Related Manuals for Aztec PROSCRUB
Summary of Contents for Aztec PROSCRUB
- Page 1 PROSCRUB OWNER’S MANUAL PAGE 1 OWNER’S MANUAL THE PROSCRUB Automatic 20” Floor Autoscrubber WWW.AZTECPRODUCTS.COM 800-331-1423 * 201 COMMERCE DRIVE, MONTGOMERYVILLE, PA 18936 08-2017...
-
Page 2: Table Of Contents
PROSCRUB OWNER’S MANUAL PAGE 2 TABLE OF CONTENTS INTRODUCTION & GENERAL SAFETY MESSAGE INFORMATION PG 3-5 PROSCRUB SPECIFICATIONS PG 5 BEFORE OPERATION CHECKLIST PG 6 DRAINING AND FILLING THE TANKS PG 7-8 PROSCRUB OPERATION PG 9-10 PROSCRUB HELPFUL HINTS PG 10... -
Page 3: Introduction & General Safety Message Information
All information in this Owner’s Manual is up to date and based on the latest product information available at the time of printing. Aztec Products, Inc. reserves the right to make changes at any time without notice or incurring obligation. This Owner’s Manual and the maintenance log must be kept as a permanent part of the machine and remain with the machine if resold. - Page 4 PROSCRUB OWNER’S MANUAL PAGE 4 IMPORTANT SAFETY INFORMAITION The 20” ProScrub automatic scrubber is designed to scrub floors in an indoor environment and is not recommended for any other use. Call Aztec 800-331-1423 for additional application questions. Never use flammable or explosive cleaning solutions such as gasoline, kerosene, solvents, thinners, etc.
-
Page 5: Proscrub Specifications
½ hp, 2 stage, 24volt Scrubbing Pressure Batteries Two (2) 130 amp/hour, 12volt Deep cycle, lead/acid PROTECT YOUR WARRANTY! Read this Owner’s Manual carefully; all questions regarding the care and safety of this equipment, please call AZTEC PRODUCTS: (800) 331-1423 info@ aztecproducts.com www.aztecproducts.com 08-2017... -
Page 6: Before Operation Checklist
PROSCRUB OWNER’S MANUAL PAGE 6 BEFORE OPERATION CHECKLIST Before beginning your pre-operation checklist, the machine must be on a level surface, with the machine switch in the OFF position. Always check the following items before you start the machine: A. READ AND UNDERSTAND ALL SAFETY MESSAGES Carefully read and understand all SAFETY INSTRUCTIONS on pgs 3-6. -
Page 7: Draining And Filling The Tanks
PROSCRUB OWNER’S MANUAL PAGE 7 DRAINING AND FILLING THE TANKS Use only nonflammable chemicals. Damage or personal injury may occur. Use only non-foaming detergents and dilute according to the manufacturer’s instructions. If using powdered cleaners, dissolve thoroughly before adding to solution tank. - Page 8 PROSCRUB OWNER’S MANUAL PAGE 8 DRAINING AND FILLING THE TANKS continued DRAINING THE PROSCRUB SOLUTION TANK: 1.) Make sure Solution Control Knob is completely turned to OFF position 2.) Pull clear hose off bracket at back of the machine and drain into a bucket or into floor drain 3.) Turn Solution Control Knob clockwise to clean out solution flow system...
-
Page 9: Proscrub Operation
Failure to do so can result in personal injury and/or damage to the machine or property. The ProScrub autoscrubber should only be operated by fully qualified maintenance personnel. Do not operate, maintain, or service this autoscrubber unless you are trained and authorized. -
Page 10: Proscrub Helpful Hints
Cradle (see below and pg 8 for diagram). PROSCRUB OPERATION HELPFUL HINTS ❖ The ProScrub works best when operating in a straight path; turning the machine at too sharp an angle can result in squeegee spillover ❖ While scrubbing, periodically check the recovery tank. If foam buildup is heavy, use a defoamer to prevent damage. -
Page 11: Storage And Handling Safety Information
Always store equipment away from possible damage by falling objects. The ProScrub autoscrubber must be secured on a level surface when transporting in a vehicle. Secure the machine in the vehicle so it cannot move or bounce during transporting; damage may occur to the machine and/or the vehicle and surrounding objects. -
Page 12: Proscrub Maintenance Schedule
PROSCRUB OWNER’S MANUAL PAGE 12 MAINTENANCE SCHEDULE Machine should only be tipped back for service if properly turned OFF, in a safe environment and positioned on a flat surface. Do not tilt machine on its side; damage can occur to the machine, furniture, buildings and/or personal injury. - Page 13 PROSCRUB OWNER’S MANUAL PAGE 13 MAINTENANCE SCHEDULE (CONTINUED) DAILY o Remove and clean pad or brush o Remove and clean lint from ball float shutoff screen (located in recovery tank) o Drain and rinse both tanks; remove any clogging debris in vacuum intake hole in recovery tank o Raise squeegee and wipe with clean, damp cloth to remove any soil o Recharge batteries if necessary;...
-
Page 14: Battery Maintenance Schedule & Battery Charging
PROSCRUB OWNER’S MANUAL PAGE 14 BATTERY MAINTENANCE Before any battery maintenance is done, make sure batteries and charger are disconnected and unplugged from wall outlet to avoid shock. Keep battery terminals and surface clean and dry. 1.) To dissolve battery corrosion, mix a solution of baking soda and water. Brush solution carefully over battery. - Page 15 PROSCRUB OWNER’S MANUAL PAGE 15 BATTERY CHARGING continued Safety first. Contact an authorized service center as needed. To get the most life from your battery, recharge when the meter drops into the red zone. Do not continue to run the scrubber after meter has gone into the red zone.
-
Page 16: Solution Tank Parts
PROSCRUB OWNER’S MANUAL PAGE 16 SOLUTION TANK PARTS REF # DESCRIPTION PART # SOLUTION TANK 108-AS-1 DRAIN HOSE BRACKET 288-030-1000 MOTOR LIFT ADJUST. BRKT. 288-030-700 FOOT LEVER ADJUST. BRKT. 283-030-105 3/8 - 16*3/4" BOLT 164-10111 5/16 USS FLAT WASHER 164-20156... -
Page 17: Vacuum Tank Parts
PROSCRUB OWNER’S MANUAL PAGE 17 VACUUM TANK PARTS REF # DESCRIPTION PART # SCREW S2-97 4" LID S2-04 RECOVERY TANK 108-AS-2 HINGE 030-20H WASHER 164-20153 1/4 - 20*1/2" BOLT 164-10003 OVERFLOW ASSEMBLY 030-20-119 VACUUM MOTOR GASKET S2-20 VACUUM MOTOR 030-VACM 1/4 –... -
Page 18: Shroud Assembly Parts
PROSCRUB OWNER’S MANUAL PAGE 18 SHROUD ASSEMBLY PARTS REF # DESCRIPTION PART # SPLASH SKIRT 030-20-118 BRUSH SHROUD 108-AS-20 1 3/4" SHOULDER BOLT 196-70212 POLY WHEEL 156-PB03041-08 SWIVEL CASTER 156-030 FLAT WASHER 164-20153 1/4 - 20*1/2" BOLT 164-10003 08-2017... -
Page 19: Squeegee Assembly Parts
PROSCRUB OWNER’S MANUAL PAGE 19 SQUEEGEE ASSEMBLY PARTS REF # DESCRIPTION PART # FRONT SUPPORT 283-030-235 SQUEEGEE BLADE (FRONT) 030-20-SRF SHOULDER BOLT 196-70212 POLY WHEEL 156-PB-03041-08 SQUEEGEE (WELDED ASSBLY) 288-030-200 WHEEL BRACKET 288-030-221 WHEEL BOLT 164-1129087 WHEEL & BRACKET NUT... -
Page 20: Drive Assembly Parts
PROSCRUB OWNER’S MANUAL PAGE 20 DRIVE ASSEMBLY PARTS REF # DESCRIPTION PART # 20" PAD DRIVER 030-20-262 5/16 - 18*3/4" BOLT 164-10059 1/4" FLAT WASHER 164-20155 MOTOR BRUSH ADAPTER 288-030-800 MOTOR SWIVEL PLATE 283-030-130 BRUSH MOTOR 030-BRUSHM 5/16 - 18*1" BOLT 164-10063 5/16"... -
Page 21: Control Panel Parts
PROSCRUB OWNER’S MANUAL PAGE 21 CONTROL PANEL PARTS REF # DESCRIPTION PART # HANDLE GRIP (FOAM) 030-GRIP HANDLE ADJUSTMENT BRACKET 283-030-125 HANDLE BOLT 164-132DA23020P HANDLE ADJUSTMENT KNOB 030-20-114 HANDLE BASE BRACKET 283-030-120 ROCKER SWITCH 030-20-108 CONTROL PANEL PLATE 283-030-275 COVER PLATE... -
Page 22: Wiring Diagram
PROSCRUB OWNER’S MANUAL PAGE 22 WIRING DIAGRAM 08-2017... -
Page 23: Troubleshooting
PROSCRUB OWNER’S MANUAL PAGE 23 TROUBLESHOOTING PROBLEM SYMPTOM SOLUTION No power, nothing runs Batteries need charging Charge the batteries Batteries faulty Replace batteries Loose battery cable Tighten cable connection Batteries not connected properly Connect properly Brush motor does not run... -
Page 24: Return Goods Policy
PROSCRUB OWNER’S MANUAL PAGE 24 RETURN GOODS POLICY The ProScrub autoscrubber is an innovative and unique machine. Since it was first introduced it has undergone a process of continuous improvement. This has been accomplished based on comments and suggestions by customers and by the return of any defective or failed parts. Examining causes of failures firsthand allows us to solve current problems and avoid them in the future. -
Page 25: Proscrub Warranty
It is unlikely that you will ever have a warranty claim if you properly maintain your machine. * Battery warranty is one (1) year from battery manufacturer, call Aztec for information: 800-331-1423 † Charger warranty is one (1) year from charger manufacturer, Lester Electrical: 402-477-8988 This warranty is non-transferable.