To make any repairs, take the machine to the nearest Clarke Technology authorized repair location. WARNING: Maintenance and repairs must be done by authorized personnel only Page - 8 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700... -
Page 9: How To Correct Problems In The Machine
The pad is not installed Remove the pad. Install the pad correctly. excessively. correctly. Center the pad properly. The pad is worn or damaged. Install a new pad. CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700 Page -9 -... - Page 10 NOTES Page - 10 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700...
-
Page 11: Section Ii - Parts And Service Manual
® Ultra Speed Burnisher 1700 Section II Parts and Service Manual (70127B) CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700 Page -11 -... -
Page 12: Maintenance
3. Pull back each spring and pull the brush out of the holder. Keep the lead wire connected. 4. Turn the pad driver and look at the part of the commutator that the brushes touch. Page - 12 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700... - Page 13 Take the machine to an authorized repair location to have a Clarke Technology authorized repair person replace the rectifier. CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700 Page -13 -...
-
Page 14: Assembly Drawing
CLARKE TECHNOLOGY Ultra Speed Burnisher 1700 Assembly Parts List 4/01 Page - 14 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700... -
Page 15: Assembly Parts List 4/01
Retainer Pad (incl. w/25) 77378A Label, Clarke Technology 57K 30185A Baffle (NOTE: Part Number 34259A requires retainer 80201A) NOTE: indicates a change has taken place since last publication of this manual CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700 Page -15 -... -
Page 16: Electrical Schematic
CLARKE TECHNOLOGY Ultra Speed Burnisher 1700 Electrical Schematic 120Volts 11/00 Page - 16 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700... -
Page 17: Motor Drawing And Parts List
Bearing - Lower 40405A Bottom End Plate 980076 Wave Washer 55646A Cord Assembly 59606A Varistor (120V) (w/8) 55647A Yellow Lead (w/8) 55648A Red Lead(w/8) 627580 Strain Relief 58056A Strain Relief CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700 Page -17 -... - Page 18 NOTES...
- Page 19 NL-4131 NJ Vianen 1355 West Oak Common Lane +31 347 324000 (770) 973-5225 ALTO Sverige AB, Molndal (Sweden) Aminogatan 18 CLARKE TECHNOLOGY Box 4029 AMERICAN SANDERS TECHNOLOGY S-431 04 Molndal A.L. COOK TECHNOLOGY +46 31 706 73 00 Customer Service Headquarters and...
- Page 20 (b). Return the product to the nearest Clarke Technology repair location. Transportation charges to and from the repair location must be prepaid by the purchaser. (c). Clarke Technology will repair the product and or replace any defective parts without charge within a reasonable time after receipt of the product.
Need help?
Do you have a question about the ULTRA SPEED BURNISHER 1700 and is the answer not in the manual?
Questions and answers