Fine Tuning Functions - Hitachi SJ300 Series Manual

●B GROUP: FINE TUNING FUNCTIONS
Code Name
b001 Selection of automatic restart mode
b002 Allowable instantaneous power failure time
b003 Time delay enforced before motor restart
b004 Instantaneous power failure and under-voltage trip enable
Number of restarts after instantaneous power
b005
failure and under-voltage trip events
b006 Phase loss detection enable
b007 Restart frequency threshold
b012 Level of electronic thermal setting
Level of electronic thermal setting for second motor
b212
Level of electronic thermal setting for third motor
b312
b013 Electronic thermal characteristics
b213 Electronic thermal characteristics for second motor
b313 Electronic thermal characteristics for third motor
b015 Free-setting electronic thermal frequency (1)
b016 Free-setting electronic thermal current (1)
b017 Free-setting electronic thermal frequency (2)
b018 Free-setting electronic thermal current (2)
b019 Free-setting electronic thermal frequency (3)
b020 Free-setting electronic thermal current (3)
b021 Overload restriction operation mode
b022 Overload restriction setting
b023 Deceleration rate at overload restriction
b024 Overload restriction operation mode (2)
Overload restriction setting (2)
b025
b026 Deceleration rate at overload restriction (2)
b031
Software lock mode selection
b034 RUN/ power-on warning time
b035 Rotational direction restriction
b036 Reduced voltage soft start selection
b037 Function code display restriction
b040 Torque limit selection
b041 Torque limit(1) (Forward-driving in 4-quadrant mode)
Torque limit(2) (Reverse-regenerating in 4-quadrant mode)
b042
Torque limit(3) (Reverse-driving in 4-quadrant mode)
b043
b044 Torque limit(4) (Forward-regenerating in 4-quadrant mode)
b045 Torque limit LADSTOP enable
b046 Reverse RUN protection enable
Controlled deceleration and stop on power loss
b050
b051
DC bus voltage trigger level during power loss
Over-voltage threshold during power loss
b052
b053 Deceleration time setting during power loss
Initial output frequency decrease during
b054
power loss
b080 AM terminal analog meter adjustment
b081 FM terminal analog meter adjustment
b082 Start frequency adjustment
b083 Carrier frequency setting
Initialization mode
b084
b085 Country code for initialization
b086 Frequency scaling conversion factor
b087 STOP key enable
b088 Resume on free-run stop cancellation mode
b090 Dynamic braking usage ratio
b091 Stop mode selection
b092 Cooling fan control
b095 Dynamic braking control
b096 Dynamic braking activation level
b098 Thermistor for thermal protection control
b099 Thermistor for thermal protection level setting
Note:[ ]75kW and over
15
Description
00(Alarm output after trip, automatic restart disable) / 01(Restart at 0Hz) / 02(Re-
sume operation after frequency matching)/ 03(Resume previous frequency after
frequency matching, then decelerate to stop and display trip information)
0.3 - 25.0sec.
0.3 - 100.0sec.
00(Disable) / 01(Enable) / 02(Disable during stop and deceleration to stop)
00(16 times) / 01(Always restart)
00(Disable) / 01(Enable)
0.00 - 99.99/100.0 - 400.0Hz
0.20 rated current-1.20 rated current
× ×
0.20 × rated current-1.20 × rated current
0.20 rated current-1.20 rated current
× ×
00(Reduced torque) / 01(Constant torque) / 02(V/f free-setting)
00(Reduced torque) / 01(Constant torque) / 02(V/f free-setting)
00(Reduced torque) / 01(Constant torque) / 02(V/f free-setting)
0.-400.Hz
0.0-1000.A
0.-400.Hz
0.0-1000.A
0.-400.Hz
0.0-1000.A
00(Disable)/ 01(Enable during accel./constant speed)
/ 02(Enable during constant speed)
/ 03(Enable during accel./constant speed(Speed increase when regenerating))
rated current [ - 1.80
0.50 rated current-2.00
× ×
0.10-30.00
00(Disable) / 01(Enable during accel./constant speed)
/ 02(Enable during constant speed)
/ 03(Enable during accel./constant speed(Speed increase when regenerating))
rated current [ - 1.80
0.50 rated current-2.00
× ×
0.10-30.00
00(All parameters except b031 are locked when SFT from terminal is on)/ 01(All
parameters except b031 and output frequency F001 are locked when SFT from
terminal is on)/ 02(All parameters except b031 are locked)/ 03(All parameters
except b031 and output frequency F001 are locked)/ 10(Run-time data edit
mode)
0.-6553(65,530hr) (Output to intelligent terminal)
00(Enabled for both directions)/ 01(Enabled for forward)/ 02(Enabled for reverse)
00(Short)-06(Long)
00(All)/ 01(Utilized functions)/ 02(User-selected functions only)
00(4-quadrant setting)/ 01(Terminal input)/ 02(Analog O2 input)
/ 03(Expansion card 1)/ 04(Expansion card 2)
0.-200. % / no (Torque limit disable)
0.-200. % / no (Torque limit disable)
0.-200. % / no (Torque limit disable)
0.-200. % / no (Torque limit disable)
00(Disable)/ 01(Enable)
00(Disable)/ 01(Enable)
00(Disable)/ 01(Enable)
0.0 - 1000.V
0.0 - 1000.V
0.01 - 99.99/100.0 - 999.9/1000. - 3600.sec.
0.00 - 10.00Hz
0-255
0-255
0.10-9.99Hz
0.5-15.0kHz (To be derated) [0.5-10kHz]
00(Trip history clear) / 01(Parameter initialization)
/ 02(Trip history clear and parameter initialization)
00(Japanese version)/ 01(European version)/ 02(North American version)
0.1-99.9
00(Enable) / 01(Disable)
00(Restart at 0Hz) / 01(Resume operation after frequency matching)
0.0-100.0%
00(Deceleration to stop) / 01(Free-run stop)
00(Fan is always ON) / 01(Fan is ON during RUN including 5 min. after power-on and stop)
00(Disable) / 01(Enable during run) / 02(Enable during stop)
330-380/ 660-760V
00(Disable) / 01(PTC enable) / 02(NTC enable)
0.0-9999.Ω
Default Setting
-FE(CE) -FU(UL)
00 00
1.0 1.0
1.0 1.0
00 00
00 00
00 00
0.00 0.00
Rated current Rated current
Rated current Rated current
Rated current Rated current
01 01
01 01
01 01
0. 0.
0.0 0.0
0. 0.
0.0 0.0
0. 0.
0.0 0.0
01 01
Rated Rated
rated current]
×
current × 1.50 current 1.50
×
1.00 1.00
01 01
Rated Rated
rated current]
×
current 1.50 current 1.50
× ×
1.00 1.00
01 01
0. 0.
00 00
06 06
00 00
00 00
150. 150.
150. 150.
150. 150.
150. 150.
00 00
00 00
00 00
0.0 0.0
0.0 0.0
1.00 1.00
0.00 0.00
180 180
60 60
0.50 0.50
5.0[3.0] 5.0[3.0]
00 00
01 02
1.0 1.0
00 00
00 00
0.0 0.0
00 00
00 00
00 00
360/720 360/720
00 00
3000. 3000.
[ = Allowed ]
⃝
= Not permitted
×
Run-time Run-time Data Edit
Setting
(Enabled at b031)
×
⃝
⃝
×
× ⃝
× ⃝
×
⃝
⃝
×
× ⃝
× ⃝
× ⃝
× ⃝
⃝
×
× ⃝
× ⃝
× ⃝
× ⃝
⃝
×
× ⃝
× ⃝
× ⃝
⃝
×
⃝
×
× ⃝
⃝
×
× ⃝
× ⃝
× ⃝
× ×
× ⃝
× ⃝
⃝
×
× ⃝
× ⃝
× ⃝
⃝
×
× ⃝
× ⃝
× ×
× ×
× ×
× ×
× ×
⃝ ⃝
⃝
⃝
× ⃝
× ⃝
× ×
×
×
⃝ ⃝
× ⃝
× ⃝
× ⃝
×
×
× ×
× ⃝
× ⃝
× ⃝
⃝
×