Clarke Ultra Speed Burnisher Operator's Manual
120v & 230v with nema plug
Hide thumbs
Also See for Ultra Speed Burnisher:
- Operator's manual (37 pages) ,
- Operator's manual (45 pages)
Table of Contents
Advertisement
Electronic Service
Manuals
This electronic document is provided as a service to our customers.
We do not create the contents of the information contained in this docu-
ment. Should you have detailed questions pertaining to the information
contained in this document, you may contact Michco, or the manufac-
turer which provided the original information in this electronic deliver-
able. Michco's only part in this electronic deliverable was the electronic
assembly process. By providing this manual on line we are not guaran-
teeing parts availability.
You may contact Michco through the following methods:
Phone (517) 484-9312 or (800) 331-3339
2011 N. High St. -- Lansing, Michigan -- 48906
Fax: (517) 484-9836
Email: CustServe@Michco.com
Web site: www.Michco.Com
Parts Web site: www.FloorMachineParts.Com
Order Parts on Line at:
www.FloorMachineParts.Com
Directly to Parts & Service:
By Email:
Shop@Michco.com
By Fax: (517) 702-2041
By Voice: Use numbers above.
Serving the Cleaning Industry Since 1922
Notice: All copyrighted material remains property of original owners, all trademarks are property of respective owners.
Manuals are subject to Manufacturer's reproduction limitations. Originals or reproductions were provided by manufacturers
through a request. We make no warranty as to the correctness of information provided in this document and you assume
all risk. By placing these manuals on line we are not declaring our corporation to be an manufacturer authorized dealer or
provider, please check our web site for authorized manufacturers we represent.
Advertisement
Table of Contents
Related Manuals for Clarke Ultra Speed Burnisher
Summary of Contents for Clarke Ultra Speed Burnisher
- Page 1 Electronic Service Manuals This electronic document is provided as a service to our customers. We do not create the contents of the information contained in this docu- ment. Should you have detailed questions pertaining to the information contained in this document, you may contact Michco, or the manufac- turer which provided the original information in this electronic deliver- able.
- Page 2 All directions given in this book are as seen from the operator’s position at the rear of the machine. For new books write to: ., 2100 Highway 265, Springdale, Arkansas 72764. ALTO U.S. INC Form No. 70243A 5/03 CLARKE TECHNOLOGY Printed in the U.S.A.
-
Page 3: Table Of Contents
Section II - Parts and Service Manual Maintenance ................26 Assembly Drawing ..............30 Assembly Parts List ............31 Electrical Schematic ............... 32 Motor Drawing and Parts List ..........33 Page - 2 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher... - Page 4 Máquinas 230V - Instrucciones para la conexión eléctrica ... 15 Preparación de la máquina para trabajar ........17 Funcionamiento de la máquina............ 19 Posibles problemas y soluciones ..........23 CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher Page -3 -...
- Page 5 Machines 230V - Instructions pour le raccordement électrique ...... 15 Préparation de la machine avant la mise en service ........17 Fonctionnement de la machine ..............19 Pannes courantes et solutions ..............24 Page - 4 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher...
-
Page 6: Operator Safety Information
WARNING: Any alterations or modifications of this machine could result in damage to the machine or injury to the operator or other bystanders. Alterations or modifications not authorized by the manufac- turer voids any and all warranties and liabilities. CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher Page -5 -... -
Page 7: Instrucciones Para La Seguridad Del Operador
Si opera la máquina con un cable de alimentación estropeado, se puede causar una electrocución. No use nunca la máquina si el cable de alimentación está estropeado. No tire de la máquina usando el cable eléctrico. Page - 6 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher... -
Page 8: Consignes De Sécurité Pour L'opérateur
Vous devez avoir reçu une formation avant d'utiliser la machine. Si vous (ou les membres de votre personnel) ne connaissez pas le français, veuillez vous faire expliquer le manuel complètement avant de commencer à utiliser la machine. CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher Page -7 -... - Page 9 Pour éviter une surcharge du moteur, ne pas utiliser la polisseuse pour un récurage à l'eau. La polisseuse n'est pas équipée d'une jupe pour retenir l'eau. Risque de projections. Page - 8 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher...
-
Page 10: Features And Specifications
Hard finish/high traffic Buffer Wet-look hard finish 976236 UHS Aqua Burnish 1500-3000 Aqua Soft finish/low traffic Buffer Wet-look soft finish 976234 SHS Buffer Buff Dry/Spray 600-1500 Beige Glossy finish Spray CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher Page -9 -... -
Page 11: Presentación De La Máquina
Buffer reflejante mate 976236 UHS Aqua Pulido en seco 1500-3000 aqua semimate/paso leve Buffer reflejante semimate 976234 SHS Buffer Taponamient o en seco/ 600-1500 beige brillante pulverización Page - 10 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher... -
Page 12: Présentation De La Machine
Buffer réfléchissant mat 976236 UHS Aqua Polissage à sec 1500-3000 semi-mat/peu de Buffer passage réfléchissant semi- mat 976234 SHS Buffer Tamponnage à sec/ 600-1500 beige brillant pulvérisation CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher Page -11 -... -
Page 13: 120 Volt Instructions For Electrical Connection
WARNING: If you use an extension cord, use an extension cord with minimum wire size 12 AWG. Do not use an extension cord longer than 50 feet. Do not join two extension cords. Page - 12 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher... -
Page 14: Máquinas 120V - Instrucciones Para La Conexión Eléctrica
6 mm². N'utilisez pas más de 15 metros de largo. Nunca conecte de rallonge d'une longueur supérieure à 15 m. dos añadidos. Ne raccordez jamais deux rallonges. CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher Page -13 -... -
Page 15: 230 Volt Instructions For Electrical Connection
WARNING: If you use an extension cord, use an extension cord with minimum wire size 12 AWG. Do not use an extension cord longer than 50 feet. Do not join two extension cords. Page - 14 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher... -
Page 16: Máquinas 230V - Instrucciones Para La Conexión Eléctrica
No use ningún añadido de de rallonge d'une longueur supérieure à 15 m. más de 15 metros de largo. Nunca conecte Ne raccordez jamais deux rallonges. dos añadidos. CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher Page -15 -... -
Page 17: How To Prepare Machine For Operation
2. If the needle shows in the white area, turn the height Figure 4 adjustment knob to the left to increase the pad pressure. Page - 16 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher... -
Page 18: Preparación De La Máquina Para Trabajar
CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher Page -17 -... -
Page 19: How To Operate The Machine
The circuit breaker reset button is near the pad pressure meter. Push the button to reset the circuit breaker. If the motor continues to stop, consult an authorized service person. Page - 18 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher... -
Page 20: Funcionamiento De La Máquina
Si le moteur ne volver a conectar el cortacircuito. Si el motor no fonctionne toujours pas, consulter un technicien agréé. funciona todavía, avise a un técnico autorizado. CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher Page -19 -... - Page 21 To make any repairs, take the machine to the nearest Clarke Technology authorized repair location. WARNING: Maintenance and repairs must be done by authorized personnel only Page - 20 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher...
- Page 22 Clarke Technology. ogy. AVERTISSEMENT: L'entretien et les AVISO: El mantenimiento y las réparations doivent reparaciones deben ser être effectués par des efectuados por técnicos techniciens qualifiés. cualificados. CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher Page -21 -...
-
Page 23: How To Correct Problems In The Machine
Remove the pad. Install the pad correctly. excessively. correctly. Center the pad properly. The pad is worn or damaged. Install a new pad. The pad is defective. Inspect and install a new pad. Page - 22 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher... -
Page 24: Posibles Problemas Y Soluciones
Centre correctamente el disco. El disco es usado o dañado. Coloque un disco nuevo. El disco es defectuoso. Inspeccione el disco e instale un nuevo disco. CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher Page -23 -... -
Page 25: Pannes Courantes Et Solutions
Recentrer le disque correctement. Le disque est usé ou Placer un disque neuf. endommagé. Le disque est défectueux. Inspectez et installez un nouveau disque. Page - 24 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher... -
Page 26: Section Ii - Parts And Service Manual
® Ultra Speed Burnisher Section II Parts and Service Manual (70243A) CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher Page -25 -... -
Page 27: Maintenance
To check the commutator and the carbon brushes, follow this procedure: 1. Remove the two top screws of the motor cover. 2. Remove the cover. Page - 26 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher... - Page 28 Vérifier que la fiche de la prise réseau est débranchée. Enlever les deux vis de fixation situées sur la face supérieure du couvercle du moteur. CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher Page -27 -...
- Page 29 Keep the lead wire connected. 4. Turn the pad driver and look at the part of the commutator that the brushes touch. 5. Take the machine to a Clarke Technology autho- SMALL UNEVEN rized repair location if you see any of the following...
- Page 30 à sa vitesse normale, il se peut que le redresseur soit endommagé. Dans ce cas, confier la machine à un centre technique agréé Clarke Technol- ogy, où le redresseur sera remplacé. CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher Page -29 -...
-
Page 31: Assembly Drawing
CLARKE TECHNOLOGY Ultra Speed Burnisher Assembly Parts List 5/03 40 43 38 37 112 69 Page - 30 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher... -
Page 32: Assembly Parts List 5/03
Bushing, Bottom 70036A Label US 2000 58684A Spring 70037A Label US 2500 51169A Bearing 170686 Locknut NOTE:u indicates a change has been made since the last publication of this manual. CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher Page -31 -... -
Page 33: Electrical Schematic
CLARKE TECHNOLOGY Ultra Speed Burnisher Electrical Schematic 120 & 230 Volts 11/00 Page - 32 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher... -
Page 34: Motor Drawing And Parts List
Strain Relief 52046A Commutator Bracket w/ Rectifier (#8 includes #'s 6, 7, 19, 20 and 21) MOTOR SCHEMATIC CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher Page -33 - Page -33 -... - Page 35 NOTES...
- Page 36 NL-4131 NJ Vianen 1355 West Oak Common Lane +31 347 324000 (770) 973-5225 ALTO Sverige AB, Molndal (Sweden) Aminogatan 18 CLARKE TECHNOLOGY Box 4029 AMERICAN SANDERS TECHNOLOGY S-431 04 Molndal A.L. COOK TECHNOLOGY +46 31 706 73 00 Customer Service Headquarters and Factory...
- Page 37 (b). Return the product to the nearest Clarke Technology repair location. Transportation charges to and from the repair location must be prepaid by the purchaser. (c). Clarke Technology will repair the product and or replace any defective parts without charge within a reasonable time after receipt of the product.