Page 1
VX900T VX900T SERVICE MANUAL VX900T US Model Canadian Model Chassis No. SCC-L20F-A CHASSIS SPECIFICATIONS Power Consumption Picture tube 0.25-0.27 mm aperture grill pitch Maximum 19 inches measured diagonally 130 W Nominal 90-degree deflection 100 W Deflection frequency Video image area (18"...
Page 2
VX900T POWER SAVING FUNCTION If no video signal is input to the monitor, the NOTE: This monitor has three Power Saving modes. "NO INPUT SIGNAL" message appears. After By sensing the absence of a video signal from the about 30 seconds, the Power Saving function...
Page 3
VX900T SAFETY CHECK-OUT After correcting the original service problem, perform LEAKAGE TEST the following safety checks before releasing the set to the The AC leakage from any exposed metal part to earth ground customer: and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampere).
VX900T TABLE OF CONTENTS Section Title Page 1. GENERAL ................... 5 2. DISASSEMBLY 2-1. Cabinet Removal ............11 2-2. Service Position .............. 11 2-3. D, A, H and N Board Removal........11 2-4. Picture Tube Removal ........... 12 3. SAFETY RELATED ADJUSTMENT .........
SECTION 1 The instructions given here are partial abstracts from the Operating Instruction Manual. The page numbers shown reflect those of the Operating Instruction Manual. GENERAL Getting Started Getting Started Setup Table of Contents Connect the monitor to your computer system. Precautions .
Page 6
Getting Started Customizing Your Monitor Customizing Your Monitor The OSD (On-screen Display) System Use of the Tilt/Swivel Adjusting the Picture Brightness and Contrast This monitor can be adjusted within the angles shown below. To 3 If necessary, use the BRIGHTNESS buttons to select a specific turn the monitor vertically or horizontally, hold it at the bottom with Introducing the OSD System (BRIGHTNESS) v/V or 6 (CONTRAST)
Page 7
Customizing Your Monitor Customizing Your Monitor 3 Adjusting the shape of the 5 Adjusting the color of the picture 6 Adjusting the quality of the Adjusting the Settings picture (GEOM) (COLOR) picture (CONV) 1 Adjusting the centering of the The COLOR settings allow you to adjust the picture’s color The CONV settings allow you to adjust the quality of the picture by The GEOMETRY settings allow you to adjust the rotation and picture (CENTER)
Page 8
Customizing Your Monitor Customizing Your Monitor 9 Using the GRAPHIC Resetting the adjustments Degaussing the monitor Note • Before using this feature, the monitor must be in normal operation mode The monitor is automatically degaussed (demagnetized) when the ENHANCEMENT OSD (Green power indicator) for at least 30 minutes.
Page 9
• The computer is in power saving mode. Try pressing any key on the computer keyboard. INFORMATION Damper wires • Check that the computer’s power is “on.” MODEL : CPD VX900T • Check that the graphic video board is completely seated in the proper bus slot. SER NO : 1234567 MANUFACTURED : 1998-53...
Page 10
Additional Information Symptom Check these items Picture is fuzzy • Adjust the brightness and contrast (page 5). • Degauss the monitor* (page 9). • If CANCEL MOIRE is ON, the picture may become fuzzy. Decrease the moire cancellation effect (page 9) or set CANCEL MOIRE to OFF. Picture is ghosting •...
VX900T SECTION 2 DISASSEMBLY 2-1. CABINET REMOVAL 2-2. SERVICE POSITION Two claws PUSH H board Cabinet (additional board) PUSH A board D board 1 When the D-board is Two screws placed in service (BVTP 4 x 16) position, the Safety Earth Wire (green and yellow wire) is disconnected.
VX900T 2-4. PICTURE TUBE REMOVAL Demagnetization coil Two screws (BVTP 4 x 16) Tension spring A board Neck assy Deflection yoke Four screws (Tapping screw 5) Stand assy (D board) Picture tube shield Anode cap Cushion REMOVAL OF THE ANODE-CAP NOTE: Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon painted on the CRT, after removing the anode.
VX900T SECTION 3 SAFETY RELATED ADJUSTMENT b) HV Hold-Down Check When replacing parts shown in the table below, the 1) Using an external DC Power supply, apply the voltage following operational checks must be performed as a shown below between cathode of D908 on "D" Board safety precaution against X-ray emissions from the unit.
VX900T SECTION 4 ADJUSTMENTS Connect the communication cable of the connector located on the D board on the monitor. Run the service software and then follow the instructions. 1-690-391-21 A-1500-819-A 3-702-691-01 Interface Unit Connector Attachment IBM AT Computer To BUS CONNECTOR...
Page 15
VX900T Receive White cross-hatch. Convergence Specification Adjust HMC and VMC at six-pole magnet. < 6 Pole Magnet> Horizontal and Vertical 0.25mm 0.24mm 0.30mm 0.30mm C < 0.35mm Focus adjustment Receive R.B. cross-hatch. Adjust focus (V) and focus (H) for optimum focus.
VX900T 5-2. CIRCUIT BOARDS LOCATION 5-3. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS Note: • All capacitors are in µF unless otherwise noted. pF: µµF • When replacing parts shown in the table below, 50 WV or less are not indicated except for electrolytic.
Page 20
CN101 (2/2) CN801 (2/2) F U N C G N D . A S 2 0 0 1 - S 2 0 0 8 (FUNC CTRL) (MICRO, DSP) G N D KEY SCAN1 K E Y S C A N 1 P O W E R LED1 L E D 1...
Page 21
1 2 V D311 +12V CN313 (VIDEO) 1PS226-115 STBY+5V :PROT R 0 3 0 J001 1 0 0 :S-MICRO S T B + 5 V : C H I P IC002 C 3 5 2 R 3 3 0 LM2403 1 0 0 B.GND1 1 6 V...
VX900T SECTION 6 EXPLODED VIEWS Note: • • Items with no part number and no descrip- Items marked " " are not stocked tion are not stocked because they are sel- since they are seldom required for routine The components identified by shading dom required for routine service.
VX900T SECTION 7 ELECTRICAL PARTS LIST The components identified by [ in this manual RESISTORS Note: • have been carefully factory-selected for each All resistors are in ohms set in order to satisfy regulations regarding X- REF.NO. PART NO. DESCRIPTION...
Page 32
VX900T Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ sont critiques pour la securite. Ne les remplacer are critical for safety.
Page 33
VX900T Note: Note: The components identified by shading Les composants identifies per un trame and mark ¡ ¡ ¡ ¡ ¡ et une marque ¡ ¡ ¡ ¡ ¡ sont critiques pour la are critical for safety. Replace only with part number specified.
Page 34
VX900T Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ sont critiques pour la securite. Ne les remplacer are critical for safety.
Page 35
VX900T Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ sont critiques pour la securite. Ne les remplacer are critical for safety.
Page 36
VX900T Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ sont critiques pour la securite. Ne les remplacer are critical for safety.
Page 37
VX900T Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ sont critiques pour la securite. Ne les remplacer are critical for safety.
Page 38
VX900T Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ sont critiques pour la securite. Ne les remplacer are critical for safety.
Page 39
VX900T The components identified by [ [ [ [ [ in this manual have been Note: The components identified by shading carefully factory-selected for each set in order to satisfy and mark ¡ ¡ ¡ ¡ ¡ are critical for safety.
Page 40
VX900T Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ sont critiques pour la securite. Ne les remplacer are critical for safety.
Page 42
VX900T Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ sont critiques pour la securite. Ne les remplacer are critical for safety.
Page 43
VX900T NOTES: REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK — 53 —...
Page 44
VX900T NOTES: REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK — 54 —...
Page 45
VX900T REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK — 55 —...
Page 47
VX900T VX900T SERVICE MANUAL VX900T US Model Canadian Model Chassis No. SCC-L20F-A CHASSIS CORRECTION -1 Subject: Digital Convergence Adjustment Correct the service manual as shown. File this correction with the service manual. COLOR MONITOR...
Page 48
VX900T Section 4 Adjustments (Page 15) Step 4 Digital Convergence Adjustment Set CONV_SWITCH_NDX to 3 Step 1 Adjust area "A" as follows: Adjust area "03" - "83" with the following register: "X DYNAMIC CONV RX03" - "X DYNAMIC CONV RX83"...