Zone Programming; Zone Definition Values - Magellan MG6250 Section Programming Manual

Zone Programming

NOTE: If a device is assigned to a zone which is already programmed, a wireless zone will overwrite a hardwire zone.

Zone Definition Values

To program zone definitions and assign options:
1. Press and hold 0.
2. Enter your installer code or maintenance code.
3. Enter the four-digit zone you wish to program.
4. Enter the two-digit zone definition, refer to table 4.
5. Assign the partition, refer to table 5. By default, all zones are assigned to partition 1.
6. Select or de-select zone options using buttons 1 through 8, see table 6 or table 7.
7. Press the # key to save and proceed to the next zone. Repeat steps 3 to 6 for all remaining zones.
Table 4: Zone definitions
Input
Description
Value
00 Disabled (default)
01 Entry delay 1*
02 Entry delay 2*
03 Entry delay 1 (full arm)
04 Entry delay 2 (full arm)
05 Follow*
06 Follow (sleep/full arm)
07 Follow (full arm)
08 Instant*
09 Instant (sleep/full arm)
10 Instant (full arm)
11 Instant fire*
12 Delayed fire*
13 Instant fire silent*
14 Delayed fire silent*
15 24 hr. buzzer*
16 24 hr. burglary*
17 24 hr. hold-up*
18 24 hr. gas*
19 24 hr. heat*
20 24 hr. water*
21 24 hr. freeze*
22 24 hr. panic*
23 Follow no pre-alarm*
24 Instant no pre-alarm*
25 Keyswitch maintain*
26 Keyswitch momentary*
27 Delay 1 (sleep/full arm)
28 Delay 2 (sleep/full arm)
29 Unarmed*
30-32 Future use
33 Custom template 1†
34 Custom template 2†
35 Custom template 3
36 Custom template 4
*: Zone definitions that can be used in custom zone templates.
-: Zone definitions remain the same, regardless of arming type.
†: WARNING: Do not use these definitions for a common zone. The definition of a common zone follows the definition relative to the
area that gets the lowest level of arming. A problem may occur if a common zone follows an area armed in Stay/Sleep and an area
armed in Full. The resulting zone definition will be the one relative to the lowest level of arming which is Stay armed. The zone will
be considered as armed in both areas.
6 | Zone Programming
Arming Type
OFF Stay Arm
- -
Not armed Entry delay 1
Not armed Entry delay 2
Not armed Not armed
Not armed Not armed
Not armed Follow
Not armed Not armed
Not armed Not armed
Not armed Instant
Not armed Not armed
Not armed Not armed
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
Not armed -
Not armed -
- -
- -
Not armed Not armed
Not armed Not armed
Not armed Not armed
- -
Not armed Instant
Not armed Not armed
Not armed Entry delay 1
Not armed Instant
Sleep Arm Full Arm
- -
Entry delay 1 Entry delay 1
Entry delay 2 Entry delay 2
Not armed Entry delay 1
Not armed Entry delay 2
Follow Follow
Follow Follow
Not armed Follow
Instant Instant
Instant Instant
Not armed Instant
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
Entry delay 1 Entry delay 1
Entry delay 2 Entry delay 2
Not armed Not armed
- -
Instant Not armed
Instant Not armed
Instant Entry delay 1
Instant Entry delay 1
MG6250 • Section Programming Guide
Table 5: Partition assignment
Partition assignment
Input
Description
Value
1 Assign to partition 1
2 Assign to partition 2
3 Assign to both partitions
Table 6: Zone options
Zone options
Input
Description
Value
1 Auto zone shutdown
2 Bypassable zone
3 RF zone supervision
6 Intellizone delay
7 Delay arm transmission
8 Force arming
Input Value
Zone Alarm Type
4 5
OFF OFF Audible alarm
ON OFF Silent alarm
OFF ON Audible pulse
ON ON Report only
Table 7: Keyswitch options
Keyswitch options
Input Value
Levels of Arming
1 2
OFF OFF Disarm
ON OFF Stay Arm
OFF ON Sleep Arm
ON ON Full Arm
Input Value Description
3 -
4 Disarm partial arm only
5 Arm only
6 -
Version 1.6