Important Safety Instructions; Safety Notices - Numark DJ2Go2 User Manual

Important Safety Instructions

(1) Read and keep these instructions. Heed all warnings and follow all Instructions. (2) Do not use this apparatus near water.
(3) Clean only with dry cloth. (4) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat. Do not place exposed flame sources such as lighted candles on the
apparatus. (5) Only use attachment/accessories specified by the manufacturer. (6) Refer all servicing to qualified service
personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped. (7) Power Sources: This product should be connected to a power
supply only of the type described in these operating instructions, or as marked on the unit. (8) Water and Moisture: This
product should be kept away from direct contact with liquids. The apparatus shall not be exposed to dripping or splashing
and that no objects filled with liquids, such as vases, shall be placed on the apparatus. (9) This apparatus is for professional
use only. Intended operational climate: tropical, moderate. (10) Warning: Excessive sound pressure (high volumes) from
headphones can cause hearing loss. (11) Warning: Please refer to any important information (e.g., electrical, safety, etc.)
printed on the exterior bottom enclosure or rear panel before installing or operating the product.

Safety Notices

WARNING: To reduce the risk of fire or electrical shock, do not expose this appliance to rain or moisture. Electrical equipment
should NEVER be kept or stored in damp environments.
NOTICE CONCERNING FCC REGULATIONS: You are cautioned that changes or modifications not expressly approved by the
part responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures: (a) reorient or relocate the receiving
antenna; (b) move this unit; (c) increase the separation between the equipment and receiver; (d) connect the equipment into an
outlet on a circuit different from that to which the receiver is connected; (e) be sure that all cables are properly shielded, using a
choke or ferrite where appropriate; or (f) consult the dealer or an experienced radio/television technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
For Canadian models:
• This device complies with Industry Canada licence-exempt RSSs. Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
• Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or
lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than
that necessary for successful communication.
• This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by
Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna
impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the
maximum gain indicated for that type, are strictly prohibited for use with this device.
• This unit does not exceed the Class B limits for radio noise emission from digital apparatus set out in the radio
interference regulations of the Canadian Department of Communications.
ESD/EFT Warning: This unit may contain a microcomputer for signal processing and control functions. In very rare
situations, severe interference, noise from an external source, or static electricity may cause it to lock up. In the
unlikely event that this should happen, turn off the unit, wait at least five seconds, and then turn it back on again.
The pins of connectors identified with this ESD warning symbol should not be touched.
For best audio quality, avoid using this device in a high RF-radiated environment. In an environment with radio frequency
interference, the unit may malfunction and resume normal operation after removal of the interference.
Correct Disposal of This Product: This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return
your used device, please use the return and collection systems or contact the retailer where the product was
purchased. They can take this product for environmentally safe recycling.
General Note on the Declaration of Conformity: We hereby declare that this device is in accordance with the
essential requirements of the European Directive 1999/5/EC. The full EU declaration of conformity can be
requested at the following address:
inMusic GmbH
Harkortstr. 12 - 32
40880 Ratingen
GERMANY
6