ViewSat 9000HD User Manual page 10

1. A. 1 USALS
1. B. CHANNEL SCAN
It will be more convenient to use C hannel Scan
"
channel for a specified transponder offered from the satellite. As in
C hannel Scan a lso searches all channels broadcasted over a specific transponder
" "
using its predefined information. You can add a new transponder if you cannot find it on
the predefined transponder list.
Select Channel Scan m enu in I nstallation
" " "
displayed.
1. B. 1 Channel Scan
Select the desired satellite using the l eft/right
"
Select the A ntenna Configuration i con using the browse keys(
" "
17
.
Please go to Antenna Setup and select
USALS from motor.
Press the "OK" key then Pop-up will be
appeared.
Press arrow button to write Longitude
Press arrow button to write Latitude, then OK
to work.
p rocedure when you want to search
"
A ntenna Setup ,
" "
m enu, and the following screen will be
"
k eys ( ) .
" ◀ . ▶
) .
▲ . ▼ , ◀ . ▶
Press O K k ey, and set L NB Power ,
" " " "
L NB Type L NB Freq , 2 2KHz , and
" " , " " " "
D iSEqC 1.0 fields to the appropriate
" "
value using the l eft/right keys( ) at
" " ◀ . ▶
each field. Check the signal strength
and press E xit k ey.
" "
Select the S earch/Edit TP i con using the
" "
l eft/right keys( ) . Press O K k ey, and
" " ◀ . ▶ " "
select the desired transponder using the
u p/down k eys ( ) . Press O K k ey to
" " ▲ . ▼ " "
start the manual searching fo selected
r
transponder.
You can see the progressive status of channel searching.
If you cannot find the desired transponder from the transponder list, you can add it by
inputting appropriate parameter values for a new transponder using the
you want to change the parameter of an existent transponder, select the parameter
using the F 1 k ey, change its value and press the
" "
parameters.
Freq. : Input the frequency of the transponder you want to find manually.
S/R : Inputs the symbol rate of the transponder you want to find.
PoI. : Select the polarization of the transponder you want to find. In the
case of horizontal,18V and in the case vertical, 13V are output
through LNB line.
: Select the FEC of the transponder you want to find. You can select
FEC
the value of 1/2, 2/3, 3/4, 5/6, 7/8 or auto.
1. B. 2 Add Satellite
You can add a new satellite. Select the A dd Satellite
"
( ) ,and press the O K k ey.
◀ . ▶ " "
Select the S earch/Edit TP i con using the l eft/right
" " "
add a new transponder using the F 1 k ey. You should set various parameters of the
" "
transponder. The default name of the added satellites is
1. B. 3 Rename Satellite
You can also change the satellite name. Select the
l eft/right keys ( ) . Press O K k ey and select the character which you want to edit
" " ◀ . ▶ " "
using the browse keys ( , ) . Press the O K
▲ . ▼ ◀ . ▶ "
currently renamed using the F 2 k ey.
" "
1. B. 4 Delete Satellite
You can also delete the user satellite. Select the satellite that you want to delete from
the satellite list. Select the D elete Satellite i con using the browse keys (
" "
Press the O K k ey, and the selected satellite will disappear.
" "
F 1 k ey. When
" "
E xit k ey. Correctly set various
" "
i con using the l eft/right k eys
" " "
k ey ( ) . Press the O K k ey and
" ◀ . ▶ " "
U serSAT-No.
" "
R ename Satellite i con using the
" "
k ey to confirm. Save the character
"
, ) .
▲ . ▼ ◀ . ▶
18