Intelligent Terminal Functions - Hitachi SJ300 Series Manual

Code Name
b100 Free-setting V/f frequency (1)
Free-setting V/f voltage (1)
b101
Free-setting V/f frequency (2)
b102
b103 Free-setting V/f voltage (2)
b104 Free-setting V/f frequency (3)
b105 Free-setting V/f voltage (3)
Free-setting V/f frequency (4)
b106
Free-setting V/f voltage (4)
b107
b108 Free-setting V/f frequency (5)
b109 Free-setting V/f voltage (5)
b110 Free-setting V/f frequency (6)
Free-setting V/f voltage (6)
b111
Free-setting V/f frequency (7)
b112
b113 Free-setting V/f voltage (7)
b120 Brake control enable
b121 Brake wait time for release
Brake wait time for acceleration
b122
Brake wait time for stopping
b123
b124 Brake wait time for confirmation
b125 Brake release frequency setting
b126 Brake release current setting
●C GROUP: INTELLIGENT TERMINAL FUNCTIONS
Code Name
C001 Terminal (1) function
C002 Terminal (2) function
C003 Terminal (3) function
C004 Terminal (4) function
C005 Terminal (5) function
C006 Terminal (6) function
C007 Terminal (7) function
C008 Terminal (8) function
C011 Terminal (1) active state
C012 Terminal (2) active state
C013 Terminal (3) active state
C014 Terminal (4) active state
C015 Terminal (5) active state
C016 Terminal (6) active state
C017 Terminal (7) active state
C018 Terminal (8) active state
C019 Terminal FW active state
Terminal (11) function
C021
C022 Terminal (12) function
C023 Terminal (13) function
Terminal (14) function
C024
C025 Terminal (15) function
Alarm relay terminal function
C026
C027 FM signal selection
C028 AM signal selection
C029 AMI signal selection
Description
0.0 - Free-setting V/f frequency (2)
0.0 - 800.0V
0.0 - Free-setting V/f frequency (3)
0.0 - 800.0V
0.0 - Free-setting V/f frequency (4)
0.0 - 800.0V
0.0 - Free-setting V/f frequency (5)
0.0 - 800.0V
0.0 - Free-setting V/f frequency (6)
0.0 - 800.0V
0.0 - Free-setting V/f frequency (7)
0.0 - 800.0V
0. - 400.Hz
0.0 - 800.0V
00(Disable) / 01(Enable)
0.00 - 5.00sec.
0.00 - 5.00sec.
0.00 - 5.00sec.
0.00 - 5.00sec.
0.00 - 99.99/100.0 - 400.0Hz
0.00 rated current to 2.00 rated current
× ×
Description
01(RV:Reverse) / 02(CF1:Multipeed(1)) / 03(CF2:Multispeed(2)) / 04(CF3:Multi-
speed(3)) / 05(CF4:Multispeed(4)) / 06(JG:Jogging) / 07(DB:External DC braking) /
08(SET:Second motor constants setting) / 09(2CH:Second accel./decel.) /
11(FRS:Free-run stop) / 12(EXT:External trip) / 13(USP:Unattended start protection) /
14(CS:Change to/from commercial power supply) / 15(SFT:Software lock) /
16(AT:Analog input selection) / 17(SET3:Third motor constants setting) /
18(RS:Reset) / 20(STA:3-wire start) / 21(STP:3-wire stop) / 22(F/R:3-wire fwd./
rev.) / 23(PID:PID On/Off) / 24(PIDC:PID reset) / 26(CAS:Control gain setting) /
27(UP:Remote-controlled accel.) / 28(DWN:Remote-controlled decel.) /
29(UDC:Remote-controlled data clearing) / 31(OPE:Operator control) /
32(SF1:Multispeed bit command(1) / 33(SF2:Multispeed bit command(2) /
34(SF3:Multispeed bit command(3) / 35(SF4:Multispeed bit command(4) /
36(SF5:Multispeed bit command(5) / 37(SF6:Multispeed bit command(6) /
38(SF7:Multispeed bit command(7) / 39(OLR:Overload limit change) /
40(TL:Torque limit enable) / 41(TRQ1:Torque limit selection(1)) /
42(TRQ2:Torque limit selection(2)) / 43(PPI:P/PI selection) / 44(BOK:Brake
confirmation signal) / 45(ORT:Orientation) / 46(LAC: LAD cancel) /
47(PCLR:Positioning deviation reset) / 48(STAT:90-degree pulse-train input phase
difference permission) / 255 (NO:Not selected)
00(NO) / 01(NC)
00(NO) / 01(NC)
00(NO) / 01(NC)
00(NO) / 01(NC)
00(NO) / 01(NC)
00(NO) / 01(NC)
00(NO) / 01(NC)
00(NO) / 01(NC)
00(NO) / 01(NC)
00(RUN:Run signal)/ 01(FA1:Frequency arrival signal (at the set frequency))/
02(FA2:Frequency arrival signal (at or above the set frequency))/ 03(OL:Overload
advance notice signal)/ 04(OD:Output deviation for PID control)/ 05(AL:Alarm sign-
al)/ 06(FA3:Frequency arrival signal (only at the set frequency))/ 07(OTQ:Over-
torque) / 08(IP:Instantaneous power failure signal)/ 09(UV:Under-voltage signal)/
10(TRQ:In torque limit)/ 11(RNT:RUN time over)/ 12(ONT:Power-on time over)/
13(THM:Thermal alarm)/ 19(BRK:Brake release)/ 20(BER:Brake error)/ 21(ZS:Zero
speed)
22(DSE:Speed deviation excessive) / 23(POK:Positioning completion)
24(FA4:Frequency arrival signal (at or above the set frequency)(2))/ 25(FA5:Fre-
quency arrival signal (only at the set frequency)(2))/ 26(OL2:Overload advance
notice signal(2))
(Terminal 11 - 13 or 11 - 14 are automatically configured as AC0 - AC2 or AC0 - AC3
per alarm code output selection)
00(Output frequency) / 01(Output current) / 02(Output torque) /
03(Digital output frequency-only at C027) / 04(Output voltage)
/ 05(Power) / 06(Thermal load ratio) / 07(LAD frequency)
[ = Allowed
⃝
= Not permitted
×
Default Setting
Run-time Run-time Data Edit
Setting
(Enabled at b031)
-FE(CE) -FU(UL)
0. 0. × ×
0.0 0.0 × ×
0. 0. × ×
0.0 0.0 × ×
0. 0. × ×
0.0 0.0 × ×
0. 0. × ×
0.0 0.0 × ×
0. 0. × ×
0.0 0.0 × ×
0. 0. × ×
0.0 0.0 × ×
0. 0. × ×
0.0 0.0 × ×
00 00 × ⃝
0.00 0.00 × ⃝
0.00 0.00 × ⃝
0.00 0.00 × ⃝
0.00 0.00 × ⃝
0.00 0.00 × ⃝
× ⃝
Rated current Rated current
[
= Allowed
⃝
= Not permitted
×
Default Setting
Run-time
Run-time Data Edit
Setting
(Enabled at b031)
-FE(CE) -FU(UL)
18 18
× ⃝
(RS) (RS)
16 16
× ⃝
(AT) (AT)
06 06
× ⃝
(JG) (JG)
11 11
× ⃝
(FRS) (FRS)
09 09
×
⃝
(2CH) (2CH)
03 13
× ⃝
(CF2) (USP)
02 02
×
⃝
(CF1) (CF1)
01 01
× ⃝
(RV) (RV)
00 00
× ⃝
00 00 × ⃝
00 00 × ⃝
00 00 × ⃝
00 00 ×
⃝
00 01
× ⃝
00 00 × ⃝
00 00 × ⃝
00 00 × ⃝
01 01
×
⃝
(FA1) (FA1)
00
00
×
⃝
(RUN)
(RUN)
03
03
× ⃝
(OL)
(OL)
07 07
×
⃝
(OTQ) (OTQ)
08
08
×
⃝
(IP) (IP)
05 05
⃝
×
(AL) (AL)
× ⃝
00 00
×
00 00 ⃝
00 00 × ⃝
]
]
16