Table of Contents
Advertisement
Quick Links
- 1 Preparing to Install Your Dishwasher
- 2 Drain Preparation
- 3 Connecting the Water Line to the Water Supply
- 4 Step 5: Install the 90° Water Supply Elbow
- 5 Step 4: Install the Power Cord
- 6 Step 6: Install the Drain Hose
- 7 Step 11: Securing the Dishwasher to the Countertop
- Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Insignia NS-DWH2BS8
Summary of Contents for Insignia NS-DWH2BS8
- Page 1 INSTALLATION GUIDE Top Control Dishwasher NS-DWH2BS8/NS-DWH2SS8/NS-DWR2BS8/NS-DWR2WH8/NS-DWR2SS8 Before using your new product, please read these instructions to prevent any damage.
-
Page 2: Table Of Contents
Step 17: Replacing the toekick.................23 Introduction Congratulations on your purchase of a high-quality Insignia product. Your NS-DWH2BS8/NS-DWH2SS8/ NS-DWR2BS8/NS-DWR2WH8/NS-DWR2SS8 represents the state of the art in dishwasher design and is designed for reliable and trouble-free performance. -
Page 3: Before You Begin
• Completion Time – One to three hours. New installations require more time than replacement installations. IMPORTANT – The dishwasher MUST be installed to allow for future removal from the enclosure if service is required. If you received a damaged dishwasher, you should immediately call Insignia Customer Service at 1-877-467-4289. FOR YOUR SAFETY CAUTIONS WARNINGS... -
Page 4: Preparing To Install Your Dishwasher
NS-DWH2BS8/NS-DWH2SS8/NS-DWR2BS8/NS-DWR2WH8/NS-DWR2SS8 Preparing to install your dishwasher Parts supplied: Hose clamp Top mounting clips (2) Wood screws (4) Drain hose Tools needed: Level 1/4 in. and 5/16 in. Phillips screwdriver Nut driver Adjustable wrench Flashlight Carpenters square Gloves Bucket New installations only... -
Page 5: Enclosure Requirements
Top Control Dishwasher Enclosure requirements • The rough cabinet opening must be at least 24 in. (60.96 cm) deep. • The maximum height of the opening is 35 in. (88.9 cm). • The dishwasher must be installed so that the drain hose is no more than 10 feet (3.01 m) in length, for proper drainage. -
Page 6: Drain Requirements
NS-DWH2BS8/NS-DWH2SS8/NS-DWR2BS8/NS-DWR2WH8/NS-DWR2SS8 Drain requirements • Follow all local codes and ordinances. • Do not exceed 10 ft. (3.01 m) of drain hose. • Do not connect the drain lines from other devices to the dishwasher drain hose. • The dishwasher must be connected to a waste line with an air gap (not provided) or a 32 in. (81.28 cm) high (min.) drain loop, depending on local codes and ordinances, to prevent back flow into the dishwasher. -
Page 7: Electrical Requirements
Top Control Dishwasher Electrical requirements • This appliance must be supplied with 120V, 60 Hz., and connected to its own, properly grounded branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse. • Wiring must be two wire with ground. •... - Page 8 NS-DWH2BS8/NS-DWH2SS8/NS-DWR2BS8/NS-DWR2WH8/NS-DWR2SS8 • Cable direct connections may pass through the same hole as the drain hose and hot water line, but power cords with plugs must pass through a separate hole. 1-1/2 in. (3.81 cm) diameter hole (max.) 2-1/2-3-1/2 in. (6.5-9.0 cm) from cabinet 24 in.
-
Page 9: Preparing The Hot Water Line
Top Control Dishwasher Preparing the hot water line • The water connection is on the left side of dishwasher. • The hot water line may enter the opening from either side, the rear, or the floor within the shaded area. •... -
Page 10: Installation Instructions
NS-DWH2BS8/NS-DWH2SS8/NS-DWR2BS8/NS-DWR2WH8/NS-DWR2SS8 Installation instructions Step 1: Check the door balance Caution • Opening the door of your dishwasher before it is installed will cause it to tip forward. Do not open the door until you are ready to install your dishwasher. -
Page 11: Step 2: Adjust The Leveling Legs
Top Control Dishwasher Step 2: Adjust the leveling legs 1 Move the dishwasher close to the installation location and lay it on its back. 2 Measure the installation height and the dishwasher height. 3 Extend the leveling legs out from the dishwasher base 1/4 in. (6.35 mm) less than the installation height. Adjust to 1/4 in. -
Page 12: Step 4: Install The Power Cord
NS-DWH2BS8/NS-DWH2SS8/NS-DWR2BS8/NS-DWR2WH8/NS-DWR2SS8 Step 4: Install the power cord Skip this step if the dishwasher will be direct wired. 1 Remove the junction box cover on the right front of the dishwasher. 2 Connect the incoming white (or ribbed) wire to the dishwasher’s white wire, the black (or smooth) wire to the dishwasher’s black wire, and the ground wire to the dishwasher’s green wire. -
Page 13: Step 6: Install The Drain Hose
Top Control Dishwasher Step 6: Install the drain hose 1 Turn the dishwasher upright. 2 Slide a screw-type hose clamp onto the drain hose. 3 Install the drain hose to the dishwasher drain outlet on the back of the dishwasher, then tighten the screw-type hose clamp. -
Page 14: Step 7: Inserting The Drain Hose Through The Cabinet
NS-DWH2BS8/NS-DWH2SS8/NS-DWR2BS8/NS-DWR2WH8/NS-DWR2SS8 Step 7: Inserting the drain hose through the cabinet • Insert the drain hose into the hole in the cabinet wall. If a power cord is used, guide the end through a separate hole. Tip: Position the water line and house wiring on the floor to avoid interfering with the base of the dishwasher. -
Page 15: Step 8: Slide The Dishwasher Partially Into The Cabinet
Top Control Dishwasher Step 8: Slide the dishwasher partially into the cabinet Caution: Do not push against the front panel with your knees. Damage will occur. 1 Position the dishwasher in front of the opening, then slide the dishwasher into the opening a few inches at a time. -
Page 16: Step 10: Level The Dishwasher
NS-DWH2BS8/NS-DWH2SS8/NS-DWR2BS8/NS-DWR2WH8/NS-DWR2SS8 Step 10: Level the dishwasher IMPORTANT: The dishwasher must be level for proper dish rack operation and wash performance. 1 Open the door, then place a level on the door and on the rack track inside the tub to make sure that the dishwasher is level. -
Page 17: Step 11: Securing The Dishwasher To The Countertop
Top Control Dishwasher Step 11: Securing the dishwasher to the countertop • For countertops made of wood or materials that won’t be damaged by drilling, use Method 1. • For countertops made of granite, marble, or other materials that could be damaged by drilling, use Method 2. •... -
Page 18: Step 12: Connecting The Water Supply Line
NS-DWH2BS8/NS-DWH2SS8/NS-DWR2BS8/NS-DWR2WH8/NS-DWR2SS8 Step 12: Connecting the water supply line 1 Slide the compression nut, then the ferrule over the end of the water supply line. 2 Insert the water supply line into the 90° elbow. 3 Slide the ferrule against the 90° elbow and secure it with the compression nut. -
Page 19: Step 13: Connecting The Drain Hose
Top Control Dishwasher Step 13: Connecting the drain hose IMPORTANT: Follow all local codes and ordinances. 1 Cut on the marked line as required for your installation. The drain hose’s molded end will fit 5/8”, 3/4” or 1" diameter connections on the air gap, waste tee, or garbage disposal. Cutting lines IMPORTANT: Do not cut corrugated portion of hose... - Page 20 NS-DWH2BS8/NS-DWH2SS8/NS-DWR2BS8/NS-DWR2WH8/NS-DWR2SS8 Method 2 - High drain loop to a waste tee or garbage disposal Fasten to the underside Fasten to the underside of the countertop of the countertop 32 in. (81.28 cm) 32 in. (81.28 cm) minimum minimum 18 in.
-
Page 21: Step 14: Connecting The Electrical Power
Top Control Dishwasher Step 14: Connecting the electrical power Turn off the electricity to the dishwasher’s electrical circuit. Skip this step if your dishwasher is equipped with a power cord. Make sure that the electrical power is turned off at the source. Warning •... -
Page 22: Step 15: Performing A Pre-Test Check
NS-DWH2BS8/NS-DWH2SS8/NS-DWR2BS8/NS-DWR2WH8/NS-DWR2SS8 Step 15: Performing a pre-test check Review this list after installing your dishwasher to avoid problems or charges for a service call not covered by your warranty. • Make sure that power is turned OFF. • Open the door and remove all foam and paper packaging. -
Page 23: Step 17: Replacing The Toekick
Top Control Dishwasher Step 17: Replacing the toekick • Place the toekick against the legs of the dishwasher. The slots should align with the toekick bracket screw holes. Allow the toekick to touch the floor. Install the toekick screws. You’ll need: Phillips screwdriver Specifications Capacity... - Page 24 1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico) INSIGNIA is a trademark of Best Buy and its affiliated companies. Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A. V3 ENGLISH ©2017 Best Buy. All rights reserved.