Honeywell P531 Operating Manual page 16

MODELS P531, P532 AND P532UI OPERATING MANUAL
*40056
Channel "A" Primary Read/Write
* 000001 bit 0
* 000002 bit 1
* 000003 bit 2
* 000004 bit 3
* 000005 bit 4 (bit 4 and 5 are viewing head attached
to channel)
* 000006 bit 5 0 ,0 = no viewing head 0,1 = vh #1
....etc.
* 000007 bit 6 IR // for Advanced heads
* 000008 bit 7 UV // for Advanced heads
*40057
Channel "B" Primary Read/Write
* 000001 bit 0
* 000002 bit 1
* 000003 bit 2
* 000004 bit 3
* 000005 bit 4 (bit 4 and 5 are viewing head attached
to channel)
* 000006 bit 5 0 ,0 = no viewing head 0,1 = vh #1
....etc.
* 000007 bit 6 IR // for Advanced heads
* 000008 bit 7 UV // for Advanced heads
*40058
Channel "C" Primary Read/Write
* 000001 bit 0
* 000002 bit 1
* 000003 bit 2
* 000004 bit 3
* 000005 bit 4 (bit 4 and 5 are viewing head attached
to channel)
* 000006 bit 5 0 ,0 = no viewing head 0,1 = vh #1
....etc.
* 000007 bit 6 IR // for Advanced viewing heads
* 000008 bit 7 UV // for Advanced viewing heads
*40059
Pin status R/O
* 000001
* 000002
* 000003
* 000004 bit 3 522 mode pin
PORTC.3
* 000005 bit 4 Channel A Primary = 1 Alt = 0
PORTC.4 (same as 400002 00001)
* 000006 bit 5 Channel B Primary = 1 Alt = 0
PORTC.5
* 000007 bit 6 Channel B Primary = 1 Alt = 0
PORTC.6
* 000008
*40060 SERIAL Number R/O
*40061 ID number READ and WRITE (Signed Integer)
*40062 Operational time each unit = 2 hours of continuous
power on time (R/O)
*40063 Flame On Channel A alternate (0 -> 2999)
*40064 Flame On Channel B alternate (0 -> 2999)
*40065 Flame On Channel C alternate (0 -> 2999)
*40066 Flame Off Channel A alternate (0 -> 2999)
*40067 Flame Off Channel B alternate (0 -> 2999)
*40068 Flame Off Channel C alternate (0 -> 2999)
Page 13
*40069
Channel "A" Alternate Read/Write
* 000001 bit 0
* 000002 bit 1
* 000003 bit 2
* 000004 bit 3
* 000005 bit 4 (bit 4 and 5 are viewing head attached
to channel)
* 000006 bit 5 0 ,0 = no viewing head 0,1 = vh #1
....etc.
* 000007 bit 6 IR // for Advanced viewing heads
* 000008 bit 7 UV // for Advanced viewing heads
*40070
Channel "B" Alternate Read/Write
* 000001 bit 0
* 000002 bit 1
* 000003 bit 2
* 000004 bit 3
* 000005 bit 4 (bit 4 and 5 are viewing head attached
to channel)
* 000006 bit 5 0 ,0 = no viewing head 0,1 = vh #1
....etc.
* 000007 bit 6 IR // for Advanced viewing heads
* 000008 bit 7 UV // for Advanced viewing heads
*40071
Channel "C" Alternate Read/Write
* 000001 bit 0
* 000002 bit 1
* 000003 bit 2
* 000004 bit 3
* 000005 bit 4 (bit 4 and 5 are viewing head attached
to channel)
* 000006 bit 5 0 ,0 = no viewing head 0,1 = vh #1
....etc.
* 000007 bit 6 IR // for Advanced viewing heads
* 000008 bit 7 UV // for Advanced viewing heads
*40072 Gain Channel A 20ma Gain Alternate (0 – 100 )
*40073 Gain Channel B 20ma Gain Alternate (0 – 100 )
*40074 Gain Channel C 20ma Gain Alternate (0 – 100 )
Alarm set points Alternate
*40075 Alarm set point Channel A (0 -> 2999)
*40076 Alarm set point Channel B (0 -> 2999)
*40077 Alarm set point Channel C (0 -> 2999)
Alarm set points Alternate
*40078 Time Delay (upper nibble Ch B) Lower nibble channel A
(Read change Write)
*40079 FFRT (upper nibble Ch B) Lower nibble channel A(Read
change Write)
*40080 Reserved (do not write to this location) reads zero.
*40081 Time Delay Channel C Alternate
*40082 FFRT Channel C Alternate
*40083
Alternate / Primary Switch register Read/(Write
RS-422 only)
* 000001
* 000002
* 000003
* 000004
* 000005 bit 4 Channel A Primary = 1 Alt = 0
* 000006 bit 5 Channel B Primary = 1 Alt = 0
* 000007 bit 6 Channel B Primary = 1 Alt = 0
* 000008