Advertisement
Figure 5. Complete the Setup Wizard to set up your Unleashed network
H Once the Setup Wizard is finished, a "Configuring system settings and
rebooting" progress screen appears. Wait until the process is
complete.
Figure 6. Configuring system settings and rebooting
I
Connect to the WLAN that you configured in the Setup Wizard, and
click OK to reconnect. You will be redirected to the
unleashed.ruckuswireless.com login screen.
J
Enter your Admin Name and Password to login.
Figure 7. The Login page
K Upon successful login you will be presented with the Unleashed
Dashboard, which displays an overview of your Ruckus Unleashed
network.
Copyright © 2016 Ruckus Wireless, Inc.
Published September 2016, Part Number 800-71078-001 Rev B
Figure 8. : The Unleashed Dashboard
L The first time you log in, you will be presented with a "Registration"
screen prompting you to register your Unleashed AP with Ruckus. This
step is optional, and you can choose to skip the registration and
register your Unleashed APs later, at any time, if you prefer.
Figure 9. Registration page
Step 4: Customize Your Wireless LANs
Once the Unleashed Master AP has been initialized, you can fine-tune the
settings of your first WLAN (that you created during the setup wizard), and
create any additional WLANs needed prior to attaching additional
Unleashed member APs. Then, when you deploy additional member APs in
whatever order you prefer, they will automatically retrieve all WLAN
configuration settings (and any other settings you have configured) from
the Unleashed Master AP.
A From the Dashboard, click anywhere in the WiFi Networks section to
expand the display of your deployed WLANs.
B On the left side of the screen, select the WLAN box for the WLAN you
would like to configure, and click the Edit button to edit the
configuration; or click Create to create a new WLAN.
C If you made any changes to the original WLAN, you will be
disconnected and will need to reconnect once the changes have been
deployed on the AP radios.
Congratulations! Your Unleashed network is now configured and ready for
use. You may now proceed to Step 5: Deploy Additional Unleashed
Access Points.
Step 5: Deploy Additional Unleashed Access Points
Deploying additional Unleashed member APs is simply a matter of
connecting them to the same Layer 2 network (subnet) and providing
power. They will discover the Unleashed Master and join automatically. No
additional steps are necessary.
For More Information
For more information on managing your Unleashed network, refer to the
Ruckus Wireless Unleashed Access Point Online Help
https://support.ruckuswireless.com
.
I
AP
NSTALLING THE
The AP can be mounted on a flat surface, on a drop-ceiling T-bar, or on a
pole or flat surface. Refer to the following sections:
•
Mounting on a Flat Surface
•
Removing the AP from Flat-Surface Mounting Screws
•
Mounting the AP on a Drop-Ceiling T-Bar
•
Removing the AP from a Drop-Ceiling T-Bar
•
Mounting the AP on a Flat Surface or Pole Using the Optional
Secure Mounting Bracket
•
Removing the AP from the Optional Secure Mounting Bracket
Mounting on a Flat Surface
The factory-supplied mounting screws and plastic wall anchors allow you
to attach the AP to a wall or ceiling.
A Use the Mounting Template on the last page of this guide to mark the
locations for two drill holes on the mounting surface.
B Use a 4.75mm (3/16") drill bit to drill holes approximately 25mm (1")
deep into the mounting surface.
C Insert the factory-supplied anchors (A in Figure 10) and mounting
screws (B) into the mounting surface, leaving approximately 6 mm
(1/4") of the screw heads protruding from the surface.
Figure 10. Mounting the AP on a flat surface
A
C
B
, available from
Page 2 of 4
Advertisement
