NX-CDR7R SERVICE MANUAL COMPACT COMPONENT CDR SYSTEM NX-CDR7R Area suffix B ------------------------------- U.K. E ----------- Continental Europe EN ------------ Northern Europe SP-NXCDR7 CA-NXCDR7R SP-NXCDR7 Contents Safety Precautions Flow of functional operation until Preventing static electricity TOC read 1-32 Important for laser products...
Page 2
NX-CDR7R 1. This design of this product contains special hardware and many circuits and components specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Services should be performed by qualified personnel only.
NX-CDR7R Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.1. Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as DVD players.
NX-CDR7R Important for Laser Products 5.CAUTION : If safety switches malfunction, the laser is able 1.CLASS 1 LASER PRODUCT to function. 2.DANGER : Invisible laser radiation when open and inter 6.CAUTION : Use of controls, adjustments or performance of lock failed or defeated. Avoid direct exposure to beam.
NX-CDR7R Disassembly method Metal cover <Main body> Removing the metal cover (See Fig.1 and 2) Remove the four screws A on the back of the body. Remove the screw B on each side of the body. Remove the rear part of the metal cover upward while pulling the lower part of both sides.
Page 6
NX-CDR7R Removing the front panel assembly Front panel assembly CN712 CN704 (See Fig.3 to 6) Prior to performing the following procedure, remove the metal cover. CN705 Disconnect the card wire from connector CN705, CN708, CN704 and CN712 on the main board.
Page 7
NX-CDR7R Removing the main board CN704 (See Fig.7 and 8) CN712 Front panel assembly Prior to performing the following procedure, remove CN705 the metal cover. CN708 Disconnect the card wire from connector CN704, CN705, CN706, CN707, CN708, CN709 and CN712 on the main board on the upper side of body.
Page 8
NX-CDR7R Removing the rear cover / rear panel (See Fig.9 to 12) Prior to performing the following procedure, remove the metal cover. Remove the four screws F on the back of the body, and press the two joints c inward to release.
Page 9
NX-CDR7R Removing the tuner board (See Fig.13) Joint e Prior to performing the following procedure, remove the metal cover, the main board and the rear panel. Disconnect the wire from connector CN802 on the tuner board on the right side of the body.
Page 10
NX-CDR7R Power amplifier board 2 Removing the power amplifier board 1 / CN403 power amplifier board 2 / heat sink Power board Power amplifier board 1 CN101 (See Fig.16 to 19) Prior to performing the following procedure, remove the metal cover, the main board, the rear panel and the tuner board.
Page 11
NX-CDR7R Removing the fan (See Fig.20) Prior to performing the following procedure, remove the metal cover, the main board, the rear panel, the tuner board, the power amplifier board 1, the power amplifier board 2 and the heat sink. REFERENCE: The fan is detachable without removing the CDR mechanism assembly.
Page 12
NX-CDR7R Notch i Removing the CDR mechanism cover / Clamp CDR mechanism assembly CDR mechanism cover (See Fig.22 to 27) Prior to performing the following procedure, remove the metal cover, the front panel assembly, the rear panel, the main board and the tuner board.
Page 13
NX-CDR7R Remove the three screws O attaching the CDR mechanism cover. Move the CDR mechanism assembly in the direction of the arrow, inside of the CDR mechanism cover, to disengage it from the three joint bosses marked j. Then remove the CDR mechanism assembly toward the front.
Page 14
NX-CDR7R CDR mechanism assembly Removing mechanism assembly only (See Fig.28 and 29) REFERENCE: mechanism assembly detachable without removing the CDR mechanism cover. Prior to performing the following procedure, remove the metal cover, the front panel assembly and the main board.
Page 15
NX-CDR7R Removing the CD changer mechanism CDR mechanism assembly assembly (See Fig.31 to 33) REFERENCE: The CD changer mechanism assembly is detachable without removing the CDR mechanism cover mechanism assembly. Prior to performing the following procedure, remove the metal cover, the front panel assembly and the...
Page 16
NX-CDR7R Removing power transformer assembly (See Fig.34 and 35) Prior to performing the following procedure, remove the metal cover, the main board, the rear panel, the Band tuner board, the power amplifier board 1, the power board and the heat sink.
Page 17
NX-CDR7R LCD board <Front panel assembly section> Prior to performing the following procedures, remove the metal cover and the front panel assembly. Removing the LCD board (See Fig.36) Remove the four screws S on the back of the front panel assembly.
Page 18
NX-CDR7R Removing the door motor (See Fig.40 and 41) Door motor Prior to performing the following procedure, remove the motor board. Remove the belt from the door motor. Remove the screw Y attaching the door motor bracket. Remove the two screws Z.
Page 19
NX-CDR7R Removing the control board (See Fig.42 to 46) Prior to performing the following procedure, remove the function switch board, the motor board and the belt. Remove the belt. Rotate the pulley (1) and move the control panel assembly toward the front until it stops.
Page 20
NX-CDR7R <Changer mechanism assembly> Removing the servo control board (See Fig.1 to 4) ATTENTION: Make sure the sub chassis unit is locating at the lowest position. If not,perform the following procedure from 1 to 3. Insert a screwdriver into the sub chassis slot on the...
Page 21
NX-CDR7R Top cover Removing the tray unit (See Fig.5 to 8) The tray unit can be removed despite the position of the sub chassis unit, but the lowest position is recommended to expedite the work. Remove the four screws B attaching the top cover on the top of the body.
Page 22
NX-CDR7R Removing the side unit (L) and (R) Joint h Side unit (R) (See Fig.9-1 to 9-5) Select arm Prior to performing the following procedures, remove the servo control board, the top cover and the tray Joints e unit. Remove the two screws C attaching the side unit (L).
Page 23
NX-CDR7R Removing the sub chassis unit (See Fig.10 to 12) Prior to performing the following procedures, remove the servo control board, the top cover, the tray unit, the side unit (L) and the side unit (R). Turn the hook gear counterclockwise to move the...
Page 24
NX-CDR7R Flap base unit Removing the flap base unit and the gear Joint tab j base unit (See Fig.13 and 14) Joint tab i Prior to performing the following procedures, remove the servo control board, the top cover, the tray unit, the side unit (L) and the side unit (R).
Page 25
NX-CDR7R Top cover Removing the pickup (See Fig.16 to 20) From the top of the body, remove the three screws H attaching the clamper base unit. Remove the clamper base unit with the two rods attached to the clamper base unit and the top cover.
Page 26
NX-CDR7R Removing traverse mechanism Joint o assembly (See Fig.21) Prior to performing the following procedure, remove the servo control board and the clamper base unit. Remove the three screws K attaching the traverse mechanism assembly. Detach the rear part of the traverse mechanism assembly upward to release the joint o with the sub chassis unit.
NX-CDR7R Disassembly method Joints a <Speaker section> Removing the tweeter speaker (See Fig.1 to 5) Release the four bosses of the joint a and remove the front grill toward the front. Front grill Turn over the body and insert a slotted screwdriver into the two holes b of the front panel assembly.
Page 28
NX-CDR7R Removing the squawker speaker Box assemby (See Fig.6) Prior to performing the following procedure, remove the front grille and the front panel assembly. Remove the four screws B on the front side of the box assembly. Disconnect the two wires from the squawker speaker terminal.
NX-CDR7R Adjustment method Measurement instruments required for adjustment Radio input signal 1. Low frequency oscillator, AM modulation frequency : 400Hz This oscillator should have a capacity to output 0dBs Modulation factor : 30% to 600ohm at an oscillation frequency of 50Hz-20kHz.
NX-CDR7R Confirm method of operation Check mode All lighting FL display and reducing time operation of clock <Setting method of all lighting FL display> "STANDBY/ON" key is pushed while pushing "REC/REC MUTING" key by the stand-by state. <Setting method of reducing time operation of clock>...
Page 31
NX-CDR7R Running operation When this mode is executed, the operation of the recording and the playback is repeated. Please use to confirm operation. It is necessary to put the recorded disk or CD-DA in tray 1 of changer mechanism beforehand to execute this item, and put CD-RW of the blank disk in recording mechanism.
NX-CDR7R Flow of functional operation until TOC read Check Point Slider turns REST Play Key Power ON Confirm that the voltage at the pin13 SW ON. of CN601 is "H"\"L"\"H". Automatic tuning of TE offset Check that the voltage at the...
NX-CDR7R Replacement of laser pickup Maintenance of laser pickup (1) Cleaning the pick up lens Before you replace the pick up, please try to Turn off the power switch and, disconnect the clean the lens with a alcohol soaked cotton power cord from the ac outlet.
NX-CDR7R Description of major ICs UPD784216AGF (IC701) : System micon 1.Terminal layout 2.Pin function Pin No. Symbol Function PROTECT Power amplifier output protect detection SPK-RELAY SPK-relay control signal SURROUND Surround output control signal SMUTE System mute control signal POUT1 FL power supply control signal output...
Page 35
NX-CDR7R Pin No. Symbol Function CDR-RREQ CDR request signal RDCLK Clock for data communication No connect KEYP Power on key input +BCTL No connect AVDD Power supply AVREF0 Reference voltage KEY0 Key control 0 input terminal KEY1 Key control 1 input terminal...
Page 36
NX-CDR7R MN662790RSC (IC651) : Digital servo & processor 1.Terminal layout 2.Pin function MN662790RSC (1/2) Pin No. Symbol Function BCLK Bit clock output for SRDATA LRCK Identifying signal output of L,R SRDATA Serial data output DVDD1 Power supply for digital circuit...
Page 37
NX-CDR7R MN662790RSC (2/2) Pin No. Symbol Functions PLLF2 Terminal for loop filter characteristic switch for PLL DSLBDA Non connect WVEL Non connect RF Signal output IREF Standard electric current input terminal Bias terminal for DSL DSLF Loop filter terminal for DSL...
Page 38
NX-CDR7R UPD780076GK502 (IC251) : Unit micon 1.Terminal layout 2.Pin function Pin No. Pin No. Symbol Description Symbol Description ES2SCK O EEPROM serial clock output /RESET O Reset signal output E2SDL O EEPROM serial data I/O O Synchronizatio /asynchronous system Not use(for flash micon)
Page 39
NX-CDR7R BR24C01AFV-W-X (IC201) : EEPROM 1.Terminal layout 2.Block diagram 1kbit EEPROM ARRAY 8bit 7bit SLAVE/WORD ADDRESS DATA 7bit ADDRESS REGISTER DECODER REGISTER START STOP CONTROL LOGIC HIGH VOLTAGE GEN. Vcc LEVEL DETECT 3.Pin function Pin name Function Power supply Ground (0v)
Page 45
NX-CDR7R LA1838 (IC1): FM AM IF AMP&detector, FM MPX decoder 1. Block Diagram DECODER RF.AMP ANIT-BIRDIE MUTE BUFF STEREO P-DET AM IF PILOT 384KHz COMP S-METER AM/FM S-CLRVE S-METER IF-BUFF TUNING STEREO DRIVE DRIVE FM IF 2. Pin Function Symbol...
Page 47
NX-CDR7R NJM4580D (IC301) : Dual operation amplifier 1.Terminal layout A OUT A -IN B OUT A +IN B -IN B +IN (TOP VIEW) 2.Block diagram INPUT OUTPUT XC62HR3502P-X (IC291) : Regulator 1.Terminal layout 2.Pin function Symbol Function Power supply ON/OFF...
Page 51
NX-CDR7R VICTOR COMPANY OF JAPAN, LIMITED AUDIO & COMMUNICATION BUSINESS DIVISION PERSONAL & MOBILE NETWORK BUSINESS UNIT. 10-1,1Chome,Ohwatari-machi,maebashi-city,371-8543,Japan No.21030 200110(S)
Page 52
NX-CDR7R In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as the resistor ( diode ( ) and ICP ( ) or identified by the " " mark nearby are critical for safety.
Page 53
NX-CDR7R Block diagram LVA10280-A2 LVA10280-A1 CF1 , Q1 IC1852 DI1851 FM IN FM IF AMP LF810 FLD DRIVER LF820 FM DET IC701 AM DET FILTER AM IN IC851 REMOCON J8001 SYSTEM MICON LINE IN FRONT CONTROL IC705 LVA10280-A3 INVERTER Q8101 , Q8201...
Page 54
NX-CDR7R NX-CDR7R Standard schematic diagrams System control section To E-2 on page 2-5 To F-2 on page 2-5 Q3161 2SD2144S/VW/-T 2SD2144S/VW/-T Q3162 R3169 10/25 CN710 CN711 C3153 220K R3161 QGB1214J1-12S QGB1214J1-10S R3168 4.7K R3167 C3253 R3261 C3163 10/50 C3164 10/25...
NX-CDR7R PARTS LIST [ NX-CDR7R ] * All printed circuit boards and its assemblies are not available as service parts. CA-NXCDR7R / SP-NXCDR7R Area suffix B ------------------------------- U.K. E ----------- Continental Europe EN ------------ Northern Europe - Contents - 3- 3 Exploded view of general assembly and parts list (Block No.M1)
NX-CDR7R Exploded view of general assembly and parts list Block No. Main board 105 104 Out put board LCD board Power amplifier board(2) LED board Operation SW board Power amplifier board(1) Power suplly connection board Door motor CDR control board...
Page 69
NX-CDR7R Parts list (General assembly) Parts list (General assembly) Block No. M1MM Block No. M1MM Item Parts number Parts name Q'ty Description Area Item Parts number Parts name Q'ty Description Area LV10573-002A FRONT PANEL 1 MIPS/SPRAY/SILK LV33026-001A FUNCTION BUTTON 1 ABS/VACUUM METAL...
Page 70
NX-CDR7R Parts list (General assmbly) Block No. M1MM Item Parts number Parts name Q'ty Description Area QYSDST3006Z SCREW 1 M.TRA PWB+SUB CHASSIS LV30225-011A SPACER LV32972-001A PWB COVER 1 FOR MINI TR PWB FMYH4004-001 PLASTIC RIVET LV21108-002A REAR PANEL QYSBSGY3008E SPECIAL SCREW 1 R.PANEL+BOTTOM...
Page 72
NX-CDR7R Parts list (CD Changer mechanism) Block No. MAMM Item Parts number Parts name Q'ty Description Area LV20581-001A CHASSIS UNIT RF-500TB-12560 MOTOR VKS5548-001 MOTOR PULLEY QYSPSP2603Z SCREW LV31586-001A SELECT GEAR LV41427-001A SELECT SPRING LV20588-001A GEAR BASE UNIT QYSDST2606Z SCREW LV41431-001A...
Page 73
NX-CDR7R CD-R/RW loading mechanism assembly and parts list Block No. Grease =EM-30L =CFD-4007ZYZ...
Page 74
NX-CDR7R Parts list (CD-R/RW loading mechanism) Block No. MRMM Item Parts number Parts name Q'ty Description Area LOADING BASE LV10454-007A QAR0164-001 MOTOR 1 MABUCHI LV42087-001A MOTOR PULLEY QYSPSPU1730Z SCREW 1 FOR MOTOR VKZ4777-003 MINI SCREW LV42209-001A BELT LV42084-002A PULLEYGEAR MIDDLE GEAR...
Page 75
NX-CDR7R Electrical parts list (Main board) Block No. 01 Item Remarks Parts number Parts name Area Item Remarks Parts number Parts name Area NCB31CK-223X C CAPACITOR CF 3 QAX0610-001Z C DISCRIMINATOR NCB31CK-103X C CAPACITOR CN581 QGF1205F1-05 CONNECTOR TO MAIN QETN1HM-106Z...
Page 76
NX-CDR7R Electrical parts list (Main board) Block No. 01 Item Remarks Parts number Parts name Area Item Remarks Parts number Parts name Area C3943 NCB31HK-103X C CAPACITOR C8513 NCB31HK-561X C CAPACITOR C3946 QETN1HM-226Z E CAPACITOR 22MF 20% 50V C8514 NCB31HK-561X...
Page 77
NX-CDR7R Electrical parts list (Main board) Block No. 01 Item Remarks Parts number Parts name Area Item Remarks Parts number Parts name Area IC705 TC74HCT04AF-X VOL BUFF R 12 NRSA63J-472X MG RESISTOR IC851 GP1U261X IR DETECT UNIT R 13 NRSA63J-103X...
Page 78
NX-CDR7R Electrical parts list (Main board) Block No. 01 Item Remarks Parts number Parts name Area Item Remarks Parts number Parts name Area R3261 NRSA63J-332X MG RESISTOR R7702 NRSA63J-102X MG RESISTOR R3262 NRSA63J-182X MG RESISTOR R7703 NRSA63J-102X MG RESISTOR R3263...
Page 79
NX-CDR7R Electrical parts list (Main board) Block No. 01 Item Remarks Parts number Parts name Area R7797 NRSA63J-102X MG RESISTOR R7799 NRSA63J-103X MG RESISTOR R7801 QRJ146J-181X UNF C.RES I/M 180 5% 1/4W R7802 NRSA63J-183X MG RESISTOR R7803 NRSA63J-473X MG RESISTOR...
Page 80
NX-CDR7R Electrical parts list (AMP board) Block No. 02 Item Remarks Parts number Parts name Area Item Remarks Parts number Parts name Area CN101 QGB2510K2-06 CONNECTOR C4001 QCBB1HK-103Y C CAPACITOR .010MF 10% 50V CN102 QGB2510K2-15 CONNECTOR C4003 QETN1EM-476Z E CAPACITOR...
Page 81
NX-CDR7R Electrical parts list (AMP board) Block No. 02 Item Remarks Parts number Parts name Area Item Remarks Parts number Parts name Area D5904 1N4003S-T5 SI DIODE R1102 QRE141J-273Y C RESISTOR 27K 5% 1/4W D5906 1N4003S-T5 SI DIODE R1103 QRE141J-181Y...
Page 82
NX-CDR7R Electrical parts list (AMP board) Block No. 02 Item Remarks Parts number Parts name Area Item Remarks Parts number Parts name Area R4035 QRE141J-471Y C RESISTOR 470 5% 1/4W S6202 QSW0651-001Z TACT SWITCH FADE IN/OUT R4036 QRE141J-471Y C RESISTOR...
Page 83
NX-CDR7R Electrical parts list (Power board) Block No. 03 Item Remarks Parts number Parts name Area CN901 QGA7901C1-02 CONNECTOR POWER CORD(PRI) CN902 QGB2510J1-07 CONNECTOR TO REAR PWB CN903 QGB2510J1-09 CONNECTOR TO REAR PWB CN904 QGA7901C1-02 CONNECTOR CN905 QGA2501F1-05 CONNECTOR FOR HP...
Page 84
NX-CDR7R Electrical parts list (CD servo board) Block No. 04 Item Remarks Item Parts number Parts name Remarks Area Parts number Parts name Area C 250 NCB31CK-104X C CAPACITOR E2P VDD-VSS C 851 QERF1CM-106Z E CAPACITOR VCC-M.GND C 253 NCB31CK-104X...
Page 85
NX-CDR7R Electrical parts list Block No. 05 Block No. 04 Electrical parts list (CD servo board) Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area CN620 QGB1214K1-08S CONNECTOR R 294 NRSA63J-103X MG RESISTOR IC PULL DOWN...
NX-CDR7R Packing materials and accessories parts list Block No. Block No. A1~A5 SP-NXCDR7R CA-NXCDR7R 3-22...
Page 88
NX-CDR7R Parts list (Packing) Block No. M3MM Item Parts number Parts name Q'ty Description Area PACKING CASE LV33029-001A LV10583-001A PACKING PAD(F) LV10584-001A PACKING PAD(R) QPC02503510P POLY BAG 1 FOR ACCESSARY QPC05006515P POLY BAG 1 FOR SET POLY BAG QPA01002503 8300043931...